XT1120: 16-Channel Discrete Ethernet I/O Modules with Sourcing Outputs
Please sign in or register to see model options and to add products to your cart.
Product short description:
- Input: 0-32V DC, TTL thresholds
- Output: 0-32V DC, open-drain, up to 300mA
- Power Requirement: 12 to 32V DC (2.5W)
- Modbus TCP/IP, Ethernet/IP, Profinet
- i2o® peer-to-peer available for Modbus TCP/IP only
The XT1120 interfaces discrete I/O signals between measurement and control devices over Ethernet. Channels are individually configurable for input or high-side switched output operation.
- Description
- Features & Benefits
- Tech Papers
- Specs & Data Sheets
- Software
- Accessories
- Additional information
The XT1120 interfaces discrete I/O signals between measurement and control devices over Ethernet. Channels are individually configurable for input or high-side switched output operation.
Rugged construction, high density design, and easy USB-to-PC/Windows setup combine for a very effective I/O solution. These units are ideal for remote monitoring, distributed control, or SCADA applications.
Input/Output Ranges:
Input: 0-32V DC, TTL thresholds
Output: 0-32V DC, open-source, up to 300mA
Ethernet Communication:
Modbus TCP/IP, i2o® peer-to-peer available for Modbus TCP/IP only
Ethernet/IP
Profinet
10/100Base-T(X)
PriorityChannel™ device determinism
Power Requirement: 12 to 32V DC (2.5W)
Performance Specifications
IMPORTANT: To prevent damage or errors from grounded PCs and surges, Acromag strongly recommends use of the USB-ISOLATOR when configuring an XT1000 I/O module.
USB Interface
USB Connector:
Type: USB Mini-B type socket, 5-pin
Data Rate: 12Mbps. USB v1.1 and 2.0 compatible
Cable Length: 5.0 meters maximum
USB Transient Protection: Transient voltage suppression on power and data lines
Driver: Not required. Uses Windows (HID) drivers
Input
Input Type: 16 active-high, buffered inputs, with a common connection. Inputs are tied in tandem to output drains for optional loopback monitoring of output state.
Input Signal Voltage Range: 0 to 32V DC
Input Current: 280µA, typical at 32V DC
Input Signal Threshold: 1.7V typical with 100mV of hysteresis
Input Resistance: 100K ohms, typical
Input Response Time: 10ms, nominal
Output
Output Type: 16 open-source, smart, p-channel mosfet switches with a common drain connection. Provides high-side (sourcing) switching between excitation and load.
Output Voltage: 0 to 32V DC
Output “ON” Resistance: 0.8 ohms typical, 1.6 ohms maximum
Output “ON” Current Range: 0 to 300mA DC, continuous (up to 4.8A total for all 16 channels combined). See Operating Temperature specification for effect of channels at full load. See manual for detailed effects of operating temperature.
Output Response Time: 10ms, nominal
Ethernet Communication
Protocols:
Modbus TCP/IP, i2o® peer-to-peer available for Modbus TCP/IP only
Ethernet/IP
or Profinet, depending on model number
Ethernet Communication Controller: Innovasic RapID™ Platform with PriorityChannel™ for determinism at the device regardless of network load.
Modbus TCP/IP (slave): Port 502 reserved. Supports up to 10 sockets
i2o Peer-to-Peer (master/slave): Can map 4-channel input groups to output groups at two destination IP addresses. Timed or change-of-state updates. Supports GPRS/GSM systems.
Ethernet/IP (adapter): Supports 16 connections. EDS file on website
Profinet (server): Supports 1 connection. GSDML file on website
Connectors: Two shielded 8-pin RJ-45 sockets, 10BaseT/100BaseTX
Wiring: Auto-crossover for MDI or MDI-X
IP Address: User-configurable. 128.1.1.100 default static IP address
Data Rate: Auto-negotiated, 10Mbps or 100Mbps
Compliance: IEEE 802.3, 802.3u, 802.3x
Environmental
Operating temperature:
-40 to 70°C (-40 to 158°F). Max temperature derates
-0.625°C per output channel at full load (250mA)
Storage temperature: -40 to 85°C (-40 to 185°F)
Relative humidity: 5 to 95% non-condensing
Power Requirement: 12 to 32V DC (95mA maximum @ 24V)
Isolation:
4-way isolation between I/O channels, network (each port), and power.
