XT1540: Analog Output & Digital I/O Ethernet Modules
Please sign in or register to see model options and to add products to your cart.
Product short description:
- 8 Analog DC Voltage Outputs ±10V (calibrated), ±5V (sub-range)
- 4 Discrete Voltage I/O Channels 0-32V DC
- 12 to 32V DC Power (2.8W)
- Modbus TCP/IP, Ethernet/IP, Profinet
- i2o® peer-to-peer available for Modbus TCP/IP only
The XT1540 interfaces analog output and discrete I/O signals between measurement and control devices over Ethernet. Discrete I/O are individually configurable for input or high-side switched output operation.
- Description
- Features & Benefits
- Tech Papers
- Specs & Data Sheets
- Software
- Accessories
- Additional information
XT1540: Analog Output & Digital I/O Ethernet Modules Description
The XT1540 interfaces analog output and discrete I/O signals between measurement and control devices over Ethernet.
Discrete I/O are individually configurable for input or high-side switched output operation.
Rugged construction, high density design, and easy USB-to-PC/Windows setup combine for a very effective I/O solution.
These units are ideal for remote monitoring, distributed control, or SCADA applications.
Analog Output Ranges: ±5V, ±10V DC.
Discrete Input/Output Ranges
Input: 0-32V DC, TTL thresholds.
Output: 0-32V DC, open-source, up to 250mA.
Ethernet Communication
Modbus TCP/IP, i2o® peer-to-peer available for Modbus TCP/IP only.
Ethernet/IP
Profinet
10/100Base-T(X)
PriorityChannel™ device determinism
Power Requirement: 12 to 32V DC (2.8W).
Learn more about the Ethernet XT Series and view all models >
XT1540: Analog Output & Digital I/O Ethernet Modules Performance Specifications
IMPORTANT: To prevent damage or errors from grounded PCs and surges, Acromag strongly recommends use of the USB-ISOLATOR when configuring an XT1000 I/O module.
USB Interface
USB Connector
Type: USB Mini-B type socket, 5-pin.
Data Rate: 12Mbps. USB v1.1 and 2.0 compatible.
Cable Length: 5.0 meters maximum.
USB Transient Protection: Transient voltage suppression on power and data lines.
Driver: Not required. Uses Windows (HID) drivers.
Analog Output
Configuration: 8 output channels, each with a 16-bit D/A converter.
Input Type: ±10V or ±5V DC, configurable by channel.
Accuracy: Better than ±0.1% of span.
Discrete Input
Input Type: 4 active-high, buffered inputs, with a common connection. Inputs are tied in tandem to output drains for optional loopback monitoring of output state.
Input Signal Voltage Range: 0 to 32V DC.
Input Current: 280ÎĽA, typical at 32V DC.
Input Signal Threshold: 1.7V DC typical with 100mV of hysteresis.
Input Resistance: 10K ohms, typical.
Input Response Time: 10ms, nominal.
Discrete Output
Output Type: 4 open-source, smart, p-channel mosfet switches with a common drain connection. Provides high-side (sourcing) switching between the load and return.
Output Signal Voltage Range: 0 to 32V DC. 6-32V excitation source required.
Output “ON” Resistance: 0.5 ohms typical, 1.0 ohms maximum.
Output “ON” Current Range: 0 to 250mA DC, continuous (up to 1A total for all 4 channels combined).
Output Response Time: 10ms, nominal.
Ethernet Communication
Protocols
Modbus TCP/IP, i2o® peer-to-peer available for Modbus TCP/IP only.
Ethernet/IP or Profinet, depending on model number.
Ethernet Communication Controller: Innovasic RapID™ Platform with PriorityChannel™ for determinism at the device regardless of network load.
Modbus TCP/IP (slave): Port 502 reserved. Supports up to 10 sockets.
i2o Peer-to-Peer (master/slave): Can map 4-channel input groups to output groups at two destination IP addresses. Timed or change-of-state updates. Supports GPRS/GSM systems.
