Click to zoom
$615$730

Please sign in or register to see model options and to add products to your cart.

Product short description:
  • 4 or 6-channel DC current or voltage output
  • Ethernet/IP, Modbus TCP/IP
  • i2o peer-to-peer available for Modbus TCP/IP only

These modules provide up to six channels of analog output. Multi-range outputs support a wide variety of industrial devices. They can drive displays and recorders, control drives, or send analog signals to other systems. High-resolution, low noise, D/A converters deliver high accuracy and reliability. Three-way isolation further improves system performance.

[DISPLAY_ULTIMATE_PLUS]

Models

972EN: DC current output channels
973EN: DC voltage output channels

These modules provide up to six channels of analog output. Multi-range outputs support a wide variety of industrial devices. They can drive displays and recorders, control drives, or send analog signals to other systems. High-resolution, low noise, D/A converters deliver high accuracy and reliability. Three-way isolation further improves system performance.

Output Ranges: Ranges selectable on channel to channel basis
972EN: DC Current (user-selectable ranges): 0 to 1mA, 0 to 20mA, or 4 to 20mA
973EN: DC Voltage (user-selectable ranges): 0 to 1V, 0 to 5V, or 0 to 10V DC
Network Communication: 
EtherNet/IP
Modbus TCP/IP, i2o® peer-to-peer available for Modbus TCP/IP only
10/100Mbps with automatic data rate negotiation
Power Requirement: 15 to 36V DC supply required. 4.6 Watts (972EN) or 2.3 Watts (973EN)
Approvals:
CE/ATEX marked
UL, cUL listed, Class I; Div. 2; Groups A, B, C, D
EtherNet/IP, Modbus/TCP conformance tested

Performance Specifications

Output

Accuracy: Better than ±0.1% of span, typical. 1.6% for 0 to 1mA range. 0.8% for 0 to 1V range
Digital to Analog Converter (D/A): 12-bit converter
Current Output Compliance: 12V minimum, 13V typical
Current Output Load Resistance Range: 0 to 555 ohms, typical
Voltage Output Source Current: 0 to 10mA DC, maximum

Environmental

Ambient Operating Temperature:
972EN models -25 to 60°C (-13 to 140°F)
973EN models: -25 to 70°C (-13 to 158°F)
Ambient Storage Temperature: -40 to 85°C (-40 to 185°F)
Relative humidity: 5 to 95%, non-condensing
Isolation:
1500V AC for 60 seconds or 250V AC continuous
3-way isolation between I/O, network, and power. Outputs share a common.

