Click to zoom
$360$375

Please sign in or register to see model options and to add products to your cart.

Product short description:
  • 16 discrete tandem input/output channels
  • Input: 0-32V DC, TTL thresholds
  • Output: 0-32V DC, open-drain, up to 250mA
  • Ethernet Communication: Modbus TCP/IP,  Ethernet/IP, Profinet, 10/100Base-T(X) PriorityChannel™ device determinism
  • i2o® peer-to-peer available for Modbus TCP/IP only
  • Power Requirement: 12 to 32V DC (2.5W)

The XT1110 interfaces discrete I/O signals between measurement and control devices over Ethernet. Channels are individually configurable for input or low-side switched output operation.

 

 

The XT1110 interfaces discrete I/O signals between measurement and control devices over Ethernet. Channels are individually configurable for input or low-side switched output operation.

Rugged construction, high density design, and easy USB-to-PC/Windows setup combine for a very effective I/O solution. These units are ideal for remote monitoring, distributed control, or SCADA applications.

Input/Output Ranges:
Input: 0-32V DC, TTL thresholds
Output: 0-32V DC, open-drain, up to 250mA
Ethernet Communication:
Modbus TCP/IP, i2o® peer-to-peer available for Modbus TCP/IP only
Ethernet/IP
Profinet
10/100Base-T(X)
PriorityChannel™ device determinism
Power Requirement: 12 to 32V DC (2.5W)

Performance Specifications

IMPORTANT: To prevent damage or errors from grounded PCs and surges, Acromag strongly recommends use of the USB-ISOLATOR when configuring an XT1000 I/O module.

USB Interface

USB Connector:
Type: USB Mini-B type socket, 5-pin
Data Rate: 12Mbps. USB v1.1 and 2.0 compatible
Cable Length: 5.0 meters maximum
USB Transient Protection: Transient voltage suppression on power and data lines
Driver: Not required. Uses Windows (HID) drivers

Input

Input Type: 16 active-low, buffered inputs, with a common connection. Inputs are tied in tandem to output drains for optional loopback monitoring of output state.
Input Signal Voltage Range: 0 to 32V DC
Input Current: 280µA, typical at 32V DC
Input Signal Threshold: 1.7V typical with 100mV of hysteresis
Input Resistance: 100K ohms, typical
Input Response Time: 10ms, nominal

Output

Output Type: 16 open-drain, smart, n-channel mosfet switches with a common source connection. Provides low-side (sinking) switching between the load and return.
Output Voltage: 0 to 32V DC
Output “ON” Resistance: 0.8 ohms typical, 1.6 ohms maximum
Output “ON” Current Range: 0 to 250mA DC, continuous (up to 4A total for all 16 channels combined). See Operating Temperature specification for effect of channels at full load. See manual for detailed effects of operating temperature.
Output Response Time: 10ms, nominal

Ethernet Communication

Protocols:
Modbus TCP/IP, i2o® peer-to-peer available for Modbus TCP/IP only
Ethernet/IP
or Profinet, depending on model number
Ethernet Communication Controller: Innovasic RapID™ Platform with PriorityChannel™ for determinism at the device regardless of network load.
Modbus TCP/IP (slave): Port 502 reserved. Supports up to 10 sockets
i2o Peer-to-Peer (master/slave): Can map 4-channel input groups to output groups at two destination IP addresses. Timed or change-of-state updates. Supports GPRS/GSM systems.
Ethernet/IP (adapter): Supports 16 connections. EDS file on website
Profinet (server): Supports 1 connection. GSDML file on website
Connectors: Two shielded 8-pin RJ-45 sockets, 10BaseT/100BaseTX
Wiring: Auto-crossover for MDI or MDI-X
IP Address: User-configurable. 128.1.1.100 default static IP address
Data Rate: Auto-negotiated, 10Mbps or 100Mbps
Compliance: IEEE 802.3, 802.3u, 802.3x

