Click to zoom

Please sign in or register to see model options and to add products to your cart.

Product short description:
  • Input: ±5V, ±10V, 0-5V, 0-10V
  • 16 analog single-ended voltage input channels
  • 12 to 32V DC Power (2.8W)
  • Modbus TCP/IP, Ethernet/IP, Profinet
  • i2o® peer-to-peer available for Modbus TCP/IP only

The XT1240 offers an isolated Ethernet network interface for up to to sixteen single-ended voltage input channels.

XT1240: 16-Channel Single-ended Analog DC Voltage Input Module Description

The XT1240 offers an isolated Ethernet network interface for up to to sixteen single-ended voltage input channels. Single-ended inputs enable a higher channel density to save space and a lower cost per channel.

Rugged construction, high density design, and easy USB-to-PC/Windows setup combine for a very effective and reliable module. These units are ideal for remote monitoring, distributed control, or SCADA applications.

Input Ranges
DC Voltage: ±5V, ±10V, 0 to 5V, 0 to 10V.

Ethernet Communication
Modbus TCP/IP, i2o® peer-to-peer available for Modbus TCP/IP only.
Ethernet/IP
Profinet
10/100Base-T(X)
PriorityChannel™ device determinism

Power Requirement: 12 to 32V DC (2.8W).

Performance Specifications

IMPORTANT: To prevent damage or errors from grounded PCs and surges, Acromag strongly recommends use of the USB-ISOLATOR when configuring an XT1000 I/O module.

USB Interface

USB Connector

Type: USB Mini-B type socket, 5-pin.

Data Rate: 12Mbps. USB v1.1 and 2.0 compatible.

Cable Length: 5.0 meters maximum.

USB Transient Protection: Transient voltage suppression on power and data lines.

Driver: Not required. Uses Windows (HID) drivers.

Input

Accuracy: ±0.05% of span, typical for nominal input ranges.

Analog to Digital Converter (A/D): 16-bit Σ-Δ converter. 351.6uV/bit resolution.

Noise Rejection: Better than -110dB @ 60Hz.

Input Filter Bandwidth: -3dB at 25KHz, typical.

Input Conversion Rate: 10ms for all 16 input channels.

Input Impedance: 105.2k ohms.

Ethernet Communication

Protocols
Modbus TCP/IP, i2o® peer-to-peer available for Modbus TCP/IP only.
Ethernet/IP or Profinet, depending on model number.

Ethernet Communication Controller: Innovasic RapID™ Platform with PriorityChannel™ for determinism at the device regardless of network load.

Modbus TCP/IP (slave): Port 502 reserved. Supports up to 10 sockets.

i2o Peer-to-Peer (master/slave): Can map each of 16 analog input channels separately to output channels. Timed (1-65535 sec) or percent of change updates. Supports GPRS/GSM systems.

Ethernet/IP (adapter): Supports 10 connections. EDS file on website.

Profinet (server): Supports 1 connection. GSDML file on website.

Connectors: Two shielded 8-pin RJ-45 sockets, 10BaseT/100BaseTX.

Wiring: Auto-crossover for MDI or MDI-X.

IP Address: User-configurable. 192.168.1.100 default IP address.

Data Rate: Auto-negotiated, 10Mbps or 100Mbps.

Compliance: IEEE 802.3, 802.3u, 802.3x.

Environmental

Operating temperature: -40 to 70°C (-40 to 158°F).

Storage temperature: -40 to 85°C (-40 to 185°F).

Relative humidity: 5 to 95% non-condensing.

MTBF:
458,991 hrs. at 25°C.
338,846 hrs. at 40°C.

Power Requirement: 12 to 32V DC, 2.8W maximum (113mA maximum @ 24V).

Isolation
4-way isolation between I/O channels, network (each port), and power.
Peak: 1500V AC, ANSI/ISA-82.01-1988.
Continuous: 250V AC, 354V DC.

Shock and Vibration Immunity
Vibration: 4g, per IEC 60068-2-64.
Shock: 25g, per IEC 60068-2-27.

Electromagnetic Compatibility (EMC) Compliance
Radiated Emissions: BS EN 61000-6-4, CISPR 16.
RFI: BS EN 61000-6-2, IEC 61000-4-3.
Conducted RFI: BS EN 61000-6-2, IEC 61000-4-6.
ESD: BS EN 61000-6-2, IEC 61000-4-2.
EFT: BS EN 61000-6-2, IEC 61000-4-4.
Surge Immunity: BS EN 61000-6-2, IEC 61000-4-5.

Approvals: CE compliant. UL/cUL Class I; Div. 2 Zone 2. ATEX Certified.