Ethernet/IP (adapter): Supports 16 connections. EDS file on website.
Profinet (server): Supports 1 connection. GSDML file on website.
Connectors: Two shielded 8-pin RJ-45 sockets, 10BaseT/100BaseTX.
Wiring: Auto-crossover for MDI or MDI-X.
IP Address: User-configurable. 192.168.1.100 default static IP address.
Data Rate: Auto-negotiated, 10Mbps or 100Mbps.
Compliance: IEEE 802.3, 802.3u, 802.3x.
Environmental
Operating Temperature: -40 to 65°C (-40 to 149°F).
Storage: -40 to 85°C (-40 to 185°F).
Relative Humidity: 5 to 95% non-condensing.
Power Requirement: 12 to 32V DC (110mA maximum @ 24V).
Isolation
I/O channels (as a group), network (each port), and power circuits isolated from each other.
Peak: 1500V AC, ANSI/ISA-82.01-1988.
Continuous: 250V AC, 354V DC.
Electromagnetic Compatibility (EMC) Compliance
Radiated Emissions: BS EN 61000-6-4, CISPR 16.
RFI: BS EN 61000-6-2, IEC 61000-4-3.
Conducted RFI: BS EN 61000-6-2, IEC 61000-4-6.
ESD: BS EN 61000-6-2, IEC 61000-4-2.
EFT: BS EN 61000-6-2, IEC 61000-4-4.
Surge Immunity: BS EN 61000-6-2, IEC 61000-4-5.
MTBF
457,517 hrs. at 25°C.
339,622 hrs. at 40°C.
Shock and Vibration Immunity
Vibration: 4g, per IEC 60068-2-64.
Shock: 25g, per IEC 60068-2-27.
Approvals: CE compliant. UL/cUL listings. Designed for Class I; Division 2; Groups ABCD; Zone 2. ATEX Certified.
Physical
General: General purpose plastic enclosure for mounting on 35mm “T-type” DIN rail.
Case Material: Self-extinguishing polyamide, UL94 V-0 rated, color light gray. General purpose NEMA Type 1 enclosure.
Circuit Board: Military grade fire-retardant epoxy glass (IPC-4101/98).
I/O Connectors: Removable plug-in type terminal blocks rated for 12A/250V; AWG #26-12, stranded/solid copper wire.
Dimensions
Width = 22.5mm (0.9 inches).
Length = 114.5mm (4.51 inches).
Depth = 99.0mm (3.90 inches).
Shipping Weight: 0.5 pounds (0.22 Kg) packed.
Learn more about the Ethernet XT Series and view all models >
- i2o® peer-to-peer available for Modbus TCP/IP only
- i2o® peer-to-peer updates based on change-of-state and/or timed updates
- Multi-function, multi-channel stand alone module is very economical
- Built-in 10K ohm pull-down resistors for 2/3-wire sensors (contacts, promixity, TTL)
- Configurable normal/reverse input logic
- Outputs include built-in read-back capability
- Easy setup with Windows software via USB
- Continuously changing “heart-beat” register validates module operation
- High-Density 22.5mm wide package with pluggable, front-facing terminals
- Dual Ethernet 10/100 ports (auto-negotiation) reduce switch port requirements
- 1500V AC isolation (between I/O, power, and network ports) and surge/transient protection
- Supports bussed/rail and redundant power
- -40°C to 70°C wide temperature operation
- Withstands 25g shock and 4g vibration
- CE and UL/cUL Class 1 Div 2 Zone 2 approvals
- ATEX Certified.