Environmental

Operating temperature:
-40 to 70°C (-40 to 158°F). Max temperature derates
-0.625°C per output channel at full load (250mA)
Storage temperature: -40 to 85°C (-40 to 185°F)
Relative humidity: 5 to 95% non-condensing
Power Requirement: 12 to 32V DC (102mA maximum @ 24V)
Isolation: 4-way isolation between I/O channels, network (each port), and power
Peak: 1500V AC, ANSI/ISA-82.01-1988
Continuous: 250V AC, 354V DC
Shock and Vibration Immunity:
Vibration: 4g, per IEC 60068-2-64
Shock: 25g, per IEC 60068-2-27
Electromagnetic Compatibility (EMC) Compliance:
Radiated Emissions: BS EN 61000-6-4, CISPR 16
RFI: BS EN 61000-6-2, IEC 61000-4-3
Conducted RFI: BS EN 61000-6-2, IEC 61000-4-6
ESD: BS EN 61000-6-2, IEC 61000-4-2
EFT: BS EN 61000-6-2, IEC 61000-4-4
Surge Immunity: BS EN 61000-6-2, IEC 61000-4-5
Approvals:
CE compliant. UL/cUL Class I; Div. 2 Zone 2. ATEX Cert. II 3 G Ex nA IIC T4 Gc -40°C < Ta < +80°C

Physical

General: General purpose plastic enclosure for mounting on 35mm “T-type” DIN rail
Case Material: Self-extinguishing polyamide, UL94 V-0 rated, color light gray. General purpose NEMA Type 1 enclosure
Circuit Board: Military grade fire-retardant epoxy glass (IPC-4101/98)
I/O Connectors: Removable plug-in type terminal blocks rated for 12A/250V; AWG #26-12, stranded/solid copper wire
Dimensions:
Width = 22.5mm (0.9 inches)
Length = 114.5mm (4.51 inches)
Depth = 99.0mm (3.90 inches)
Shipping Weight
0.5 pounds (0.22 Kg) packed

 

 

  • i2o® peer-to-peer available for Modbus TCP/IP only
  • 16 solid-state discrete I/O channels (any mix of inputs or outputs)
  • Built-in 10K ohm pull-up resistors for 2/3-wire sensors (contacts, proximity, TTL)
  • Configurable normal/reverse input logic
  • Outputs include built-in read-back capability
  • Easy setup with Windows software via USB
  • Watchdog timer control of failsafe outputs
  • Continuously changing “heart-beat” register validates module operation
  • High-Density 22.5mm wide package with pluggable, front-facing terminals
  • Dual Ethernet 10/100 ports (auto-negotiation) reduce switch port requirements
  • 1500V AC isolation (between I/O, power, and network ports) and surge/transient protection
  • Supports bussed/rail and redundant power
  • -40°C to 70°C wide temperature operation
  • Withstands 25g shock and 4g vibration
  • CE and UL/cUL Class 1 Div 2 Zone 2 approvals
  • ATEX Certified

 

 

How to Communicate with Acromag Series 9xxEN-60xx & XTxxx2-xxx Ethernet/IP Modules from Compact Logix Devices App Note
Communicating with Acromag Series 9xxEN-60xx and XTxxx2-xxx Ethernet/IP Modules from Compact Logix Controllers This document illustrates a procedure for configuring message commands intended for Acromag Busworks® Series Ethernet/IP modules using ladder logic programming software and a Compact Logix Programmable Controller. It is assumed that the user has a working knowledge of ladder logic programming, the...
How to Communicate with Acromag Modbus/TCP Modules from Ignition Software Application Note
Communicating with Ignition Software This document illustrates a procedure for configuring OPC tags intended for Acromag Busworks® Series Modbus/TCP modules using Windows software from Inductive Automation. It is assumed that the user has a working knowledge of OPC, Modbus TCP, and Ignition software. Product Features: BusWorks® Series 9xxEN Modules w/Modbus/TCP BusWorks® Series XT1xx1 Modules w/...
How Ethernet I/O Simplifies Communication Between One PLC and Multiple Remote Locations App Note
This document illustrates using Acromag’s BusWorks® XT Ethernet I/O modules to split one signal from a central control room PLC and control multiple remote locations using Ethernet protocol. Defining the Problem: A customer has multiple remote locations linked over an Ethernet network, each requiring discrete outputs. They all need to be sent the same communication...
How to Connect to Acromag Ethernet I/O Devices App Note
Getting Connected to Acromag Ethernet I/O Devices These instructions summarize the basic steps you will have to take in order to initially connect an Acromag Ethernet I/O product to your Personal Computer (PC) or laptop. To connect an Ethernet device to your PC, consult with your network administrator and either temporarily change the TCP/IP configuration...

