TT335: Isolated RTD Input, DC Local/Bus Power Transmitter

TT335: Isolated RTD Input, DC Local/Bus Power Transmitter Description

The TT335 model is a space-saving four-wire transmitter that isolates and converts an RTD sensor input to a proportional control signal. DC current and voltage output are both supported on a single model. An optional DIN rail bus can deliver primary or redundant power to multiple units without wiring.

High-voltage isolation separates the input from the output circuit. Isolation protects from surges, reduces noise, and eliminates ground loop errors.

Setup and calibration are fast and easy with a convenient USB connection to your PC and Acromag’s Windows configuration software.

Advanced signal processing capabilities, variable range input, and convenient USB programming make this instrument a very versatile temperature measurement device. These transmitters can withstand harsh industrial environments and operate reliably across a wide temperature range with very low drift. They feature RFI, EMI, ESD, EFT, and surge protection plus low radiated emissions.

Performance Specifications

IMPORTANT: To prevent damage or errors from grounded PCs and surges, Acromag strongly recommends the use of their USB-ISOLATOR when configuring a TT330 Series transmitter.

USB Interface

USB Connector: USB Mini-B type socket, 5-pin.

USB Data Rate: 12Mbps. USB v1.1 and 2.0 compatible.

Maximum Cable Length: 5.0 meters.

USB Transient Protection: Transient voltage suppression on power and data lines.

Driver: Not required. Uses Windows HID drivers.

Input

Default Configuration
100Ω Pt RTD, α=0.00385, -200 to 850°C input, 4-20mA output, upscale break detect, medium filter.

Input Configuration
Two- three- or four-wire sensor input connections.
Programs in °C, °F, °K, or ohmic integer values only.

Input Ranges
Input Type                                   Range                 Accuracy
Pt 100Ω                                     -200 to 850°C           ±0.25°C
Pt 200Ω                                     -200 to 850°C           ±0.30°C
Pt 500Ω                                     -200 to 850°C           ±0.50°C
Pt 1000Ω                                   -200 to 850°C           ±1.00°C
Ni 120Ω (Minco 7-120)            -80 to 320°C          ±0.08°C
Cu 10Ω (Minco 16-9)             -200 to 270°C           ±1.00°C
Linear Resistance                         0 to 250Ω            ±0.05Ω
Linear Resistance                         0 to 450Ω            ±0.10Ω
Linear Resistance                         0 to 900Ω            ±0.90Ω
Linear Resistance                         0 to 2250Ω          ±2.25Ω
Linear Resistance                         0 to 4500Ω          ±4.50Ω

Input Scaling Adjust
Zero: 0 to 95% of range, typical.
Full scale: 5 to 100% of full scale range, typical.

Lead Break (Sensor Burnout) Detection: Configurable for either upscale or downscale.

Output

Output Range:
Range                    Over-Range                 Resolution
±10V                            ±10.5V                       1 part in 62558
±5V                               ±5.25V                      1 part in 31278
0 to 10V              –0.5527 to +10.5V        1 part in 59293
0 to 5V              –0.27634 to +5.25V        1 part in 60414
±20mA                        ±21mA                      1 part in 62400
0 to 20mA          –1.1054 to 21mA          1 part in 58732
4 to 20mA          –1.1054 to 21mA          1 part in 46984

Output Accuracy: Better than ±0.05% of span, typical (±0.1% max.) for for nominal input spans. Includes the effects of repeatability, terminal point conformity, and linearization, but does not include sensor error.

Output Load
Voltage output: 1K ohms minimum.
Current output: 0-525 ohms.

Output Response Time (for step input change)
No filter: 32ms.
Low filter: 50ms.
Medium filter: 160ms.
High filter: 1210ms.

Output Ambient Temperature Drift: Better than ±80ppm/°C (±0.0080%/°C).

Environmental

Operating temperature: -40 to 80°C (-40° to 176°F).

Storage temperature: -40 to 85°C (-40 to 185°F).

Relative humidity: 5 to 95% non-condensing.

Power requirement: 12-32V DC SELV (Safety Extra Low Voltage), 1.3W maximum.

Isolation: 1500V AC peak. 250V AC (354V DC) continuous isolation between input, output, and power (3-way),

Shock and Vibration Immunity
Vibration: 4g, per IEC 60068-2-6.
Shock: 25g, per IEC 60068-2-27.

Electromagnetic Compatibility (EMC) Compliance
Radiated Emissions: BS EN 61000-6-4, CISPR 16.
RFI: BS EN 61000-6-2, IEC 61000-4-3.
Conducted RFI: BS EN 61000-6-2, IEC 61000-4-6.
ESD: BS EN 61000-6-2, IEC 61000-4-2.
EFT: BS EN 61000-6-2, IEC 61000-4-4.
Surge Immunity: BS EN 61000-6-2, IEC 61000-4-5.

Approvals: CE compliant. Designed for UL/cUL Class I Division 2 Groups ABCD. ATEX / IECEx certified Zone 2.

Physical

General: General-purpose enclosure designed for mounting on 35mm “T-type” DIN rail.

Case Material: Self-extinguishing polyamide, UL94 V-0 rated, color light gray. General-purpose NEMA Type 1 enclosure.

I/O Connectors: Removable plug-in terminal blocks rated for 12A/250V; AWG #26-12, stranded or solid copper wire.

Dimensions: 17.5 x 114.5 x 99.0 mm (0.7 x 4.51 x 3.90 inches).

Shipping Weight: 0.22 kg (0.5 pounds) packed.

Additional information