- 8 Analog DC Voltage Outputs ±10V (calibrated), ±5V (sub-range)
- 4 Discrete Voltage I/O Channels 0-32V DC
- 12 to 32V DC Power (2.8W)
- Modbus TCP/IP, Ethernet/IP, Profinet
- i2o® peer-to-peer available for Modbus TCP/IP only
Specifications
Manuals
Brochure
-
5035 Series: Ethernet Cables
- Ethernet straight cable, CAT5
- Ethernet crossover cable, CAT5E
- Low EMI Double-Shielded Ethernet Patch Cable
-
XT-SIP: Software Interface Package
- Software Interface Package for BusWorks XT Series Ethernet I/O modules.
- Easy setup and digital calibration via USB with Windows configuration software
- Download software only from the Software Tab below
Additional information
Weight | 8 oz |
---|---|
Dimensions | 4.5 × 1.5 × 5 in |
Product Name | XT1541-000: Modbus TCP/IP and i2o protocol, XT1542-000: Ethernet/IP protocol, XT1543-000: PROFINET protocol |
Part Number | XT1541-000: Modbus TCP/IP and i2o protocol, XT1542-000: Ethernet/IP protocol, XT1543-000: PROFINET protocol |
Communication | Ethernet/IP, i2o Peer-to-Peer, Modbus TCP/IP, Profinet |
Configuration | USB Configuration, Windows Software Configuration |
Product Series | BusWorks XT Series |
-
Description
XT1540: Analog Output & Digital I/O Ethernet Modules Description
The XT1540 interfaces analog output and discrete I/O signals between measurement and control devices over Ethernet.
Discrete I/O are individually configurable for input or high-side switched output operation.
Rugged construction, high density design, and easy USB-to-PC/Windows setup combine for a very effective I/O solution.
These units are ideal for remote monitoring, distributed control, or SCADA applications.
Analog Output Ranges: ±5V, ±10V DC.
Discrete Input/Output Ranges
Input: 0-32V DC, TTL thresholds.
Output: 0-32V DC, open-source, up to 250mA.
Ethernet Communication
Modbus TCP/IP, i2o® peer-to-peer available for Modbus TCP/IP only.
Ethernet/IP
Profinet
10/100Base-T(X)
PriorityChannel™ device determinismPower Requirement: 12 to 32V DC (2.8W).
Learn more about the Ethernet XT Series and view all models >
XT1540: Analog Output & Digital I/O Ethernet Modules Performance Specifications
IMPORTANT: To prevent damage or errors from grounded PCs and surges, Acromag strongly recommends use of the USB-ISOLATOR when configuring an XT1000 I/O module.
USB Interface
USB Connector
Type: USB Mini-B type socket, 5-pin.Data Rate: 12Mbps. USB v1.1 and 2.0 compatible.
Cable Length: 5.0 meters maximum.
USB Transient Protection: Transient voltage suppression on power and data lines.
Driver: Not required. Uses Windows (HID) drivers.
Analog Output
Configuration: 8 output channels, each with a 16-bit D/A converter.
Input Type: ±10V or ±5V DC, configurable by channel.
Accuracy: Better than ±0.1% of span.
Discrete Input
Input Type: 4 active-high, buffered inputs, with a common connection. Inputs are tied in tandem to output drains for optional loopback monitoring of output state.
Input Signal Voltage Range: 0 to 32V DC.
Input Current: 280ÎĽA, typical at 32V DC.
Input Signal Threshold: 1.7V DC typical with 100mV of hysteresis.
Input Resistance: 10K ohms, typical.
Input Response Time: 10ms, nominal.
Discrete Output
Output Type: 4 open-source, smart, p-channel mosfet switches with a common drain connection. Provides high-side (sourcing) switching between the load and return.
Output Signal Voltage Range: 0 to 32V DC. 6-32V excitation source required.
Output “ON” Resistance: 0.5 ohms typical, 1.0 ohms maximum.
Output “ON” Current Range: 0 to 250mA DC, continuous (up to 1A total for all 4 channels combined).
Output Response Time: 10ms, nominal.
Ethernet Communication
Protocols
Modbus TCP/IP, i2o® peer-to-peer available for Modbus TCP/IP only.
