Click to zoom
$755
Clear
Product short description:
  • 4 analog inputs
  • 2 analog output
  • 6 discrete I/O channels
  • Ethernet/IP, Modbus TCP/IP
  • i2o peer-to-peer available for Modbus TCP/IP only

These modules provide an isolated Ethernet network interface for analog and discrete I/O signals. Multi-range analog inputs and outputs support a wide variety of industrial devices. High-resolution, low noise, A/D and D/A converters deliver high accuracy and reliability.

Kindly go to setting page and check the option "Place them manually"

951EN: Combo module, analog current inputs
952EN: Combo module, analog voltage inputs

These Ethernet analog and discrete I/O modules provide an isolated Ethernet network interface for analog and discrete I/O signals. Multi-range analog inputs and outputs support a wide variety of industrial devices. High-resolution, low noise, A/D and D/A converters deliver high accuracy and reliability. 3-way isolation further improves system performance. The discrete I/O provide monitoring and control of on/off, high/low, or open/close industrial devices. Tandem I/O provides output level control and status verification in one unit.

The i2o function lets inputs on one module write directly to outputs on another module. Available for Modbus TCP/IP communication only.

Analog Input Ranges:
DC Current (user-selectable ranges)
0 to 1mA, 0 to 11mA, 0 to 20mA, 4 to 20mA
0 to 20 amps AC (with optional AC sensor)

DC Voltage (user-selectable ranges): ±1V, ±5V, ±10V DC

Analog Output Ranges
DC Current (user-selectable ranges)
0 to 1mA, 0 to 20mA, or 4 to 20mA
(0 to 625 ohm loads, typical)

Discrete I/O Range
0 to 35V DC active-high inputs
Current sourcing (high-side switched) outputs

Network Communication:
EtherNet/IP
Modbus TCP/IP, (i2o® peer-to-peer available for Modbus TCP/IP only)
10/100 network

Power Requirement: 15 to 36V DC supply (3.3 Watts) required

Approvals
CE/ATEX marked
UL, cUL listed, Class I; Div. 2; Groups A, B, C, D
EtherNet/IP, Modbus/TCP conformance tested

Performance Specifications

Analog Input

Configuration
Four input channels
Input range is selectable as a 4-channel group

Accuracy
Better than ±0.05% of span (0.1% for 0-1mA range), typical
Accuracy near or below 0mA or 0V is degraded if input COM shares AO/DIO RTNs

Analog to Digital Converter (A/D)
16-bit Σ-∆ converter
Resolution: 0.005% or 1 part in 20000

Noise Rejection
Normal Mode: Better than 40dB @ 60Hz
Common Mode: Better than 140dB @ 60Hz

Input Conversion Rate: Less than 50mS per channel

Input Impedance

DC current input (951EN): 49.9 ohms
DC voltage input (952EN): Greater than 110.5K ohms

Analog Output

Configuration
Two output channels
Individually selectable ranges

Accuracy: Better than ±0.05% of span (0.1% for 0-1mA range), typical

Digital to Analog Converter (D/A): 16-bit converter

Current Output Compliance: 12V minimum, 13V typical

Current Output Load Resistance Range: 0 to 625 ohms, typical

Discrete Input

Input Type
Six independent, active-high, buffered inputs with a common connection
Built-in 5.6K ohm pull-down resistors socketed for 3-channel groups

Input Signal Voltage Range: 0 to 35V DC, maximum

Input Impedance: 100K ohms, typical

Input Signal Threshold: TTL compatible with 100mV of hysteresis, typical

Discrete Output

Output Type
Six independent, open-source, MOSFET switches

Output Voltage and ON Resistance
Up to 35V DC maximum (0 to 330mA/ch continuous)
0.15 ohms maximum ON resistance

Environmental

Ambient Temperature and Humidity
Operating: -25 to 70°C (-13 to 158°F)
Storage: -40 to 85°C (-40 to 185°F)
Relative Humidity: 5 to 95%, non-condensing

Isolation
1500V AC for 60 seconds or 250V AC continuous
3-way isolation between I/O, network, and power