Manuals

XT1111 User Manual (Log in to download the file)

XT1112 User Manual (Log in to download the file)

XT1113 User Manual (Log in to download the file)

Drawings & Diagrams

Ethernet XT Series Configuration Software (Log in to download the file)
ESW-MBLIB-DEMO (Log in to download the file)
AMTN-DEMO (Log in to download the file)
ATMX Demo Software (Log in to download the file)
Profinet GSDML Files for XTxxx3-000 Modules (Log in to download the file)
Ethernet IP EDS For XTxxx2-000 Modules (Log in to download the file)
  • Compare

    20RM-16-DIN: 19” rack-mount kit with DIN rail

    • 19" rack-mount kit with DIN rail
    $200
    Select options
  • Compare

    4001 Serial Cables

    5-foot ribbon cable, DB25 male and 26-pin female IDC connectors, for 3B/5B backpanel to Ethernet I/O module connection
    $100
    Select options
  • Compare

    5020-350: Toroidal AC Current Sensor

    • AC Current Sensor to precondition an AC current input signal
    • Highly accurate toroidal instrument transformer that converts an AC current signal to a safe, low level, DC milliampere signal (0 to 11.17mA).
    $50
    Select options
  • Compare

    5035 Series: Ethernet Cables

    • Ethernet straight cable, CAT5
    • Ethernet crossover cable, CAT5E
    • Low EMI Double-Shielded Ethernet Patch Cable
    $45$115
    Select options
  • Compare

    900EN: 5-Port Ethernet Switch

    • 10/100Mbps
    • 15 to 36V DC power supply required
    • Five shielded RJ-45 sockets, 8-pin, 10Base-T / 100Base-TX
    $370
    Select options
  • Compare

    AMTN, AMTX: ActiveX / .NET Controls for Modbus I/O

    • Modbus/TCP or Modbus/RTU
    • These ActiveX / .NET software controls provide a fast, easy way to communicate with any Modbus slave devices connected to your PC.
    • Get your Visual Basic, Visual C, .NET, Excel, or other compatible applications talking Modbus protocol within minutes.
    $285$390
    Select options
  • Compare

    BusWorks XT Connector Kit

    DIN rail bus power/excitation connector kit. Includes one DIN rail bus connector (1005-070), one left-side female connector terminal block (1005-220) and one right side male connector terminal block (1005-221).
    $35
    Select options
  • Compare

    DIN Rail: Type T

    • DIN Rail Strip, Type T
    $25$35
    Select options
  • Compare

    ESW-MBLIB: Ethernet Modbus C Library Software

    • Universal support for five operating systems
    • C source code provided
    • Demo program included
    $0$350
    Select options
  • Compare

    IMC-100A: 10/100BaseTX to 100BaseFX Industrial Media Converter

    • UTP to Fiber Media Converter
    • RJ45 Port Supports Auto MDI/MDI-X Function
     
    $250
    Select options
  • Compare

    PS5R: Slim Line Power Supplies

    • 10W, 15W, 30W, 60W, 90W, 120W, and 240W models
    • Universal Input (85-264V AC / 100-370V DC)
    • Lightweight and compact size
     
    $100$255
    Select options
  • Compare

    Terminal Block Replacements

    • Simplifies wiring connections on Acromag I/O Modules
    • Barrier strip or spring clamp terminal block kits
    • Provide safe and secure wiring connections
    $40$50
    Select options
  • Compare