Ethernet/IP or Profinet, depending on model number.Ethernet Communication Controller: Innovasic RapID™ Platform with PriorityChannel™ for determinism at the device regardless of network load.
Modbus TCP/IP (slave): Port 502 reserved. Supports up to 10 sockets.
i2o Peer-to-Peer (master/slave): Can map 4-channel input groups to output groups at two destination IP addresses. Timed or change-of-state updates. Supports GPRS/GSM systems.
Ethernet/IP (adapter): Supports 16 connections. EDS file on website.
Profinet (server): Supports 1 connection. GSDML file on website.
Connectors: Two shielded 8-pin RJ-45 sockets, 10BaseT/100BaseTX.
Wiring: Auto-crossover for MDI or MDI-X.
IP Address: User-configurable. 192.168.1.100 default static IP address.
Data Rate: Auto-negotiated, 10Mbps or 100Mbps.
Compliance: IEEE 802.3, 802.3u, 802.3x.
Environmental
Operating Temperature: -40 to 65°C (-40 to 149°F).
Storage: -40 to 85°C (-40 to 185°F).
Relative Humidity: 5 to 95% non-condensing.
Power Requirement: 12 to 32V DC (110mA maximum @ 24V).
Isolation
I/O channels (as a group), network (each port), and power circuits isolated from each other.
Peak: 1500V AC, ANSI/ISA-82.01-1988.
Continuous: 250V AC, 354V DC.Electromagnetic Compatibility (EMC) Compliance
Radiated Emissions: BS EN 61000-6-4, CISPR 16.
RFI: BS EN 61000-6-2, IEC 61000-4-3.
Conducted RFI: BS EN 61000-6-2, IEC 61000-4-6.
ESD: BS EN 61000-6-2, IEC 61000-4-2.
EFT: BS EN 61000-6-2, IEC 61000-4-4.
Surge Immunity: BS EN 61000-6-2, IEC 61000-4-5.MTBF
457,517 hrs. at 25°C.
339,622 hrs. at 40°C.Shock and Vibration Immunity
Vibration: 4g, per IEC 60068-2-64.
Shock: 25g, per IEC 60068-2-27.Approvals: CE compliant. UL/cUL listings. Designed for Class I; Division 2; Groups ABCD; Zone 2. ATEX Certified.
Physical
General: General purpose plastic enclosure for mounting on 35mm “T-type” DIN rail.
Case Material: Self-extinguishing polyamide, UL94 V-0 rated, color light gray. General purpose NEMA Type 1 enclosure.
Circuit Board: Military grade fire-retardant epoxy glass (IPC-4101/98).
I/O Connectors: Removable plug-in type terminal blocks rated for 12A/250V; AWG #26-12, stranded/solid copper wire.
Dimensions
Width = 22.5mm (0.9 inches).
Length = 114.5mm (4.51 inches).
Depth = 99.0mm (3.90 inches).Shipping Weight: 0.5 pounds (0.22 Kg) packed.
Learn more about the Ethernet XT Series and view all models >
-
Features & Benefits
- i2o® peer-to-peer available for Modbus TCP/IP only
- i2o® peer-to-peer updates based on change-of-state and/or timed updates
- Multi-function, multi-channel stand alone module is very economical
- Built-in 10K ohm pull-down resistors for 2/3-wire sensors (contacts, promixity, TTL)
- Configurable normal/reverse input logic
- Outputs include built-in read-back capability
- Easy setup with Windows software via USB
- Continuously changing “heart-beat” register validates module operation
- High-Density 22.5mm wide package with pluggable, front-facing terminals
- Dual Ethernet 10/100 ports (auto-negotiation) reduce switch port requirements
- 1500V AC isolation (between I/O, power, and network ports) and surge/transient protection
- Supports bussed/rail and redundant power
- -40°C to 70°C wide temperature operation
- Withstands 25g shock and 4g vibration
- CE and UL/cUL Class 1 Div 2 Zone 2 approvals
- ATEX Certified.