Physical

General: General purpose plastic enclosure for mounting on 35mm “T-type” DIN rail.

Case Material: Self-extinguishing polyamide, UL94 V-0 rated, color light gray. General purpose NEMA Type 1 enclosure.

Circuit Board: Military grade fire-retardant epoxy glass (IPC-4101/98).

I/O Connectors: Removable plug-in type terminal blocks rated for 12A/250V; AWG #26-12, stranded/solid copper wire.

Dimensions
Width = 22.5mm (0.9 inches).
Length = 114.5mm (4.51 inches).
Depth = 99.0mm (3.90 inches).

Shipping Weight: 0.5 pounds (0.22 Kg) packed.

  • i2o® peer-to-peer available for Modbus TCP/IP only
  • i2o® peer-to-peer updates based on change-of-state and/or timed updates
  • Easy setup with Windows software via USB
  • High input impendance (100K ohms) reduces loading on voltage loops
  • User-configurable sample averaging (1-200) on a per-channel basis
  • 10ms network updates for all 16 input channels
  • High-resolution 16-bit Σ∆ A/D converter ensures precise, high accuracy measurements
  • High-Density 22.5mm wide package with pluggable, front-facing terminals
  • Dual Ethernet 10/100 ports (auto-negotiation) reduce switch port requirements
  • 1500V AC isolation (between I/O, power, and network ports) and surge/transient protection
  • Supports bussed/rail and redundant power
  • -40°C to 70°C wide temperature operation
  • Withstands 25g shock and 4g vibration
  • CE compliant. UL/cUL Class 1 Div 2 Zone 2 approvals.
  • ATEX Certified.
How to Communicate with Acromag Ethernet/IP Modules from CompactLogix Controllers - 8500762
Communicating with Acromag Series 9xxEN-60xx and XTxxx2-xxx Ethernet/IP™ Modules from CompactLogix™ Controllers This document illustrates a procedure for configuring message commands intended for Acromag Busworks® Series Ethernet/IP modules using Ladder Logic programming software in addition to a CompactLogix Programmable Controller. It is assumed that the user has a working knowledge of; Ladder Logic programming and...
How to Connect to Acromag Ethernet I/O Devices - 8500815
Getting Connected to Acromag Ethernet I/O Devices These instructions summarize the basic steps you will have to take in order to initially connect an Acromag Ethernet I/O product to your Personal Computer (PC) or laptop. To connect an Ethernet device to your PC, consult with your network administrator. Either temporarily change the TCP/IP configuration of...
How to Communicate with Ethernet XT Profinet from Siemens S7-1200 PLC - 8501007
Communicating with Acromag Model XTxxx3-000 Profinet I/O Modules from a Siemens S7-1200 PLC EthernetXT Profinet and Siemens S7-1200 When setting up a Profinet network, Profinet controllers are programmed with a special Profinet Configuration tool, like the Step7 from Siemens. This document illustrates an example procedure for configuring communications between Acromag BusWorks® Series Profinet modules and...
How to Communicate to Ethernet Modules from Red Lion HMIs - 8500874
How to Communicate to Acromag Ethernet Modules from Red Lion HMIs Red Lion HMIs This document illustrates a procedure for configuring message commands for Acromag Ethernet modules using the Red Lion Crimson 2.0 software. It is assumed that the user has a working knowledge of the Crimson 2.0 software, as well as a Red Lion...

Manuals

XT1231 / XT1241 User Manual (Log in to download the file)

XT1232 / XT1242 User Manual (Log in to download the file)

XT1233 / XT1243 User Manual (Log in to download the file)

XT-SIP: Software Interface Information Page (Log in to download the file)
ESW-MBLIB: Ethernet Modbus C Library Software Information Page (Log in to download the file)
Ethernet XT Series Configuration Software (Log in to download the file)
AMTx: Modbus TCP/IP Software Information Page (Log in to download the file)
Profinet GSDML Files for XTxxx3-000 Modules (Log in to download the file)
Ethernet IP EDS For XTxxx2-000 Modules (Log in to download the file)
  • Compare

    XT-SIP: Software Interface Package

    • Software Interface Package for BusWorks XT Series Ethernet I/O modules.
    • Easy setup and digital calibration via USB with Windows configuration software
    • Download software only from the Software Tab below
    Select options

Additional information

Weight 8 oz
Dimensions 4.5 × 1.5 × 5 in
Part Number

XT1241-000: Modbus TCP/IP and i2o protocol, XT1242-000: Ethernet/IP protocol, XT1243-000: Profinet protocol

Communication

Ethernet/IP, i2o Peer-to-Peer, Modbus TCP/IP, Profinet

Configuration

USB Configuration, Windows Software Configuration

Product Series

BusWorks XT Series

  • Description

    XT1240: 16-Channel Single-ended Analog DC Voltage Input Module Description

    The XT1240 offers an isolated Ethernet network interface for up to to sixteen single-ended voltage input channels. Single-ended inputs enable a higher channel density to save space and a lower cost per channel.