Peak: 1500V AC, ANSI/ISA-82.01-1988
Continuous: 250V AC, 354V DC
Shock and Vibration Immunity:
Vibration: 4g, per IEC 60068-2-64
Shock: 25g, per IEC 60068-2-27
Electromagnetic Compatibility (EMC) Compliance:
Radiated Emissions: BS EN 61000-6-4, CISPR 16
RFI: BS EN 61000-6-2, IEC 61000-4-3
Conducted RFI: BS EN 61000-6-2, IEC 61000-4-6
ESD: BS EN 61000-6-2, IEC 61000-4-2
EFT: BS EN 61000-6-2, IEC 61000-4-4
Surge Immunity: BS EN 61000-6-2, IEC 61000-4-5
Approvals:
CE compliant. UL/cUL Class I; Div. 2 Zone 2. ATEX Cert. II 3 G Ex nA IIC T4 Gc -40°C < Ta < +80°C
Physical
General: General purpose plastic enclosure for mounting on 35mm “T-type” DIN rail
Case Material: Self-extinguishing polyamide, UL94 V-0 rated, color light gray. General purpose NEMA Type 1 enclosure
Circuit Board: Military grade fire-retardant epoxy glass (IPC-4101/98)
I/O Connectors: Removable plug-in type terminal blocks rated for 12A/250V; AWG #26-12, stranded/solid copper wire
Dimensions:
Width = 22.5mm (0.9 inches)
Length = 114.5mm (4.51 inches)
Depth = 99.0mm (3.90 inches)
Shipping Weight: 0.5 pounds (0.22 Kg) packed
- i2o® peer-to-peer available for Modbus TCP/IP only
- 16 solid-state discrete I/O channels (any mix of inputs or outputs)
- Built-in 10K ohm pull-up resistors for 2/3-wire sensors (contacts, proximity, TTL)
- Configurable normal/reverse input logic
- Open-drain outputs switch up to 300mA each and include built-in read-back capability
- Easy setup with Windows software via USB
- Watchdog timer control of failsafe outputs
- Continuously changing “heart-beat” register validates module operation
- High-Density 22.5mm wide package with pluggable, front-facing terminals
- Dual Ethernet 10/100 ports (auto-negotiation) reduce switch port requirements
- 1500V AC isolation (between I/O, power, and network ports) and surge/transient protection
- Supports bussed/rail and redundant power
- -40°C to 70°C wide temperature operation
- Withstands 25g shock and 4g vibration
- CE and UL/cUL Class 1 Div 2 Zone 2 approvals.
- ATEX Certified.
Specifications
Manuals
Brochure
Drawings & Diagrams
-
4001 Serial Cables
5-foot ribbon cable, DB25 male and 26-pin female IDC connectors, for 3B/5B backpanel to Ethernet I/O module connection$100Select options -
5020-350: Toroidal AC Current Sensor
- AC Current Sensor to precondition an AC current input signal
- Highly accurate toroidal instrument transformer that converts an AC current signal to a safe, low level, DC milliampere signal (0 to 11.17mA).
$50Select options -
900EN: 5-Port Ethernet Switch
- 10/100Mbps
- 15 to 36V DC power supply required
- Five shielded RJ-45 sockets, 8-pin, 10Base-T / 100Base-TX
$350Select options -
AMTN, AMTX: ActiveX / .NET Controls for Modbus I/O
- Modbus/TCP or Modbus/RTU
- These ActiveX / .NET software controls provide a fast, easy way to communicate with any Modbus slave devices connected to your PC.
- Get your Visual Basic, Visual C, .NET, Excel, or other compatible applications talking Modbus protocol within minutes.
$270 – $370Select options -
BusWorks XT Connector Kit
DIN rail bus power/excitation connector kit. Includes one DIN rail bus connector (1005-070), one left-side female connector terminal block (1005-220) and one right side male connector terminal block (1005-221).$30Select options -
ESW-MBLIB: Ethernet Modbus C Library Software
- Universal support for five operating systems
- C source code provided
- Demo program included
$0 – $350Select options -
IMC-100A: 10/100BaseTX to 100BaseFX Industrial Media Converter
- UTP to Fiber Media Converter
- RJ45 Port Supports Auto MDI/MDI-X Function
$250Select options -
PS5R: Slim Line Power Supplies
- 10W, 15W, 30W, 60W, 90W, 120W, and 240W models
- Universal Input (85-264V AC / 100-370V DC)
- Lightweight and compact size
$100 – $255Select options -
Terminal Block Replacements
- Simplifies wiring connections on Acromag I/O Modules
- Barrier strip or spring clamp terminal block kits
- Provide safe and secure wiring connections
$35 – $45Select options -
USB Isolator
- USB-powered, USB 2.0 and 1.1 compatible
- 1500V AC / 2100V DC isolation
- No drivers required
$110Select options -
USB-to-Ethernet Adapter
Simplifies configuration of Acromag Ethernet I/O Modules Prevents disruption of existing LANs This device is a USB-to-Ethernet adapter that you can use to communicate with any Acromag Ethernet I/O product for the purpose of setup and re-configuration for your application. It is recommended for initial communication with Acromag Ethernet devices so that you do not have to disrupt your existing network connection.$85Select options -
XT-SIP: Software Interface Package
- Software Interface Package for BusWorks XT Series Ethernet I/O modules.