    USB Isolator

    • USB-powered, USB 2.0 and 1.1 compatible
    • 1500V AC / 2100V DC isolation
    • No drivers required
    This compact, industrial-grade isolator provides a high-voltage isolation barrier between a computer and a connected USB device.    
    $110
    Select options
  • Compare

    USB-to-Ethernet Adapter

    Simplifies configuration of Acromag Ethernet I/O Modules Prevents disruption of existing LANs This device is a USB-to-Ethernet adapter that you can use to communicate with any Acromag Ethernet I/O product for the purpose of setup and re-configuration for your application. It is recommended for initial communication with Acromag Ethernet devices so that you do not have to disrupt your existing network connection.
    $85
    Select options
  • Compare

    XT-SIP: Software Interface Package

    • Software Interface Package for BusWorks XT Series Ethernet I/O modules.
    • Includes configuration software CD-ROM (XT-CONFIG)
      • Isolator (USB-Isolator)
      • Ethernet cable (5035-360)
      • Two USB cables (4001-112, 4001-113)
    • Easy setup and digital calibration via USB with Windows configuration software
    • Download software only from the Software Tab below
    $185
    Select options
  • Compare

    XTA-120V-6: Solid-State Relay Input Modules

    • 6 optocoupler channels
    • 120V AC/DC input with optical isolation
    • Universal 5/12/24V logic output
    $300
    Select options
  • Compare

    XTA-MRNO-6: Mechanical Relay Output Modules

    • 6 digital I/O channels
    •  Universal 5/12/24V logic inputs
    •  Form A, 250V AC / 30V DC @ 5A relay outputs
    $225
    Select options

Additional information

Weight 8 oz
Dimensions 4.5 × 1.5 × 5 in
Part Number

XT1111-000: Modbus/TCP and i2o protocol, XT1112-000: Ethernet/IP protocol, XT1113-000: Profinet protocol

Product Series

BusWorks XT Series

Communication

Ethernet/IP, i2o Peer-to-Peer, Modbus TCP/IP, Profinet

Configuration

USB Configuration, Windows Software Configuration

  • Description

    The XT1110 interfaces discrete I/O signals between measurement and control devices over Ethernet. Channels are individually configurable for input or low-side switched output operation.

    Rugged construction, high density design, and easy USB-to-PC/Windows setup combine for a very effective I/O solution. These units are ideal for remote monitoring, distributed control, or SCADA applications.

    Input/Output Ranges:
    Input: 0-32V DC, TTL thresholds
    Output: 0-32V DC, open-drain, up to 250mA
    Ethernet Communication:
    Modbus TCP/IP, i2o® peer-to-peer available for Modbus TCP/IP only
    Ethernet/IP
    Profinet
    10/100Base-T(X)
    PriorityChannel™ device determinism
    Power Requirement: 12 to 32V DC (2.5W)

    Performance Specifications

    IMPORTANT: To prevent damage or errors from grounded PCs and surges, Acromag strongly recommends use of the USB-ISOLATOR when configuring an XT1000 I/O module.

    USB Interface

    USB Connector:
    Type: USB Mini-B type socket, 5-pin
    Data Rate: 12Mbps. USB v1.1 and 2.0 compatible
    Cable Length: 5.0 meters maximum
    USB Transient Protection: Transient voltage suppression on power and data lines
    Driver: Not required. Uses Windows (HID) drivers

    Input

    Input Type: 16 active-low, buffered inputs, with a common connection. Inputs are tied in tandem to output drains for optional loopback monitoring of output state.
    Input Signal Voltage Range: 0 to 32V DC
    Input Current: 280µA, typical at 32V DC
    Input Signal Threshold: 1.7V typical with 100mV of hysteresis
    Input Resistance: 100K ohms, typical
    Input Response Time: 10ms, nominal