    Rugged construction, high density design, and easy USB-to-PC/Windows setup combine for a very effective and reliable module. These units are ideal for remote monitoring, distributed control, or SCADA applications.

    Input Ranges
    DC Voltage: ±5V, ±10V, 0 to 5V, 0 to 10V.

    Ethernet Communication
    Modbus TCP/IP, i2o® peer-to-peer available for Modbus TCP/IP only.
    Ethernet/IP
    Profinet
    10/100Base-T(X)
    PriorityChannel™ device determinism

    Power Requirement: 12 to 32V DC (2.8W).

    Performance Specifications

    IMPORTANT: To prevent damage or errors from grounded PCs and surges, Acromag strongly recommends use of the USB-ISOLATOR when configuring an XT1000 I/O module.

    USB Interface

    USB Connector

    Type: USB Mini-B type socket, 5-pin.

    Data Rate: 12Mbps. USB v1.1 and 2.0 compatible.

    Cable Length: 5.0 meters maximum.

    USB Transient Protection: Transient voltage suppression on power and data lines.

    Driver: Not required. Uses Windows (HID) drivers.

    Input

    Accuracy: ±0.05% of span, typical for nominal input ranges.

    Analog to Digital Converter (A/D): 16-bit Σ-Δ converter. 351.6uV/bit resolution.

    Noise Rejection: Better than -110dB @ 60Hz.

    Input Filter Bandwidth: -3dB at 25KHz, typical.

    Input Conversion Rate: 10ms for all 16 input channels.

    Input Impedance: 105.2k ohms.

    Ethernet Communication

    Protocols
    Modbus TCP/IP, i2o® peer-to-peer available for Modbus TCP/IP only.
    Ethernet/IP or Profinet, depending on model number.

    Ethernet Communication Controller: Innovasic RapID™ Platform with PriorityChannel™ for determinism at the device regardless of network load.

    Modbus TCP/IP (slave): Port 502 reserved. Supports up to 10 sockets.

    i2o Peer-to-Peer (master/slave): Can map each of 16 analog input channels separately to output channels. Timed (1-65535 sec) or percent of change updates. Supports GPRS/GSM systems.

    Ethernet/IP (adapter): Supports 10 connections. EDS file on website.

    Profinet (server): Supports 1 connection. GSDML file on website.

    Connectors: Two shielded 8-pin RJ-45 sockets, 10BaseT/100BaseTX.

    Wiring: Auto-crossover for MDI or MDI-X.

    IP Address: User-configurable. 192.168.1.100 default IP address.

    Data Rate: Auto-negotiated, 10Mbps or 100Mbps.

    Compliance: IEEE 802.3, 802.3u, 802.3x.

    Environmental

    Operating temperature: -40 to 70°C (-40 to 158°F).

    Storage temperature: -40 to 85°C (-40 to 185°F).

    Relative humidity: 5 to 95% non-condensing.

    MTBF:
    458,991 hrs. at 25°C.
    338,846 hrs. at 40°C.

    Power Requirement: 12 to 32V DC, 2.8W maximum (113mA maximum @ 24V).

    Isolation
    4-way isolation between I/O channels, network (each port), and power.
    Peak: 1500V AC, ANSI/ISA-82.01-1988.
    Continuous: 250V AC, 354V DC.

    Shock and Vibration Immunity
    Vibration: 4g, per IEC 60068-2-64.
    Shock: 25g, per IEC 60068-2-27.

    Electromagnetic Compatibility (EMC) Compliance
    Radiated Emissions: BS EN 61000-6-4, CISPR 16.
    RFI: BS EN 61000-6-2, IEC 61000-4-3.
    Conducted RFI: BS EN 61000-6-2, IEC 61000-4-6.
    ESD: BS EN 61000-6-2, IEC 61000-4-2.
    EFT: BS EN 61000-6-2, IEC 61000-4-4.
    Surge Immunity: BS EN 61000-6-2, IEC 61000-4-5.

    Approvals: CE compliant. UL/cUL Class I; Div. 2 Zone 2. ATEX Certified.

    Physical

    General: General purpose plastic enclosure for mounting on 35mm “T-type” DIN rail.

    Case Material: Self-extinguishing polyamide, UL94 V-0 rated, color light gray. General purpose NEMA Type 1 enclosure.

    Circuit Board: Military grade fire-retardant epoxy glass (IPC-4101/98).