- Includes configuration software CD-ROM (XT-CONFIG)
- Isolator (USB-Isolator)
- Ethernet cable (5035-360)
- Two USB cables (4001-112, 4001-113)
- Easy setup and digital calibration via USB with Windows configuration software
- Download software only from the Software Tab below
$185Select options -
XTA-120V-6: Solid-State Relay Input Modules
- 6 optocoupler channels
- 120V AC/DC input with optical isolation
- Universal 5/12/24V logic output
$250Select options -
XTA-MRNO-6: Mechanical Relay Output Modules
- 6 digital I/O channels
- Universal 5/12/24V logic inputs
- Form A, 250V AC / 30V DC @ 5A relay outputs
$195Select options
Additional information
Weight | 8 oz |
---|---|
Dimensions | 4.5 × 1.5 × 5 in |
Part Number | XT1121-000: Modbus TCP/IP and i2o Discrete, XT1122-000: Ethernet/IP I/O Module, XT1123-000: Profinet I/O Module |
Product Series | BusWorks XT Series |
Communication | Ethernet/IP, i2o Peer-to-Peer, Modbus TCP/IP, Profinet |
Configuration | USB Configuration, Windows Software Configuration |
-
Description
The XT1120 interfaces discrete I/O signals between measurement and control devices over Ethernet. Channels are individually configurable for input or high-side switched output operation.
Rugged construction, high density design, and easy USB-to-PC/Windows setup combine for a very effective I/O solution. These units are ideal for remote monitoring, distributed control, or SCADA applications.
Input/Output Ranges:
Input: 0-32V DC, TTL thresholds
Output: 0-32V DC, open-source, up to 300mA
Ethernet Communication:
Modbus TCP/IP, i2o® peer-to-peer available for Modbus TCP/IP only
Ethernet/IP
Profinet
10/100Base-T(X)
PriorityChannel™ device determinism
Power Requirement: 12 to 32V DC (2.5W)Performance Specifications
IMPORTANT: To prevent damage or errors from grounded PCs and surges, Acromag strongly recommends use of the USB-ISOLATOR when configuring an XT1000 I/O module.
USB Interface
USB Connector:
Type: USB Mini-B type socket, 5-pin
Data Rate: 12Mbps. USB v1.1 and 2.0 compatible
Cable Length: 5.0 meters maximum
USB Transient Protection: Transient voltage suppression on power and data lines
Driver: Not required. Uses Windows (HID) driversInput
Input Type: 16 active-high, buffered inputs, with a common connection. Inputs are tied in tandem to output drains for optional loopback monitoring of output state.
Input Signal Voltage Range: 0 to 32V DC
Input Current: 280µA, typical at 32V DC
Input Signal Threshold: 1.7V typical with 100mV of hysteresis
Input Resistance: 100K ohms, typical
Input Response Time: 10ms, nominalOutput
Output Type: 16 open-source, smart, p-channel mosfet switches with a common drain connection. Provides high-side (sourcing) switching between excitation and load.
Output Voltage: 0 to 32V DC
Output “ON” Resistance: 0.8 ohms typical, 1.6 ohms maximum
Output “ON” Current Range: 0 to 300mA DC, continuous (up to 4.8A total for all 16 channels combined). See Operating Temperature specification for effect of channels at full load. See manual for detailed effects of operating temperature.
Output Response Time: 10ms, nominalEthernet Communication
Protocols:
Modbus TCP/IP, i2o® peer-to-peer available for Modbus TCP/IP only
Ethernet/IP
or Profinet, depending on model number
Ethernet Communication Controller: Innovasic RapID™ Platform with PriorityChannel™ for determinism at the device regardless of network load.
Modbus TCP/IP (slave): Port 502 reserved. Supports up to 10 sockets
i2o Peer-to-Peer (master/slave): Can map 4-channel input groups to output groups at two destination IP addresses. Timed or change-of-state updates. Supports GPRS/GSM systems.