NOTE: i2o function only on Modbus TCP/IP modules

  • Configurable from a standard web browser
  • EtherNet/IP or Ethernet Modbus TCP/IP communication with automatic 10/100Mbps negotiation
  • i2o function (available ONLY with Modbus TCP/IP) enables direct input-to-output communication without a network controller
  • Multi-function, multi-channel stand-alone module is very economical
  • High-resolution 16-bit sigma-delta A/D and D/A converters ensure precise measurements
  • 0-35V DC solid-state logic interface can monitor or control a wide variety of devices
  • Discrete I/O channels are individually configurable as inputs or outputs in any combination
  • Bi-directional discrete I/O facilitates read-back monitoring of the output state
  • Built-in 5.6K ohm pull-down SIP resistors (socketed)
  • Selectable failsafe modes (0%, off, last-state,or pre-defined) help prevent unsafe conditions
  • Compact packaging with pluggable terminals saves space and simplifies wiring
  • Wide operational temperature range permits installation in extreme environments: -25°C to 70°C (-13° to 158°F)
  • Approvals: CE/ATEX marked; UL, cUL listed, Class 1 Div 2 Groups A, B, C, D; EtherNet/IP, Modbus/TCP conformance tested.
How to Connect Acromag Series 9xxEN Modules Via RadioLinx Ethernet Modems
Objective: The purpose of this document is to provide a procedure for connecting an Acromag Series 9xxEN I/O Module to an existing network via RadioLinx Ethernet Modems. Background – IP Addresses Any TCP/IP packet contains two addresses: a unique fixed MAC address, and a unique IP address. To communicate on the Internet, computers must have...
How to Monitor a Remote Geothermal Steam Well for Power Generation Application Note
Defining the Problem: Operations at a remote geothermal steam well are monitored by a PLC from the power plant. C&I personnel need to transmit conditions from the wellsite to the control room 2km away. A wireless communications network is available for Ethernet remote I/O. The modules can be installed at the wellsite for telemetry purposes....
How to Communicate with Acromag Modbus/TCP Modules from Ignition Software Application Note
Communicating with Ignition Software This document illustrates a procedure for configuring OPC tags intended for Acromag Busworks® Series Modbus/TCP modules using Windows software from Inductive Automation. It is assumed that the user has a working knowledge of OPC, Modbus TCP, and Ignition software. Product Features: BusWorks® Series 9xxEN Modules w/Modbus/TCP BusWorks® Series XT1xx1 Modules w/...
How to Connect to Acromag Ethernet I/O Devices Application Note
Getting Connected to Acromag Ethernet I/O Devices These instructions summarize the basic steps you will have to take in order to initially connect an Acromag Ethernet I/O product to your Personal Computer (PC) or laptop. To connect an Ethernet device to your PC, consult with your network administrator and either temporarily change the TCP/IP configuration...
How to Connect Acromag Series 900EN Ethernet Modules to Your PC Application Note
Objective: The purpose of this document is to provide a procedure for assigning a unique IP address to a second network interface card installed in a personal computer for the purpose of communicating with an Acromag Series 9xxEN Ethernet I/O Module. A procedure for accomplishing IP address assignment is provided using Windows 98, Windows ME, Windows...
How to Communicate with Acromag Series 9xxEN-60xx Ethernet Modules from Compact Logix Devices Application Note
Communicating with Acromag Series 9xxEN-60xx Ethernet Modules from Compact Logix Controllers This document illustrates a procedure for configuring message commands intended for Acromag Busworks® Series Ethernet/IP modules using ladder logic programming software and a Compact Logix Programmable Controller. It is assumed that the user has a working knowledge of ladder logic programming, the RSLogix5000 software,...
How to Communicate to Acromag Series 9xxEN-6xxx & XTxx2-xxx Ethernet Modules in an Allen Bradley ControlLogix System Application Note
Ethernet Modules in a ControlLogix System Objective: This document illustrates a procedure for integrating the Acromag Series 9xxEN-6xxx modules into the Allen Bradley control system as a third-party generic module. The reference model for this procedure is the Model 961EN-6006. It is assumed that the Acromag module has been assigned a static IP address and...
How to Configure Kepware KEPServerEX 5.0 for Communications with Acromag BusWorks Modbus I/O Modules Application Note
Configuring Kepware KEPServerEX 5.0 for Communications with Acromag BusWorks Modbus I/O modules. Introduction This document provides example steps for configuring the Kepware KEPServerEX OPC Server for communications with Acromag Busworks Modbus RTU and Modbus TCP/IP Distributed I/O Modules. Once the server is configured, data may be read from or written to the I/O module using...
How to Configure LabVIEW 2009 to Communicate with Acromag BusWorks and EtherStax Modbus I/O Modules Via an OPC Server Application Note
Introduction National Instruments LabVIEW can be used to monitor and control Acromag Busworks and Etherstax Modbus I/O Modules via an OPC server. A separate application note, Configuring Kepware KEPServerEX 5.0 for Communications with Acromag Busworks and Etherstax Modbus I/O Modules, outlines configuration of a KEPServerEX OPC server. This document focuses on setting up controls and...
How to Configure Omron CJ2H PLC's with Ethernet/IP for Use with Acromag Ethernet/IP Remote I/O Application Note
Purpose: Acromag Ethernet/IP I/O with Omron CJ2H PLC’s This document walks the user through the configuration of the Cx-One Network Configurator software that is used in conjunction with Omron CJ2H PLC’s. It is assumed that the user has a working knowledge of the PLC and Cx-One software. Configuring the CxOne “Network Configurator” Start the Cx-One...
How to Communicate to Acromag Series 9xxEN-60xx Ethernet Modules using PCCC from Compact Logix Devices Application Note
PCCC Messaging with CompactLogix This document illustrates a procedure for configuring PCCC message commands for Acromag Series 9xxEN Ethernet/IP modules using ladder logic programming and a Compact Logix Controller. It is assumed that the user has a working knowledge of ladder logic programming, the RSLogix5000 software, and the Compact Logix hardware. Configuring PCCC Messaging Using...
How to Communicate to Ethernet Modules from Legacy Allen Bradley or Rockwell Automation Devices Application Note
This document illustrates a procedure for configuring message commands for Acromag Series 9xxEN Ethernet/IP modules using ladder logic programming and an SLC5\05 Programmable Logic Controller. It is assumed that the user has a working knowledge of ladder logic programming, the RSLogix500 software, and the SLC 5\05 hardware. Setup of PCCC Communication to Series 9xxEN-60xx I/O...
How to Configure the Wonderware MBENET I/O Server to Communicate with the Acromag 9xxEN Ethernet Modules Application Note
Wonderware MBENET The purpose of this document is to provide a procedure for configuring MBENET I/O Server (ie: Modicon Ethernet I/O Server) to communicate with an Acromag Series 9xxEN Ethernet I/O Module. It is assumed that the user has a working knowledge of Wonderware and how to link the Wonderware application to the Wonderware I/O...
How to Communicate to Acromag Series Ethernet Modules from Red Lion HMIs Application Note
Red Lion HMIs This document illustrates a procedure for configuring message commands for Acromag Ethernet modules using the Red Lion Crimson 2.0 Software. It is assumed that the user has a working knowledge of the Crimson 2.0 software, as well as a Red Lion HMI. Setting up Communications From a new or existing project, double...