NOTE: i2o function only on Modbus TCP/IP modules

  • Configurable from standard web browser
  • 6-output stand-alone module has much lower start-up cost than multi-piece block I/O systems
  • Universal DC outputs support a wide variety of signals and industrial devices
  • Three selectable failsafe modes (0%, last-state, or pre-defined) help prevent unsafe conditions
  • Wide operational temperature range permits installation in extreme environments:
  • 972EN: -25°C to 60°C (-13°F to 140°F)
  • 973EN: -25°C to 70°C (-13°F to 158°F)
How to Connect Acromag Series 9xxEN Modules Via RadioLinx Ethernet Modems
Objective: The purpose of this document is to provide a procedure for connecting an Acromag Series 9xxEN I/O Module to an existing network via RadioLinx Ethernet Modems. Background – IP Addresses Any TCP/IP packet contains two addresses: a unique fixed MAC address, and a unique IP address. To communicate on the Internet, computers must have...
How to Communicate with Acromag Modbus/TCP Modules from Ignition Software Application Note
Communicating with Ignition Software This document illustrates a procedure for configuring OPC tags intended for Acromag Busworks® Series Modbus/TCP modules using Windows software from Inductive Automation. It is assumed that the user has a working knowledge of OPC, Modbus TCP, and Ignition software. Product Features: BusWorks® Series 9xxEN Modules w/Modbus/TCP BusWorks® Series XT1xx1 Modules w/...
How to Connect to Acromag Ethernet I/O Devices Application Note
Getting Connected to Acromag Ethernet I/O Devices These instructions summarize the basic steps you will have to take in order to initially connect an Acromag Ethernet I/O product to your Personal Computer (PC) or laptop. To connect an Ethernet device to your PC, consult with your network administrator and either temporarily change the TCP/IP configuration...
How to Connect Acromag Series 900EN Ethernet Modules to Your PC Application Note
Objective: The purpose of this document is to provide a procedure for assigning a unique IP address to a second network interface card installed in a personal computer for the purpose of communicating with an Acromag Series 9xxEN Ethernet I/O Module. A procedure for accomplishing IP address assignment is provided using Windows 98, Windows ME, Windows...
How to Communicate with Acromag Series 9xxEN-60xx & XTxxx2-xxx Ethernet/IP Modules from Compact Logix Devices Application Note
Communicating with Acromag Series 9xxEN-60xx and XTxxx2-xxx Ethernet/IP Modules from Compact Logix Controllers This document illustrates a procedure for configuring message commands intended for Acromag Busworks® Series Ethernet/IP modules using ladder logic programming software and a Compact Logix Programmable Controller. It is assumed that the user has a working knowledge of ladder logic programming, the...
How to Communicate to Acromag Series 9xxEN-6xxx & XTxx2-xxx Ethernet Modules in an Allen Bradley ControlLogix System Application Note
Ethernet Modules in a ControlLogix System Objective: This document illustrates a procedure for integrating the Acromag Series 9xxEN-6xxx modules into the Allen Bradley control system as a third-party generic module. The reference model for this procedure is the Model 961EN-6006. It is assumed that the Acromag module has been assigned a static IP address and...
How to Configure Kepware KEPServerEX 5.0 for Communications with Acromag BusWorks Modbus I/O Modules Application Note
Configuring Kepware KEPServerEX 5.0 for Communications with Acromag BusWorks Modbus I/O modules. Introduction This document provides example steps for configuring the Kepware KEPServerEX OPC Server for communications with Acromag Busworks Modbus RTU and Modbus TCP/IP Distributed I/O Modules. Once the server is configured, data may be read from or written to the I/O module using...
How to Configure LabVIEW 2009 to Communicate with Acromag BusWorks and EtherStax Modbus I/O Modules Via an OPC Server Application Note
Introduction National Instruments LabVIEW can be used to monitor and control Acromag Busworks and Etherstax Modbus I/O Modules via an OPC server. A separate application note, Configuring Kepware KEPServerEX 5.0 for Communications with Acromag Busworks and Etherstax Modbus I/O Modules, outlines configuration of a KEPServerEX OPC server. This document focuses on setting up controls and...
How to Configure Omron CJ2H PLC's with Ethernet/IP for Use with Acromag Ethernet/IP Remote I/O Application Note
Purpose: Acromag Ethernet/IP I/O with Omron CJ2H PLC’s This document walks the user through the configuration of the Cx-One Network Configurator software that is used in conjunction with Omron CJ2H PLC’s. It is assumed that the user has a working knowledge of the PLC and Cx-One software. Configuring the CxOne “Network Configurator” Start the Cx-One...
How to Communicate to Acromag Series 9xxEN-60xx Ethernet Modules using PCCC from Compact Logix Devices Application Note
PCCC Messaging with CompactLogix This document illustrates a procedure for configuring PCCC message commands for Acromag Series 9xxEN Ethernet/IP modules using ladder logic programming and a Compact Logix Controller. It is assumed that the user has a working knowledge of ladder logic programming, the RSLogix5000 software, and the Compact Logix hardware. Configuring PCCC Messaging Using...
How to Communicate to Ethernet Modules from Legacy Allen Bradley or Rockwell Automation Devices Application Note
This document illustrates a procedure for configuring message commands for Acromag Series 9xxEN Ethernet/IP modules using ladder logic programming and an SLC5\05 Programmable Logic Controller. It is assumed that the user has a working knowledge of ladder logic programming, the RSLogix500 software, and the SLC 5\05 hardware. Setup of PCCC Communication to Series 9xxEN-60xx I/O...
How to Configure the Wonderware MBENET I/O Server to Communicate with the Acromag 9xxEN Ethernet Modules Application Note
Wonderware MBENET The purpose of this document is to provide a procedure for configuring MBENET I/O Server (ie: Modicon Ethernet I/O Server) to communicate with an Acromag Series 9xxEN Ethernet I/O Module. It is assumed that the user has a working knowledge of Wonderware and how to link the Wonderware application to the Wonderware I/O...
How to Communicate to Acromag Series Ethernet Modules from Red Lion HMIs Application Note
Red Lion HMIs This document illustrates a procedure for configuring message commands for Acromag Ethernet modules using the Red Lion Crimson 2.0 Software. It is assumed that the user has a working knowledge of the Crimson 2.0 software, as well as a Red Lion HMI. Setting up Communications From a new or existing project, double...