Ethernet/IP (adapter): Supports 16 connections. EDS file on website
Profinet (server): Supports 1 connection. GSDML file on website
Connectors: Two shielded 8-pin RJ-45 sockets, 10BaseT/100BaseTX
Wiring: Auto-crossover for MDI or MDI-X
IP Address: User-configurable. 128.1.1.100 default static IP address
Data Rate: Auto-negotiated, 10Mbps or 100Mbps
Compliance: IEEE 802.3, 802.3u, 802.3xEnvironmental
Operating temperature:
-40 to 70°C (-40 to 158°F). Max temperature derates
-0.625°C per output channel at full load (250mA)
Storage temperature: -40 to 85°C (-40 to 185°F)
Relative humidity: 5 to 95% non-condensing
Power Requirement: 12 to 32V DC (95mA maximum @ 24V)
Isolation:
4-way isolation between I/O channels, network (each port), and power.
Peak: 1500V AC, ANSI/ISA-82.01-1988
Continuous: 250V AC, 354V DC
Shock and Vibration Immunity:
Vibration: 4g, per IEC 60068-2-64
Shock: 25g, per IEC 60068-2-27
Electromagnetic Compatibility (EMC) Compliance:
Radiated Emissions: BS EN 61000-6-4, CISPR 16
RFI: BS EN 61000-6-2, IEC 61000-4-3
Conducted RFI: BS EN 61000-6-2, IEC 61000-4-6
ESD: BS EN 61000-6-2, IEC 61000-4-2
EFT: BS EN 61000-6-2, IEC 61000-4-4
Surge Immunity: BS EN 61000-6-2, IEC 61000-4-5
Approvals:
CE compliant. UL/cUL Class I; Div. 2 Zone 2. ATEX Cert. II 3 G Ex nA IIC T4 Gc -40°C < Ta < +80°CPhysical
General: General purpose plastic enclosure for mounting on 35mm “T-type” DIN rail
Case Material: Self-extinguishing polyamide, UL94 V-0 rated, color light gray. General purpose NEMA Type 1 enclosure
Circuit Board: Military grade fire-retardant epoxy glass (IPC-4101/98)
I/O Connectors: Removable plug-in type terminal blocks rated for 12A/250V; AWG #26-12, stranded/solid copper wire
Dimensions:
Width = 22.5mm (0.9 inches)
Length = 114.5mm (4.51 inches)
Depth = 99.0mm (3.90 inches)
Shipping Weight: 0.5 pounds (0.22 Kg) packed -
Features & Benefits
- i2o® peer-to-peer available for Modbus TCP/IP only
- 16 solid-state discrete I/O channels (any mix of inputs or outputs)
- Built-in 10K ohm pull-up resistors for 2/3-wire sensors (contacts, proximity, TTL)
- Configurable normal/reverse input logic
- Open-drain outputs switch up to 300mA each and include built-in read-back capability
- Easy setup with Windows software via USB
- Watchdog timer control of failsafe outputs
- Continuously changing “heart-beat” register validates module operation
- High-Density 22.5mm wide package with pluggable, front-facing terminals
- Dual Ethernet 10/100 ports (auto-negotiation) reduce switch port requirements
- 1500V AC isolation (between I/O, power, and network ports) and surge/transient protection
- Supports bussed/rail and redundant power
- -40°C to 70°C wide temperature operation
- Withstands 25g shock and 4g vibration
- CE and UL/cUL Class 1 Div 2 Zone 2 approvals.
- ATEX Certified.
-
Tech Papers
How to Communicate with Acromag Modbus/TCP Modules from Ignition Software Application NoteCommunicating with Ignition Software This document illustrates a procedure for configuring OPC tags intended for Acromag Busworks® Series Modbus/TCP modules using Windows software from Inductive Automation. It is assumed that the user has a working knowledge of OPC, Modbus TCP, and Ignition software. Product Features: BusWorks® Series 9xxEN Modules w/Modbus/TCP BusWorks® Series XT1xx1 Modules w/...How to Remotely Monitor Wind Turbines Application NoteRemote Monitoring of Wind Turbines Defining the Problem: A large utility company has a requirement to monitor multiple data points on a wind turbine. The turbine head is 300 feet above the ground. The data must be sent to a ground station, saved to a data logger, and displayed on a Honeywell chart recorder. The...How to Connect to Acromag Ethernet I/O Devices Application NoteGetting Connected to Acromag Ethernet I/O Devices These instructions summarize the basic steps you will have to take in order to initially connect an Acromag Ethernet I/O product to your Personal Computer (PC) or laptop. To connect an Ethernet device to your PC, consult with your network administrator and either temporarily change the TCP/IP configuration... -
Specs & Data Sheets
Specifications
Manuals
Brochure
Drawings & Diagrams
-
Software
Ethernet XT Series Configuration Software (Log in to download the file)Ethernet IP EDS For XTxxx2-000 Modules (Log in to download the file)Profinet GSDML Files for XTxxx3-000 Modules (Log in to download the file)ESW-MBLIB-DEMO (Log in to download the file)AMTN-DEMO (Log in to download the file)ATMX Demo Software (Log in to download the file) -
Accessories
-
4001 Serial Cables
5-foot ribbon cable, DB25 male and 26-pin female IDC connectors, for 3B/5B backpanel to Ethernet I/O module connection$100Select options -
5020-350: Toroidal AC Current Sensor
- AC Current Sensor to precondition an AC current input signal
- Highly accurate toroidal instrument transformer that converts an AC current signal to a safe, low level, DC milliampere signal (0 to 11.17mA).