Manuals

951EN-4012 / 952EN-4012 User Manual (Log in to download the file)

951EN-6012 / 952EN-6012 User Manual (Log in to download the file)

ESW-MBLIB-DEMO (Log in to download the file)
ATMX Demo Software (Log in to download the file)
AMTN-DEMO (Log in to download the file)
Ethernet IP EDS for 9xxEN-6xxx Modules (Log in to download the file)
  • Compare

    20RM-16-DIN: 19” rack-mount kit with DIN rail

    • 19" rack-mount kit with DIN rail
    $185
    Select options
  • Compare

    5020-350: Toroidal AC Current Sensor

    • AC Current Sensor to precondition an AC current input signal
    • Highly accurate toroidal instrument transformer that converts an AC current signal to a safe, low level, DC milliampere signal (0 to 11.17mA).
    $50
    Select options
  • Compare

    5035 Series: Ethernet Cables

    • Ethernet straight cable, CAT5
    • Ethernet crossover cable, CAT5E
    • Low EMI Double-Shielded Ethernet Patch Cable
    $40$115
    Select options
  • Compare

    900EN: 5-Port Ethernet Switch

    • 10/100Mbps
    • 15 to 36V DC power supply required
    • Five shielded RJ-45 sockets, 8-pin, 10Base-T / 100Base-TX
    $340
    Select options
  • Compare

    AMTN, AMTX: ActiveX / .NET Controls for Modbus I/O

    • Modbus/TCP or Modbus/RTU
    • These ActiveX / .NET software controls provide a fast, easy way to communicate with any Modbus slave devices connected to your PC.
    • Get your Visual Basic, Visual C, .NET, Excel, or other compatible applications talking Modbus protocol within minutes.
    $260$350
    Select options
  • Compare

