XT1530: Analog Output & Digital I/O Ethernet Modules

The XT1530 interfaces analog output and discrete I/O signals between measurement and control devices over Ethernet. Discrete I/O are individually configurable for input or high-side switched output operation.

Rugged construction, high density design, and easy USB-to-PC/Windows setup combine for a very effective I/O solution. These units are ideal for remote monitoring, distributed control, or SCADA applications.

Analog Output Ranges: 0-20mA DC, 4-20mA DC
Discrete Input/Output Ranges:
Input: 0-32V DC, TTL thresholds
Output: 0-32V DC, open-source, up to 250mA
Ethernet Communication:
Modbus TCP/IP, i2o® peer-to-peer available for Modbus TCP/IP only
Ethernet/IP
Profinet
10/100Base-T(X)
PriorityChannel™ device determinism
Power Requirement: 12 to 32V DC (2.8W)

Performance Specifications

IMPORTANT: To prevent damage or errors from grounded PCs and surges, Acromag strongly recommends use of the USB-ISOLATOR when configuring an XT1000 I/O module.

USB Interface

USB Connector:
Type: USB Mini-B type socket, 5-pin
Data Rate: 12Mbps. USB v1.1 and 2.0 compatible
Cable Length: 5.0 meters maximum
USB Transient Protection: Transient voltage suppression on power and data lines
Driver: Not required. Uses Windows (HID) drivers

Analog Output

Configuration: 4 output channels, each with a 16-bit D/A converter
Output Type: 0-20mA DC or 4-20mA DC, configurable by channel
Accuracy: Better than ±0.1% of span
Output Excitation: Separate inputs for 12V (10-15V) and 24V (20-28V) power sources. Diode-coupled to support redundancy.

Discrete Input

Input Type: 4 active-high, buffered inputs, with a common connection. Inputs are tied in tandem to output drains for optional loopback monitoring of output state.
Input Signal Voltage Range: 0 to 32V DC
Input Current: 280μA, typical at 32V DC
Input Signal Threshold: 1.7V DC typical with100mV of hysteresis
Input Resistance: 10K ohms, typical
Input Response Time: 10ms, nominal

Discrete Output

Output Type: 4 open-source, smart, p-channel mosfet switches with a common drain connection. Provides high-side (sourcing) switching between the load and return.
Output Signal Voltage Range: 0 to 32V DC. 6-32V excitation source required.
Output “ON” Resistance: 0.5 ohms typical, 1.0 ohms maximum
Output “ON” Current Range: 0 to 250mA DC, continuous (up to 1A total for all 4 channels combined)
Output Response Time: 10ms, nominal

Ethernet Communication

Protocols:
Modbus TCP/IP, i2o® peer-to-peer available for Modbus TCP/IP only
Ethernet/IP
or Profinet, depending on model number
Ethernet Communication Controller: Innovasic RapID™ Platform with PriorityChannel™ for determinism at the device regardless of network load.
Modbus TCP/IP (slave): Port 502 reserved. Supports up to 10 sockets.
i2o Peer-to-Peer (master/slave): Can map 4-channel input groups to output groups at two destination IP addresses. Timed or change-of-state updates. Supports GPRS/GSM systems.
Ethernet/IP (adapter): Supports 16 connections. EDS file on website
Profinet (server): Supports 1 connection. GSDML file on website
Connectors: Two shielded 8-pin RJ-45 sockets, 10BaseT/100BaseTX
Wiring: Auto-crossover for MDI or MDI-X
IP Address: User-configurable. 192.168.1.100 default static IP address
Data Rate: Auto-negotiated, 10Mbps or 100Mbps
Compliance: IEEE 802.3, 802.3u, 802.3x

Environmental

Operating Temperature: -40 to 60°C (-40 to 140°F)
Storage Temperature: -40 to 85°C (-40 to 185°F)
Relative Humidity: 5 to 95% non-condensing
Power Requirement: 12 to 32V DC (110mA maximum @ 24V)
Isolation: I/O channels (as a group), network (each port), and power circuits isolated from each other
Peak: 1500V AC, ANSI/ISA-82.01-1988
Continuous: 250V AC, 354V DC
MTBF: 445,034 hrs. at 25°C; 335,836 hrs. at 40°C
Shock Immunity: 25g, per IEC 60068-2-27
Vibration Immunity: 4g, per IEC 60068-2-64
Approvals: CE compliant. UL/cUL listings. ATEX Certified. Designed for Class I; Division 2; Groups ABCD; Zone 2. ATEX II 3 G Ex nA IIC T4 Gc -40°C < Ta < 80°C
Electromagnetic Compatibility (EMC) Compliance
Radiated Emissions: BS EN 61000-6-4, CISPR 16
RFI: BS EN 61000-6-2, IEC 61000-4-3
Conducted RFI: BS EN 61000-6-2, IEC 61000-4-6
ESD: BS EN 61000-6-2, IEC 61000-4-2
EFT: BS EN 61000-6-2, IEC 61000-4-4
Surge Immunity: BS EN 61000-6-2, IEC 61000-4-5

Physical

General: General purpose plastic enclosure for mounting on 35mm “T-type” DIN rail
Case Material: Self-extinguishing polyamide, UL94 V-0 rated, color light gray. General purpose NEMA Type 1 enclosure
Circuit Board: Military grade fire-retardant epoxy glass (IPC-4101/98)
I/O Connectors: Removable plug-in type terminal blocks rated for 12A/250V; AWG #26-12, stranded/solid copper wire
Dimensions:
Width = 22.5mm (0.9 inches)
Length = 114.5mm (4.51 inches)
Depth = 99.0mm (3.90 inches)
Shipping Weight: 0.5 pounds (0.22 Kg) packed

Additional information