$50Select options -
900EN: 5-Port Ethernet Switch
- 10/100Mbps
- 15 to 36V DC power supply required
- Five shielded RJ-45 sockets, 8-pin, 10Base-T / 100Base-TX
$350Select options -
AMTN, AMTX: ActiveX / .NET Controls for Modbus I/O
- Modbus/TCP or Modbus/RTU
- These ActiveX / .NET software controls provide a fast, easy way to communicate with any Modbus slave devices connected to your PC.
- Get your Visual Basic, Visual C, .NET, Excel, or other compatible applications talking Modbus protocol within minutes.
$270 – $370Select options -
BusWorks XT Connector Kit
DIN rail bus power/excitation connector kit. Includes one DIN rail bus connector (1005-070), one left-side female connector terminal block (1005-220) and one right side male connector terminal block (1005-221).$30Select options -
ESW-MBLIB: Ethernet Modbus C Library Software
- Universal support for five operating systems
- C source code provided
- Demo program included
$0 – $350Select options -
IMC-100A: 10/100BaseTX to 100BaseFX Industrial Media Converter
- UTP to Fiber Media Converter
- RJ45 Port Supports Auto MDI/MDI-X Function
$250Select options -
PS5R: Slim Line Power Supplies
- 10W, 15W, 30W, 60W, 90W, 120W, and 240W models
- Universal Input (85-264V AC / 100-370V DC)
- Lightweight and compact size
$100 – $255Select options -
Terminal Block Replacements
- Simplifies wiring connections on Acromag I/O Modules
- Barrier strip or spring clamp terminal block kits
- Provide safe and secure wiring connections
$35 – $45Select options -
USB Isolator
- USB-powered, USB 2.0 and 1.1 compatible
- 1500V AC / 2100V DC isolation
- No drivers required
$110Select options -
USB-to-Ethernet Adapter
Simplifies configuration of Acromag Ethernet I/O Modules Prevents disruption of existing LANs This device is a USB-to-Ethernet adapter that you can use to communicate with any Acromag Ethernet I/O product for the purpose of setup and re-configuration for your application. It is recommended for initial communication with Acromag Ethernet devices so that you do not have to disrupt your existing network connection.$85Select options -
XT-SIP: Software Interface Package
- Software Interface Package for BusWorks XT Series Ethernet I/O modules.
- Includes configuration software CD-ROM (XT-CONFIG)
- Isolator (USB-Isolator)
- Ethernet cable (5035-360)
- Two USB cables (4001-112, 4001-113)
- Easy setup and digital calibration via USB with Windows configuration software
- Download software only from the Software Tab below
$185Select options -
XTA-120V-6: Solid-State Relay Input Modules
- 6 optocoupler channels
- 120V AC/DC input with optical isolation
- Universal 5/12/24V logic output
$250Select options -
XTA-MRNO-6: Mechanical Relay Output Modules
- 6 digital I/O channels
- Universal 5/12/24V logic inputs
- Form A, 250V AC / 30V DC @ 5A relay outputs
$195Select options
-
Additional information
Additional information
Weight 8 oz Dimensions 4.5 × 1.5 × 5 in Part Number XT1121-000: Modbus TCP/IP and i2o Discrete, XT1122-000: Ethernet/IP I/O Module, XT1123-000: Profinet I/O Module
Product Series BusWorks XT Series
Communication Ethernet/IP, i2o Peer-to-Peer, Modbus TCP/IP, Profinet
Configuration USB Configuration, Windows Software Configuration
Please login to submit this form.