DT336: Current / Voltage Input Four-Wire Dual Transmitter

DT330 series signal conditioners provide two independent I/O channels in a single, space-saving unit. The DT336 model is a four-wire dual transmitter that isolates and converts DC current or low voltage inputs to proportional control signals. Each channel supports DC current or voltage output. An optional DIN rail bus can deliver primary or redundant power to multiple units.

High-voltage isolation separates inputs, outputs, and power from each other. Isolation protects from surges, reduces noise, and eliminates ground loop errors.

Setup and calibration are fast and easy with a convenient USB connection to your PC and Acromag’s Windows configuration software. The Android app enables setup with mobile devices.

Advanced signal processing capabilities, variable range input/output, and convenient USB programming make this instrument very versatile. These transmitters can withstand harsh industrial environments and operate reliably across a wide temperature range with very low drift. They feature RFI, EMI, ESD, EFT, and surge protection plus low radiated emissions.

Performance Specifications

IMPORTANT: To prevent damage or errors from grounded PCs and surges, Acromag strongly recommends use of a USB isolator like Acromag’s USB-Isolator when configuring a DT330 Series transmitter.

USB Interface

USB Connection
Type: USB Mini-B type socket, 5-pin
Data Rate: 12Mbps. USB v1.1 and 2.0 compatible
Maximum cable length: 5.0 meters
Transient voltage suppression on power and data lines.

USB Driver:
Not required. Uses built-in Human Interface Device (HID) USB drivers of the Windows operating system.

Input (two channels)

Default Configuration/Calibration
Input: 4 to 20mA, medium filter
Output: 4 to 20mA

A/D Converters (ADC)
Two 24-bit Sigma Delta ADCs (only 16-bits used)

Input Ranges:
Path A: ±1mA, ±20mA, 0 to 11.17mA, 0-20mA, 4-20mA DC
Path B: ±0.5V, 0-500mV DC
Ambient Temperature Effect: Better than ±80ppm/°C (±0.008%/°C)
Scaling Adjust: Full range
Input Impedance:
Current input: 24.9 ohms
Voltage input: 15M ohms
Input Over-Voltage Protection: Bipolar Transient Voltage Suppression (TVS) and diode clamping
Input Filter: RC filter plus variable digital filter (none, low, medium, high)
Input Bandwidth: -3dB @ 34Hz (no filtering)
Noise Rejection (@ 60Hz, no filter):
Common Mode: 100dB, no filter (120dB, high filter)
Normal Mode: 7dB 60Hz, no filter (>80dB med/high filter)

Output (two channels)

D/A Converters (DAC): Two 16-bit D/A converters
Output Ranges:
±10V (±11V maximum)
±5V (±5.5V maximum)
0 to 10V (11V maximum)
0 to 5V (5.5V maximum)
0 to 20mA (24mA maximum)
4 to 20mA (24mA maximum)
Output Accuracy: ±0.05%, typical. ±0.1%, maximum
Output Load:
Voltage output: 1K ohms minimum
Current output: 0-550 ohms
Output Compliance: 11V, typical

Output Response Time (for step input change)

Time to reach 98% of output value (typical)
No filtering               25 milliseconds
Low filter                   41 milliseconds
Medium filter        140 milliseconds
High filter             1140 milliseconds

Output Ripple: Less than ±0.1% of output span

Environmental

Operating temperature
Operation: -40 to 70°C (-40° to 158°F)
Storage: -40 to 85°C (-40 to 185°F)
Relative humidity: 5 to 95% non-condensing
Power Requirement: 6-32V DC SELV, 1.6W max
Isolation: 1500V AC peak. 250V AC (354V DC) continuous isolation between inputs, outputs, and power (5-way)
Shock and Vibration Immunity:
Vibration: 4g, per IEC 60068-2-6
Shock: 25g, per IEC 60068-2-27

Approvals
CE compliant. Designed for UL/cUL Class I Division 2 Groups ABCD, ATEX / IECEx Zone 2. II 3 G Ex nA IIC T4 Gc -40°C < Ta < +80°C

Electromagnetic Compatibility (EMC) Compliance
Radiated Emissions: BS EN 61000-6-4, CISPR 16
RFI: BS EN 61000-6-2, IEC 61000-4-3
Conducted RFI: BS EN 61000-6-2, IEC 61000-4-6
ESD: BS EN 61000-6-2, IEC 61000-4-2
EFT: BS EN 61000-6-2, IEC 61000-4-4
Surge Immunity: BS EN 61000-6-2, IEC 61000-4-5

Physical

General: General-purpose enclosure designed for mounting on 35mm “T-type” DIN rail
Case Material: Self-extinguishing polyamide, UL94 V-0 rated
I/O Connectors: Removable plug-in terminal blocks rated for 12A/250V; AWG #26-12, stranded or solid copper wire
Dimensions: 17.5 x 114.5 x 99.0 mm (0.7 x 4.51 x 3.90 inches)
Unit weight: 0.16 kg (0.35 pounds)
Shipping Weight: 0.22 kg (0.5 pounds) packed

Additional information