Manuals

972EN-4xxx, 973EN-4xxx User Manual (Log in to download the file)

972EN-6xxx, 973EN-6xxx User Manual (Log in to download the file)

ESW-MBLIB-DEMO (Log in to download the file)
AMTN-DEMO (Log in to download the file)
ATMX Demo Software (Log in to download the file)
Ethernet IP EDS for 9xxEN-6xxx Modules (Log in to download the file)
  • Compare

    20RM-16-DIN: 19” rack-mount kit with DIN rail

    • 19" rack-mount kit with DIN rail
    $190
    Select options
  • Compare

    4001 Serial Cables

    5-foot ribbon cable, DB25 male and 26-pin female IDC connectors, for 3B/5B backpanel to Ethernet I/O module connection
    $100
    Select options
  • Compare

    5020-350: Toroidal AC Current Sensor

    • AC Current Sensor to precondition an AC current input signal
    • Highly accurate toroidal instrument transformer that converts an AC current signal to a safe, low level, DC milliampere signal (0 to 11.17mA).
    $50
    Select options
  • Compare

    5035 Series: Ethernet Cables

    • Ethernet straight cable, CAT5
    • Ethernet crossover cable, CAT5E
    • Low EMI Double-Shielded Ethernet Patch Cable
    $45$115
    Select options
  • Compare

    900EN: 5-Port Ethernet Switch

    • 10/100Mbps
    • 15 to 36V DC power supply required
    • Five shielded RJ-45 sockets, 8-pin, 10Base-T / 100Base-TX
    $350
    Select options
  • Compare

    AMTN, AMTX: ActiveX / .NET Controls for Modbus I/O

    • Modbus/TCP or Modbus/RTU
    • These ActiveX / .NET software controls provide a fast, easy way to communicate with any Modbus slave devices connected to your PC.
    • Get your Visual Basic, Visual C, .NET, Excel, or other compatible applications talking Modbus protocol within minutes.
    $270$370
    Select options
  • Compare

    ESW-MBLIB: Ethernet Modbus C Library Software

    • Universal support for five operating systems
    • C source code provided
    • Demo program included
    $0$350
    Select options
  • Compare

    IMC-100A: 10/100BaseTX to 100BaseFX Industrial Media Converter

    • UTP to Fiber Media Converter
    • RJ45 Port Supports Auto MDI/MDI-X Function
     
    $250
    Select options
  • Compare

    PS5R: Slim Line Power Supplies

    • 10W, 15W, 30W, 60W, 90W, 120W, and 240W models
    • Universal Input (85-264V AC / 100-370V DC)
    • Lightweight and compact size
    $100$255
    Select options
  • Compare

    Terminal Block Replacements

    • Simplifies wiring connections on Acromag I/O Modules
    • Barrier strip or spring clamp terminal block kits
    • Provide safe and secure wiring connections
    $35$45
    Select options
  • Compare

    USB-to-Ethernet Adapter

    Simplifies configuration of Acromag Ethernet I/O Modules Prevents disruption of existing LANs This device is a USB-to-Ethernet adapter that you can use to communicate with any Acromag Ethernet I/O product for the purpose of setup and re-configuration for your application. It is recommended for initial communication with Acromag Ethernet devices so that you do not have to disrupt your existing network connection.
    $85
    Select options

Additional information

Weight 10 oz
Dimensions 4.5 × 1.5 × 5 in
Part Number

972EN-4004: Modbus TCP/IP and i2o protocol, 4 channel, 972EN-4006: Modbus TCP/IP and i2o protocol, 6 channel, 972EN-6004: Ethernet/IP, 4 channel, 972EN-6006, Ethernet/IP, 6 channel, 973EN-4004: Modbus TCP/IP and i2o protocol, 4 channel, 973EN-4006: Modbus TCP/IP and i2o protocol, 6 channel, 973EN-6004: Ethernet/IP, 4 channel, 973EN-6006: Ethernet/IP, 6 channel

Communication

Ethernet/IP, i2o Peer-to-Peer, Modbus TCP/IP

Product Series

BusWorks 900EN Series

Configuration

Built-in Web pages

  • Description

    Models

    972EN: DC current output channels
    973EN: DC voltage output channels

    These modules provide up to six channels of analog output. Multi-range outputs support a wide variety of industrial devices. They can drive displays and recorders, control drives, or send analog signals to other systems. High-resolution, low noise, D/A converters deliver high accuracy and reliability. Three-way isolation further improves system performance.