    Output

    Output Type: 16 open-drain, smart, n-channel mosfet switches with a common source connection. Provides low-side (sinking) switching between the load and return.
    Output Voltage: 0 to 32V DC
    Output “ON” Resistance: 0.8 ohms typical, 1.6 ohms maximum
    Output “ON” Current Range: 0 to 250mA DC, continuous (up to 4A total for all 16 channels combined). See Operating Temperature specification for effect of channels at full load. See manual for detailed effects of operating temperature.
    Output Response Time: 10ms, nominal

    Ethernet Communication

    Protocols:
    Modbus TCP/IP, i2o® peer-to-peer available for Modbus TCP/IP only
    Ethernet/IP
    or Profinet, depending on model number
    Ethernet Communication Controller: Innovasic RapID™ Platform with PriorityChannel™ for determinism at the device regardless of network load.
    Modbus TCP/IP (slave): Port 502 reserved. Supports up to 10 sockets
    i2o Peer-to-Peer (master/slave): Can map 4-channel input groups to output groups at two destination IP addresses. Timed or change-of-state updates. Supports GPRS/GSM systems.
    Ethernet/IP (adapter): Supports 16 connections. EDS file on website
    Profinet (server): Supports 1 connection. GSDML file on website
    Connectors: Two shielded 8-pin RJ-45 sockets, 10BaseT/100BaseTX
    Wiring: Auto-crossover for MDI or MDI-X
    IP Address: User-configurable. 128.1.1.100 default static IP address
    Data Rate: Auto-negotiated, 10Mbps or 100Mbps
    Compliance: IEEE 802.3, 802.3u, 802.3x

    Environmental

    Operating temperature:
    -40 to 70°C (-40 to 158°F). Max temperature derates
    -0.625°C per output channel at full load (250mA)
    Storage temperature: -40 to 85°C (-40 to 185°F)
    Relative humidity: 5 to 95% non-condensing
    Power Requirement: 12 to 32V DC (102mA maximum @ 24V)
    Isolation: 4-way isolation between I/O channels, network (each port), and power
    Peak: 1500V AC, ANSI/ISA-82.01-1988
    Continuous: 250V AC, 354V DC
    Shock and Vibration Immunity:
    Vibration: 4g, per IEC 60068-2-64
    Shock: 25g, per IEC 60068-2-27
    Electromagnetic Compatibility (EMC) Compliance:
    Radiated Emissions: BS EN 61000-6-4, CISPR 16
    RFI: BS EN 61000-6-2, IEC 61000-4-3
    Conducted RFI: BS EN 61000-6-2, IEC 61000-4-6
    ESD: BS EN 61000-6-2, IEC 61000-4-2
    EFT: BS EN 61000-6-2, IEC 61000-4-4
    Surge Immunity: BS EN 61000-6-2, IEC 61000-4-5
    Approvals:
    CE compliant. UL/cUL Class I; Div. 2 Zone 2. ATEX Cert. II 3 G Ex nA IIC T4 Gc -40°C < Ta < +80°C

    Physical

    General: General purpose plastic enclosure for mounting on 35mm “T-type” DIN rail
    Case Material: Self-extinguishing polyamide, UL94 V-0 rated, color light gray. General purpose NEMA Type 1 enclosure
    Circuit Board: Military grade fire-retardant epoxy glass (IPC-4101/98)
    I/O Connectors: Removable plug-in type terminal blocks rated for 12A/250V; AWG #26-12, stranded/solid copper wire
    Dimensions:
    Width = 22.5mm (0.9 inches)
    Length = 114.5mm (4.51 inches)
    Depth = 99.0mm (3.90 inches)
    Shipping Weight
    0.5 pounds (0.22 Kg) packed

     

     