-
Tech Papers
How to Communicate with Acromag Ethernet/IP Modules from CompactLogix Controllers - 8500762Communicating with Acromag Series 9xxEN-60xx, XTxxx2-xxx, and NTE2xxx-xxxx Ethernet/IP™ Modules from CompactLogix™ PLC Device This document illustrates a procedure for configuring message commands intended for Acromag Busworks® Series Ethernet/IP modules using Ladder Logic programming software in addition to a CompactLogix Programmable Controller. It is assumed that the user has a working knowledge of; Ladder Logic...- 8 Analog DC Voltage Outputs ±10V (calibrated), ±5V (sub-range)
- 4 Discrete Voltage I/O Channels 0-32V DC
- 12 to 32V DC Power (2.8W)
- Modbus TCP/IP, Ethernet/IP, Profinet
- i2o® peer-to-peer available for Modbus TCP/IP only
How to Communicate with Modbus/TCP Modules from Ignition Software - 8501121Setting Up and Communicating with Acromag Series 9xxEN-40xx and XTxxx1-xxx Modbus/TCP Modules and EtherStax™ Modbus/TCP from Ignition Software This document illustrates a procedure for configuring OPC tags intended for Acromag BusWorks® Series Modbus/TCP modules using Windows software from Inductive Automation. It is assumed that the user has a working knowledge of OPC, Modbus TCP, and...How to Connect to Acromag Ethernet I/O Devices - 8500815Getting Connected to Acromag Ethernet I/O Devices These instructions summarize the basic steps you will have to take in order to initially connect an Acromag Ethernet I/O product to your Personal Computer (PC) or laptop. To connect an Ethernet device to your PC, consult with your network administrator. Either temporarily change the TCP/IP configuration of...How to Communicate with Ethernet XT Profinet from Siemens S7-1200 PLC - 8501007Communicating with Acromag Model XTxxx3-000 Profinet I/O Modules from a Siemens S7-1200 PLC EthernetXT Profinet and Siemens S7-1200 When setting up a Profinet network, Profinet controllers are programmed with a special Profinet Configuration tool, like the Step7 from Siemens. This document illustrates an example procedure for configuring communications between Acromag BusWorks® Series Profinet modules and... -
Specs & Data Sheets
Specifications
Manuals
Brochure
-
Software
XT-SIP: Software Interface Information Page (Log in to download the file)Ethernet XT Series Configuration Software (Log in to download the file)ESW-MBLIB: Ethernet Modbus C Library Software Information Page (Log in to download the file)AMTx: Modbus TCP/IP Software Information Page (Log in to download the file)Profinet GSDML Files for XTxxx3-000 Modules (Log in to download the file)Ethernet IP EDS For XTxxx2-000 Modules (Log in to download the file) -
Accessories
-
5035 Series: Ethernet Cables
- Ethernet straight cable, CAT5
- Ethernet crossover cable, CAT5E
- Low EMI Double-Shielded Ethernet Patch Cable
-
XT-SIP: Software Interface Package
- Software Interface Package for BusWorks XT Series Ethernet I/O modules.
- Easy setup and digital calibration via USB with Windows configuration software
- Download software only from the Software Tab below
-
-
Additional information
Additional information
Weight 8 oz Dimensions 4.5 × 1.5 × 5 in Product Name XT1541-000: Modbus TCP/IP and i2o protocol, XT1542-000: Ethernet/IP protocol, XT1543-000: PROFINET protocol
Part Number XT1541-000: Modbus TCP/IP and i2o protocol, XT1542-000: Ethernet/IP protocol, XT1543-000: PROFINET protocol
Communication Ethernet/IP, i2o Peer-to-Peer, Modbus TCP/IP, Profinet
Configuration USB Configuration, Windows Software Configuration
Product Series BusWorks XT Series
Please login to submit this form.