    Output Ranges: Ranges selectable on channel to channel basis
    972EN: DC Current (user-selectable ranges): 0 to 1mA, 0 to 20mA, or 4 to 20mA
    973EN: DC Voltage (user-selectable ranges): 0 to 1V, 0 to 5V, or 0 to 10V DC
    Network Communication: 
    EtherNet/IP
    Modbus TCP/IP, i2o® peer-to-peer available for Modbus TCP/IP only
    10/100Mbps with automatic data rate negotiation
    Power Requirement: 15 to 36V DC supply required. 4.6 Watts (972EN) or 2.3 Watts (973EN)
    Approvals:
    CE/ATEX marked
    UL, cUL listed, Class I; Div. 2; Groups A, B, C, D
    EtherNet/IP, Modbus/TCP conformance tested

    Performance Specifications

    Output

    Accuracy: Better than ±0.1% of span, typical. 1.6% for 0 to 1mA range. 0.8% for 0 to 1V range
    Digital to Analog Converter (D/A): 12-bit converter
    Current Output Compliance: 12V minimum, 13V typical
    Current Output Load Resistance Range: 0 to 555 ohms, typical
    Voltage Output Source Current: 0 to 10mA DC, maximum

    Environmental

    Ambient Operating Temperature:
    972EN models -25 to 60°C (-13 to 140°F)
    973EN models: -25 to 70°C (-13 to 158°F)
    Ambient Storage Temperature: -40 to 85°C (-40 to 185°F)
    Relative humidity: 5 to 95%, non-condensing
    Isolation:
    1500V AC for 60 seconds or 250V AC continuous
    3-way isolation between I/O, network, and power. Outputs share a common.

    NOTE: i2o function only on Modbus TCP/IP modules

  • Features & Benefits

    • Configurable from standard web browser
    • 6-output stand-alone module has much lower start-up cost than multi-piece block I/O systems
    • Universal DC outputs support a wide variety of signals and industrial devices
    • Three selectable failsafe modes (0%, last-state, or pre-defined) help prevent unsafe conditions
    • Wide operational temperature range permits installation in extreme environments:
    • 972EN: -25°C to 60°C (-13°F to 140°F)
    • 973EN: -25°C to 70°C (-13°F to 158°F)
  • Tech Papers