  • Features & Benefits

    • i2o® peer-to-peer available for Modbus TCP/IP only
    • 16 solid-state discrete I/O channels (any mix of inputs or outputs)
    • Built-in 10K ohm pull-up resistors for 2/3-wire sensors (contacts, proximity, TTL)
    • Configurable normal/reverse input logic
    • Outputs include built-in read-back capability
    • Easy setup with Windows software via USB
    • Watchdog timer control of failsafe outputs
    • Continuously changing “heart-beat” register validates module operation
    • High-Density 22.5mm wide package with pluggable, front-facing terminals
    • Dual Ethernet 10/100 ports (auto-negotiation) reduce switch port requirements
    • 1500V AC isolation (between I/O, power, and network ports) and surge/transient protection
    • Supports bussed/rail and redundant power
    • -40°C to 70°C wide temperature operation
    • Withstands 25g shock and 4g vibration
    • CE and UL/cUL Class 1 Div 2 Zone 2 approvals
    • ATEX Certified

     

     

  • Tech Papers

    How to Communicate with Acromag Series 9xxEN-60xx & XTxxx2-xxx Ethernet/IP Modules from Compact Logix Devices App Note
    Communicating with Acromag Series 9xxEN-60xx and XTxxx2-xxx Ethernet/IP Modules from Compact Logix Controllers This document illustrates a procedure for configuring message commands intended for Acromag Busworks® Series Ethernet/IP modules using ladder logic programming software and a Compact Logix Programmable Controller. It is assumed that the user has a working knowledge of ladder logic programming, the...
    How to Communicate with Acromag Modbus/TCP Modules from Ignition Software Application Note
    Communicating with Ignition Software This document illustrates a procedure for configuring OPC tags intended for Acromag Busworks® Series Modbus/TCP modules using Windows software from Inductive Automation. It is assumed that the user has a working knowledge of OPC, Modbus TCP, and Ignition software. Product Features: BusWorks® Series 9xxEN Modules w/Modbus/TCP BusWorks® Series XT1xx1 Modules w/...
    How Ethernet I/O Simplifies Communication Between One PLC and Multiple Remote Locations App Note
    This document illustrates using Acromag’s BusWorks® XT Ethernet I/O modules to split one signal from a central control room PLC and control multiple remote locations using Ethernet protocol. Defining the Problem: A customer has multiple remote locations linked over an Ethernet network, each requiring discrete outputs. They all need to be sent the same communication...
    How to Connect to Acromag Ethernet I/O Devices App Note
    Getting Connected to Acromag Ethernet I/O Devices These instructions summarize the basic steps you will have to take in order to initially connect an Acromag Ethernet I/O product to your Personal Computer (PC) or laptop. To connect an Ethernet device to your PC, consult with your network administrator and either temporarily change the TCP/IP configuration...
  • Specs & Data Sheets

    Manuals

    XT1111 User Manual (Log in to download the file)

    XT1112 User Manual (Log in to download the file)

    XT1113 User Manual (Log in to download the file)

    Drawings & Diagrams

  • Software

    Ethernet XT Series Configuration Software (Log in to download the file)
    ESW-MBLIB-DEMO (Log in to download the file)
    AMTN-DEMO (Log in to download the file)
    ATMX Demo Software (Log in to download the file)
    Profinet GSDML Files for XTxxx3-000 Modules (Log in to download the file)
    Ethernet IP EDS For XTxxx2-000 Modules (Log in to download the file)
  • Accessories

    • Compare

      20RM-16-DIN: 19” rack-mount kit with DIN rail

      • 19" rack-mount kit with DIN rail
      $200
      Select options
    • Compare

      4001 Serial Cables

      5-foot ribbon cable, DB25 male and 26-pin female IDC connectors, for 3B/5B backpanel to Ethernet I/O module connection
      $100
      Select options
    • Compare

      5020-350: Toroidal AC Current Sensor

      • AC Current Sensor to precondition an AC current input signal
      • Highly accurate toroidal instrument transformer that converts an AC current signal to a safe, low level, DC milliampere signal (0 to 11.17mA).
      $50
      Select options
    • Compare

      5035 Series: Ethernet Cables

      • Ethernet straight cable, CAT5
      • Ethernet crossover cable, CAT5E
      • Low EMI Double-Shielded Ethernet Patch Cable
      $45$115
      Select options
    • Compare