    ESW-MBLIB: Ethernet Modbus C Library Software

    • Universal support for five operating systems
    • C source code provided
    • Demo program included
    $0$330
    Read more
  • Compare

    IMC-100A: 10/100BaseTX to 100BaseFX Industrial Media Converter

    • UTP to Fiber Media Converter
    • RJ45 Port Supports Auto MDI/MDI-X Function
    $240
    Select options
  • Compare

    PS5R: Slim Line Power Supplies

    • 10W, 15W, 30W, 60W, 90W, 120W, and 240W models
    • Universal Input (85-264V AC / 100-370V DC)
    • Lightweight and compact size
    $95$245
    Select options
  • Compare

    Terminal Block Replacements

    • Simplifies wiring connections on Acromag I/O Modules
    • Barrier strip or spring clamp terminal block kits
    • Provide safe and secure wiring connections
    $30$40
    Select options
  • Compare

    USB-to-Ethernet Adapter

    Simplifies configuration of Acromag Ethernet I/O Modules Prevents disruption of existing LANs This device is a USB-to-Ethernet adapter that you can use to communicate with any Acromag Ethernet I/O product for the purpose of setup and re-configuration for your application. It is recommended for initial communication with Acromag Ethernet devices so that you do not have to disrupt your existing network connection.
    $80
    Select options

Additional information

Weight N/A
Dimensions 12 × 13 × 3 in
Part Number

4001-096: USB Ethernet Adapter

  • Description

    Standards

    USB 1.0, 1.1, 2.0 IEEE 802.3, IEEE 802.3u

    Ports One Type-A Male Connector, One RJ-45 Port
    LEDs Link/Activity

    Cabling
    Type Cat 5 Ethernet Cable

    Dimensions
    7.96” x 1.00” x 0.69” (202.3 x 25.35 x 17.65 mm)

    Weight
    0.8 oz (23 kg)

    Power
    3.3V low power consumption

    Certification
    FCC Class B, CE Class B, UL

    Operating Temp.
    32 to 158°F (0 to 70°C)

    Storage Temp.
    32 to 158°F (0 to 70°C)

    Operating Humidity
    10 to 90% non-condensing

    Storage Humidity
    10 to 90% non-condensing

    Includes: Package Contents

    • One USB Ethernet Adapter
    • One Driver Installation CD
    • One Quick Installation Guide
    • One User Guide included on Installation CD
    • One Acromag Ethernet I/O Instruction Sheet
    • One IP Address Batch Configuration CD
  • Features & Benefits

    • Configurable from a standard web browser
    • EtherNet/IP or Ethernet Modbus TCP/IP communication with automatic 10/100Mbps negotiation
    • i2o function (available ONLY with Modbus TCP/IP) enables direct input-to-output communication without a network controller
    • Multi-function, multi-channel stand-alone module is very economical
    • High-resolution 16-bit sigma-delta A/D and D/A converters ensure precise measurements
    • 0-35V DC solid-state logic interface can monitor or control a wide variety of devices
    • Discrete I/O channels are individually configurable as inputs or outputs in any combination
    • Bi-directional discrete I/O facilitates read-back monitoring of the output state
    • Built-in 5.6K ohm pull-down SIP resistors (socketed)
    • Selectable failsafe modes (0%, off, last-state,or pre-defined) help prevent unsafe conditions
    • Compact packaging with pluggable terminals saves space and simplifies wiring
    • Wide operational temperature range permits installation in extreme environments: -25°C to 70°C (-13° to 158°F)
    • Approvals: CE/ATEX marked; UL, cUL listed, Class 1 Div 2 Groups A, B, C, D; EtherNet/IP, Modbus/TCP conformance tested.
  • Tech Papers