    I/O Connectors: Removable plug-in type terminal blocks rated for 12A/250V; AWG #26-12, stranded/solid copper wire.

    Dimensions
    Width = 22.5mm (0.9 inches).
    Length = 114.5mm (4.51 inches).
    Depth = 99.0mm (3.90 inches).

    Shipping Weight: 0.5 pounds (0.22 Kg) packed.

  • Features & Benefits

    • i2o® peer-to-peer available for Modbus TCP/IP only
    • i2o® peer-to-peer updates based on change-of-state and/or timed updates
    • Easy setup with Windows software via USB
    • High input impendance (100K ohms) reduces loading on voltage loops
    • User-configurable sample averaging (1-200) on a per-channel basis
    • 10ms network updates for all 16 input channels
    • High-resolution 16-bit Σ∆ A/D converter ensures precise, high accuracy measurements
    • High-Density 22.5mm wide package with pluggable, front-facing terminals
    • Dual Ethernet 10/100 ports (auto-negotiation) reduce switch port requirements
    • 1500V AC isolation (between I/O, power, and network ports) and surge/transient protection
    • Supports bussed/rail and redundant power
    • -40°C to 70°C wide temperature operation
    • Withstands 25g shock and 4g vibration
    • CE compliant. UL/cUL Class 1 Div 2 Zone 2 approvals.
    • ATEX Certified.
  • Tech Papers

    How to Communicate with Acromag Ethernet/IP Modules from CompactLogix Controllers - 8500762
    Communicating with Acromag Series 9xxEN-60xx and XTxxx2-xxx Ethernet/IP™ Modules from CompactLogix™ Controllers This document illustrates a procedure for configuring message commands intended for Acromag Busworks® Series Ethernet/IP modules using Ladder Logic programming software in addition to a CompactLogix Programmable Controller. It is assumed that the user has a working knowledge of; Ladder Logic programming and...
    How to Connect to Acromag Ethernet I/O Devices - 8500815
    Getting Connected to Acromag Ethernet I/O Devices These instructions summarize the basic steps you will have to take in order to initially connect an Acromag Ethernet I/O product to your Personal Computer (PC) or laptop. To connect an Ethernet device to your PC, consult with your network administrator. Either temporarily change the TCP/IP configuration of...
    How to Communicate with Ethernet XT Profinet from Siemens S7-1200 PLC - 8501007
    Communicating with Acromag Model XTxxx3-000 Profinet I/O Modules from a Siemens S7-1200 PLC EthernetXT Profinet and Siemens S7-1200 When setting up a Profinet network, Profinet controllers are programmed with a special Profinet Configuration tool, like the Step7 from Siemens. This document illustrates an example procedure for configuring communications between Acromag BusWorks® Series Profinet modules and...
    How to Communicate to Ethernet Modules from Red Lion HMIs - 8500874
    How to Communicate to Acromag Ethernet Modules from Red Lion HMIs Red Lion HMIs This document illustrates a procedure for configuring message commands for Acromag Ethernet modules using the Red Lion Crimson 2.0 software. It is assumed that the user has a working knowledge of the Crimson 2.0 software, as well as a Red Lion...
  • Specs & Data Sheets

    Manuals

    XT1231 / XT1241 User Manual (Log in to download the file)

    XT1232 / XT1242 User Manual (Log in to download the file)

    XT1233 / XT1243 User Manual (Log in to download the file)

  • Software

    XT-SIP: Software Interface Information Page (Log in to download the file)
    ESW-MBLIB: Ethernet Modbus C Library Software Information Page (Log in to download the file)
    Ethernet XT Series Configuration Software (Log in to download the file)
    AMTx: Modbus TCP/IP Software Information Page (Log in to download the file)
    Profinet GSDML Files for XTxxx3-000 Modules (Log in to download the file)
    Ethernet IP EDS For XTxxx2-000 Modules (Log in to download the file)
  • Accessories

    • Compare

      XT-SIP: Software Interface Package

      • Software Interface Package for BusWorks XT Series Ethernet I/O modules.
      • Easy setup and digital calibration via USB with Windows configuration software
      • Download software only from the Software Tab below
      Select options
  • Additional information

    Additional information

    Weight 8 oz
    Dimensions 4.5 × 1.5 × 5 in
    Part Number

    XT1241-000: Modbus TCP/IP and i2o protocol, XT1242-000: Ethernet/IP protocol, XT1243-000: Profinet protocol

    Communication

    Ethernet/IP, i2o Peer-to-Peer, Modbus TCP/IP, Profinet

    Configuration

    USB Configuration, Windows Software Configuration

    Product Series

    BusWorks XT Series