    How to Connect Acromag Series 9xxEN Modules Via RadioLinx Ethernet Modems
    Objective: The purpose of this document is to provide a procedure for connecting an Acromag Series 9xxEN I/O Module to an existing network via RadioLinx Ethernet Modems. Background – IP Addresses Any TCP/IP packet contains two addresses: a unique fixed MAC address, and a unique IP address. To communicate on the Internet, computers must have...
    How to Communicate with Acromag Modbus/TCP Modules from Ignition Software Application Note
    Communicating with Ignition Software This document illustrates a procedure for configuring OPC tags intended for Acromag Busworks® Series Modbus/TCP modules using Windows software from Inductive Automation. It is assumed that the user has a working knowledge of OPC, Modbus TCP, and Ignition software. Product Features: BusWorks® Series 9xxEN Modules w/Modbus/TCP BusWorks® Series XT1xx1 Modules w/...
    How to Connect to Acromag Ethernet I/O Devices Application Note
    Getting Connected to Acromag Ethernet I/O Devices These instructions summarize the basic steps you will have to take in order to initially connect an Acromag Ethernet I/O product to your Personal Computer (PC) or laptop. To connect an Ethernet device to your PC, consult with your network administrator and either temporarily change the TCP/IP configuration...
    How to Connect Acromag Series 900EN Ethernet Modules to Your PC Application Note
    Objective: The purpose of this document is to provide a procedure for assigning a unique IP address to a second network interface card installed in a personal computer for the purpose of communicating with an Acromag Series 9xxEN Ethernet I/O Module. A procedure for accomplishing IP address assignment is provided using Windows 98, Windows ME, Windows...
    How to Communicate with Acromag Series 9xxEN-60xx & XTxxx2-xxx Ethernet/IP Modules from Compact Logix Devices Application Note
    Communicating with Acromag Series 9xxEN-60xx and XTxxx2-xxx Ethernet/IP Modules from Compact Logix Controllers This document illustrates a procedure for configuring message commands intended for Acromag Busworks® Series Ethernet/IP modules using ladder logic programming software and a Compact Logix Programmable Controller. It is assumed that the user has a working knowledge of ladder logic programming, the...
    How to Communicate to Acromag Series 9xxEN-6xxx & XTxx2-xxx Ethernet Modules in an Allen Bradley ControlLogix System Application Note
    Ethernet Modules in a ControlLogix System Objective: This document illustrates a procedure for integrating the Acromag Series 9xxEN-6xxx modules into the Allen Bradley control system as a third-party generic module. The reference model for this procedure is the Model 961EN-6006. It is assumed that the Acromag module has been assigned a static IP address and...
    How to Configure Kepware KEPServerEX 5.0 for Communications with Acromag BusWorks Modbus I/O Modules Application Note
    Configuring Kepware KEPServerEX 5.0 for Communications with Acromag BusWorks Modbus I/O modules. Introduction This document provides example steps for configuring the Kepware KEPServerEX OPC Server for communications with Acromag Busworks Modbus RTU and Modbus TCP/IP Distributed I/O Modules. Once the server is configured, data may be read from or written to the I/O module using...
    How to Configure LabVIEW 2009 to Communicate with Acromag BusWorks and EtherStax Modbus I/O Modules Via an OPC Server Application Note
    Introduction National Instruments LabVIEW can be used to monitor and control Acromag Busworks and Etherstax Modbus I/O Modules via an OPC server. A separate application note, Configuring Kepware KEPServerEX 5.0 for Communications with Acromag Busworks and Etherstax Modbus I/O Modules, outlines configuration of a KEPServerEX OPC server. This document focuses on setting up controls and...
    How to Configure Omron CJ2H PLC's with Ethernet/IP for Use with Acromag Ethernet/IP Remote I/O Application Note
    Purpose: Acromag Ethernet/IP I/O with Omron CJ2H PLC’s This document walks the user through the configuration of the Cx-One Network Configurator software that is used in conjunction with Omron CJ2H PLC’s. It is assumed that the user has a working knowledge of the PLC and Cx-One software. Configuring the CxOne “Network Configurator” Start the Cx-One...
    How to Communicate to Acromag Series 9xxEN-60xx Ethernet Modules using PCCC from Compact Logix Devices Application Note
    PCCC Messaging with CompactLogix This document illustrates a procedure for configuring PCCC message commands for Acromag Series 9xxEN Ethernet/IP modules using ladder logic programming and a Compact Logix Controller. It is assumed that the user has a working knowledge of ladder logic programming, the RSLogix5000 software, and the Compact Logix hardware. Configuring PCCC Messaging Using...
    How to Communicate to Ethernet Modules from Legacy Allen Bradley or Rockwell Automation Devices Application Note
    This document illustrates a procedure for configuring message commands for Acromag Series 9xxEN Ethernet/IP modules using ladder logic programming and an SLC5\05 Programmable Logic Controller. It is assumed that the user has a working knowledge of ladder logic programming, the RSLogix500 software, and the SLC 5\05 hardware. Setup of PCCC Communication to Series 9xxEN-60xx I/O...
    How to Configure the Wonderware MBENET I/O Server to Communicate with the Acromag 9xxEN Ethernet Modules Application Note
    Wonderware MBENET The purpose of this document is to provide a procedure for configuring MBENET I/O Server (ie: Modicon Ethernet I/O Server) to communicate with an Acromag Series 9xxEN Ethernet I/O Module. It is assumed that the user has a working knowledge of Wonderware and how to link the Wonderware application to the Wonderware I/O...
    How to Communicate to Acromag Series Ethernet Modules from Red Lion HMIs Application Note
    Red Lion HMIs This document illustrates a procedure for configuring message commands for Acromag Ethernet modules using the Red Lion Crimson 2.0 Software. It is assumed that the user has a working knowledge of the Crimson 2.0 software, as well as a Red Lion HMI. Setting up Communications From a new or existing project, double...
  • Specs & Data Sheets

