• Dual channels
• Universal thermocouple, mV input
• 4-20mA outputs (sink/source)
• 7-32V DC loop/local

The DT233 model is a dual two-wire transmitter that isolates and converts millivolt or thermocouple sensor inputs to proportional 4-20mA control signals. Power is received from the output loop current.

Click here to watch a short video highlighting the features of the DT233.

 

• Dual channels
• Universal thermocouple, mV inputs
• Isolated current or voltage outputs
• 6-32V DC local/bus power

The DT333 model is a four-wire dual transmitter that isolates and converts millivolt or thermocouple sensor inputs to proportional control signals. Each channel supports DC current or voltage output. Click here to watch a short video highlighting the features of the DT333

• Universal TC type J, K, T, R, S, E, B, N or ±100mV input
• 4-20mA ouput (sink/source)
• 12-32 V DC loop/local power

The TT233 model is a space-saving two-wire transmitter that isolates and converts a millivolt or thermocouple sensor input to a proportional 4-20mA control signal. Power is received from the output loop current or a DC supply when using a three-wire connection. Click here to watch a short AcroMaggie video highlighting the TT230 Series.        

• Multi-range ±20mA or ±500mV input
• 4-20mA ouput (sink/source)
• 12-32 V DC loop/local power

The TT236 model is a space-saving two-wire transmitter that isolates and converts a DC current or low voltage input to a proportional 4-20mA control signal. A single unit supports both voltage and current input for extra flexibility. Power is received from the output loop current or a DC supply when using a three-wire connection. Click here to watch a short AcroMaggie video highlighting the TT230 Series.

• Multi-range 0Hz to 100KHz frequency input
• Multi-range 0Hz to 3KHz PWM input
• 4-20mA output (sink/source)
• 12-32V DC power

The TT239 model is a space-saving two-wire transmitter that isolates and converts a frequency, pulse, or pulse-width modulation (PWM) input to a proportional 4-20mA signal. You can select to measure either the input frequency or the duty cycle. Power is received from the output loop current or a DC supply when using a three-wire connection. Click here to watch a short AcroMaggie video highlighting the TT230 Series.    

• Universal thermocouple / millivolt input
• Universal current / voltage output
• 12-32V DC local / bus power

The TT333 model is a space-saving four-wire transmitter that isolates and converts a millivolt or thermocouple sensor input to a proportional control signal. DC current and voltage output are both supported on a single model. Click here to watch a short video highlighting the TT330 Series.    

• Multi-range ±20mA or ±500mV input
• Universal current/voltage output
• 12-32V DC power

DC current and voltage output are both supported on a single model. An optional DIN rail bus can deliver primary or redundant power to multiple units without wiring. Click here to watch a short video highlighting the TT330 Series.  

• Multi-range 0Hz to 100KHz input
• Universal current/voltage output
• 12-32V DC local/bus power

The TT339 model is a space-saving four-wire transmitter that isolates and converts a frequency or pulse input to a proportional control signal. DC current and voltage output are both supported on a single model. An optional DIN rail bus can deliver primary or redundant power to multiple units without wiring. Click here to watch a short video highlighting the TT330 Series.

•  Dual channels
•  ±20mA, ±500mV inputs
• 4-20mA outputs (sink/source)
• 7-32V DC loop power

The DT236 model is a dual two-wire transmitter that isolates and converts DC current or low voltage inputs to proportional 4-20mA control signals. Power is received from the output loop current or a DC supply when using a three-wire connection. Click here to watch a short video highlighting the features of the DT236.  

• Dual channels
• RTD (Pt, Ni, Cu), 0-4500 ohm inputs
• 4-20mA output (sink/source)
• 7-32V DC loop power

The DT235 model is a two-wire dual transmitter that isolates and converts RTD or linear resistance sensor inputs to a proportional 4-20mA control signal.

Click here to watch a short video highlighting the features of the DT235.

• Dual channels
• ±20mA, ±500mV inputs
• 0-20mA, ±10V outputs
• 6-32V DC local/bus power

The DT336 model is a four-wire dual transmitter that isolates and converts DC current or low voltage inputs to proportional control signals. Each channel supports DC current or voltage output.

Click here to watch a short video highlighting the features of the DT336.

• Dual channels
• RTD (Pt, Ni, Cu) or 0-4500 ohm input
• 0-20mA, ±10V outputs
• 6-32V DC local/bus power

The DT335 model is a four-wire dual transmitter that isolates and converts RTD or linear resistance sensor inputs to proportional control signals. Click here to watch a short video highlighting the features of the DT335.

• 16 discrete tandem input/output channels
• Modbus TCP/IP,  Ethernet/IP, Profinet, or i2o® communication

The XT1110 interfaces discrete I/O signals between measurement and control devices over Ethernet. Channels are individually configurable for input or low-side switched output operation.

• 0-11mA, 0-20mA, 4-20mA, ±20mA, or 0-20 amps AC Input
• 8 analog differential current input channels
• 12 to 32V DC Power (2.8W)
• Modbus TCP/IP, Ethernet/IP, Profinet
• i2o® peer-to-peer available for Modbus TCP/IP only

The XT1210 offers an isolated Ethernet network interface for up to eight differential current input channels. Isolated differential inputs deliver better measurements, superior noise rejection, and eliminate the need for current loop isolators.

• ±5V, ±10V, 0-5V, 0-10V Input
• 8 analog differential voltage input channels
• 12 to 32V DC Power (2.8W)
• Modbus TCP/IP, Ethernet/IP, Profinet
• i2o® peer-to-peer available for Modbus TCP/IP only

The XT1220 offers an isolated Ethernet network interface for up to eight differential voltage input channels.

• Dual channels
•  0-10V, ±10V inputs
• 4-20mA outputs (sink/source)
• 7-32V DC loop power

DT230 series signal conditioners provide two independent I/O channels in a single, space-saving unit. The DT237 model is a two-wire dual transmitter that isolates and converts high-level DC voltage inputs to a proportional 4-20mA control signal. Power is received from the output loop current or a DC supply when using a three-wire connection. Click here to watch a short video highlighting the features of the DT237.