      900EN: 5-Port Ethernet Switch

      • 10/100Mbps
      • 15 to 36V DC power supply required
      • Five shielded RJ-45 sockets, 8-pin, 10Base-T / 100Base-TX
      $370
      Select options
    • Compare

      AMTN, AMTX: ActiveX / .NET Controls for Modbus I/O

      • Modbus/TCP or Modbus/RTU
      • These ActiveX / .NET software controls provide a fast, easy way to communicate with any Modbus slave devices connected to your PC.
      • Get your Visual Basic, Visual C, .NET, Excel, or other compatible applications talking Modbus protocol within minutes.
      $285$390
      Select options
    • Compare

      BusWorks XT Connector Kit

      DIN rail bus power/excitation connector kit. Includes one DIN rail bus connector (1005-070), one left-side female connector terminal block (1005-220) and one right side male connector terminal block (1005-221).
      $35
      Select options
    • Compare

      DIN Rail: Type T

      • DIN Rail Strip, Type T
      $25$35
      Select options
    • Compare

      ESW-MBLIB: Ethernet Modbus C Library Software

      • Universal support for five operating systems
      • C source code provided
      • Demo program included
      $0$350
      Select options
    • Compare

      IMC-100A: 10/100BaseTX to 100BaseFX Industrial Media Converter

      • UTP to Fiber Media Converter
      • RJ45 Port Supports Auto MDI/MDI-X Function
       
      $250
      Select options
    • Compare

      PS5R: Slim Line Power Supplies

      • 10W, 15W, 30W, 60W, 90W, 120W, and 240W models
      • Universal Input (85-264V AC / 100-370V DC)
      • Lightweight and compact size
       
      $100$255
      Select options
    • Compare

      Terminal Block Replacements

      • Simplifies wiring connections on Acromag I/O Modules
      • Barrier strip or spring clamp terminal block kits
      • Provide safe and secure wiring connections
      $40$50
      Select options
    • Compare

      USB Isolator

      • USB-powered, USB 2.0 and 1.1 compatible
      • 1500V AC / 2100V DC isolation
      • No drivers required
      This compact, industrial-grade isolator provides a high-voltage isolation barrier between a computer and a connected USB device.    
      $110
      Select options
    • Compare

      USB-to-Ethernet Adapter

      Simplifies configuration of Acromag Ethernet I/O Modules Prevents disruption of existing LANs This device is a USB-to-Ethernet adapter that you can use to communicate with any Acromag Ethernet I/O product for the purpose of setup and re-configuration for your application. It is recommended for initial communication with Acromag Ethernet devices so that you do not have to disrupt your existing network connection.
      $85
      Select options
    • Compare

      XT-SIP: Software Interface Package

      • Software Interface Package for BusWorks XT Series Ethernet I/O modules.
      • Includes configuration software CD-ROM (XT-CONFIG)
        • Isolator (USB-Isolator)
        • Ethernet cable (5035-360)
        • Two USB cables (4001-112, 4001-113)
      • Easy setup and digital calibration via USB with Windows configuration software
      • Download software only from the Software Tab below
      $185
      Select options
    • Compare

      XTA-120V-6: Solid-State Relay Input Modules

      • 6 optocoupler channels
      • 120V AC/DC input with optical isolation
      • Universal 5/12/24V logic output
      $300
      Select options
    • Compare

      XTA-MRNO-6: Mechanical Relay Output Modules

      • 6 digital I/O channels
      •  Universal 5/12/24V logic inputs
      •  Form A, 250V AC / 30V DC @ 5A relay outputs
      $225
      Select options
  • Additional information

    Additional information

    Weight 8 oz
    Dimensions 4.5 × 1.5 × 5 in
    Part Number

    XT1111-000: Modbus/TCP and i2o protocol, XT1112-000: Ethernet/IP protocol, XT1113-000: Profinet protocol

    Product Series

    BusWorks XT Series

    Communication

    Ethernet/IP, i2o Peer-to-Peer, Modbus TCP/IP, Profinet

    Configuration

    USB Configuration, Windows Software Configuration