    Manuals

    972EN-4xxx, 973EN-4xxx User Manual (Log in to download the file)

    972EN-6xxx, 973EN-6xxx User Manual (Log in to download the file)

  • Software

    ESW-MBLIB-DEMO (Log in to download the file)
    AMTN-DEMO (Log in to download the file)
    ATMX Demo Software (Log in to download the file)
    Ethernet IP EDS for 9xxEN-6xxx Modules (Log in to download the file)
  • Accessories

    • Compare

      20RM-16-DIN: 19” rack-mount kit with DIN rail

      • 19" rack-mount kit with DIN rail
      $190
      Select options
    • Compare

      4001 Serial Cables

      5-foot ribbon cable, DB25 male and 26-pin female IDC connectors, for 3B/5B backpanel to Ethernet I/O module connection
      $100
      Select options
    • Compare

      5020-350: Toroidal AC Current Sensor

      • AC Current Sensor to precondition an AC current input signal
      • Highly accurate toroidal instrument transformer that converts an AC current signal to a safe, low level, DC milliampere signal (0 to 11.17mA).
      $50
      Select options
    • Compare

      5035 Series: Ethernet Cables

      • Ethernet straight cable, CAT5
      • Ethernet crossover cable, CAT5E
      • Low EMI Double-Shielded Ethernet Patch Cable
      $45$115
      Select options
    • Compare

      900EN: 5-Port Ethernet Switch

      • 10/100Mbps
      • 15 to 36V DC power supply required
      • Five shielded RJ-45 sockets, 8-pin, 10Base-T / 100Base-TX
      $350
      Select options
    • Compare

      AMTN, AMTX: ActiveX / .NET Controls for Modbus I/O

      • Modbus/TCP or Modbus/RTU
      • These ActiveX / .NET software controls provide a fast, easy way to communicate with any Modbus slave devices connected to your PC.
      • Get your Visual Basic, Visual C, .NET, Excel, or other compatible applications talking Modbus protocol within minutes.
      $270$370
      Select options
    • Compare

      ESW-MBLIB: Ethernet Modbus C Library Software

      • Universal support for five operating systems
      • C source code provided
      • Demo program included
      $0$350
      Select options
    • Compare

      IMC-100A: 10/100BaseTX to 100BaseFX Industrial Media Converter

      • UTP to Fiber Media Converter
      • RJ45 Port Supports Auto MDI/MDI-X Function
       
      $250
      Select options
    • Compare

      PS5R: Slim Line Power Supplies

      • 10W, 15W, 30W, 60W, 90W, 120W, and 240W models
      • Universal Input (85-264V AC / 100-370V DC)
      • Lightweight and compact size
      $100$255
      Select options
    • Compare

      Terminal Block Replacements

      • Simplifies wiring connections on Acromag I/O Modules
      • Barrier strip or spring clamp terminal block kits
      • Provide safe and secure wiring connections
      $35$45
      Select options
    • Compare

      USB-to-Ethernet Adapter

      Simplifies configuration of Acromag Ethernet I/O Modules Prevents disruption of existing LANs This device is a USB-to-Ethernet adapter that you can use to communicate with any Acromag Ethernet I/O product for the purpose of setup and re-configuration for your application. It is recommended for initial communication with Acromag Ethernet devices so that you do not have to disrupt your existing network connection.
      $85
      Select options
  • Additional information

    Additional information

    Weight 10 oz
    Dimensions 4.5 × 1.5 × 5 in
    Part Number

    972EN-4004: Modbus TCP/IP and i2o protocol, 4 channel, 972EN-4006: Modbus TCP/IP and i2o protocol, 6 channel, 972EN-6004: Ethernet/IP, 4 channel, 972EN-6006, Ethernet/IP, 6 channel, 973EN-4004: Modbus TCP/IP and i2o protocol, 4 channel, 973EN-4006: Modbus TCP/IP and i2o protocol, 6 channel, 973EN-6004: Ethernet/IP, 4 channel, 973EN-6006: Ethernet/IP, 6 channel

    Communication

    Ethernet/IP, i2o Peer-to-Peer, Modbus TCP/IP

    Product Series

    BusWorks 900EN Series

    Configuration

    Built-in Web pages