    How to Connect Acromag Series 9xxEN Modules Via RadioLinx Ethernet Modems
    Objective: The purpose of this document is to provide a procedure for connecting an Acromag Series 9xxEN I/O Module to an existing network via RadioLinx Ethernet Modems. Background – IP Addresses Any TCP/IP packet contains two addresses: a unique fixed MAC address, and a unique IP address. To communicate on the Internet, computers must have...
    How to Monitor a Remote Geothermal Steam Well for Power Generation Application Note
    Defining the Problem: Operations at a remote geothermal steam well are monitored by a PLC from the power plant. C&I personnel need to transmit conditions from the wellsite to the control room 2km away. A wireless communications network is available for Ethernet remote I/O. The modules can be installed at the wellsite for telemetry purposes....
    How to Communicate with Acromag Modbus/TCP Modules from Ignition Software Application Note
    Communicating with Ignition Software This document illustrates a procedure for configuring OPC tags intended for Acromag Busworks® Series Modbus/TCP modules using Windows software from Inductive Automation. It is assumed that the user has a working knowledge of OPC, Modbus TCP, and Ignition software. Product Features: BusWorks® Series 9xxEN Modules w/Modbus/TCP BusWorks® Series XT1xx1 Modules w/...
    How to Connect to Acromag Ethernet I/O Devices Application Note
    Getting Connected to Acromag Ethernet I/O Devices These instructions summarize the basic steps you will have to take in order to initially connect an Acromag Ethernet I/O product to your Personal Computer (PC) or laptop. To connect an Ethernet device to your PC, consult with your network administrator and either temporarily change the TCP/IP configuration...
    How to Connect Acromag Series 900EN Ethernet Modules to Your PC Application Note
    Objective: The purpose of this document is to provide a procedure for assigning a unique IP address to a second network interface card installed in a personal computer for the purpose of communicating with an Acromag Series 9xxEN Ethernet I/O Module. A procedure for accomplishing IP address assignment is provided using Windows 98, Windows ME, Windows...
    How to Communicate with Acromag Series 9xxEN-60xx Ethernet Modules from Compact Logix Devices Application Note
    Communicating with Acromag Series 9xxEN-60xx Ethernet Modules from Compact Logix Controllers This document illustrates a procedure for configuring message commands intended for Acromag Busworks® Series Ethernet/IP modules using ladder logic programming software and a Compact Logix Programmable Controller. It is assumed that the user has a working knowledge of ladder logic programming, the RSLogix5000 software,...
    How to Communicate to Acromag Series 9xxEN-6xxx & XTxx2-xxx Ethernet Modules in an Allen Bradley ControlLogix System Application Note
    Ethernet Modules in a ControlLogix System Objective: This document illustrates a procedure for integrating the Acromag Series 9xxEN-6xxx modules into the Allen Bradley control system as a third-party generic module. The reference model for this procedure is the Model 961EN-6006. It is assumed that the Acromag module has been assigned a static IP address and...
    How to Configure Kepware KEPServerEX 5.0 for Communications with Acromag BusWorks Modbus I/O Modules Application Note
    Configuring Kepware KEPServerEX 5.0 for Communications with Acromag BusWorks Modbus I/O modules. Introduction This document provides example steps for configuring the Kepware KEPServerEX OPC Server for communications with Acromag Busworks Modbus RTU and Modbus TCP/IP Distributed I/O Modules. Once the server is configured, data may be read from or written to the I/O module using...
    How to Configure LabVIEW 2009 to Communicate with Acromag BusWorks and EtherStax Modbus I/O Modules Via an OPC Server Application Note
    Introduction National Instruments LabVIEW can be used to monitor and control Acromag Busworks and Etherstax Modbus I/O Modules via an OPC server. A separate application note, Configuring Kepware KEPServerEX 5.0 for Communications with Acromag Busworks and Etherstax Modbus I/O Modules, outlines configuration of a KEPServerEX OPC server. This document focuses on setting up controls and...
    How to Configure Omron CJ2H PLC's with Ethernet/IP for Use with Acromag Ethernet/IP Remote I/O Application Note
    Purpose: Acromag Ethernet/IP I/O with Omron CJ2H PLC’s This document walks the user through the configuration of the Cx-One Network Configurator software that is used in conjunction with Omron CJ2H PLC’s. It is assumed that the user has a working knowledge of the PLC and Cx-One software. Configuring the CxOne “Network Configurator” Start the Cx-One...
    How to Communicate to Acromag Series 9xxEN-60xx Ethernet Modules using PCCC from Compact Logix Devices Application Note
    PCCC Messaging with CompactLogix This document illustrates a procedure for configuring PCCC message commands for Acromag Series 9xxEN Ethernet/IP modules using ladder logic programming and a Compact Logix Controller. It is assumed that the user has a working knowledge of ladder logic programming, the RSLogix5000 software, and the Compact Logix hardware. Configuring PCCC Messaging Using...
    How to Communicate to Ethernet Modules from Legacy Allen Bradley or Rockwell Automation Devices Application Note
    This document illustrates a procedure for configuring message commands for Acromag Series 9xxEN Ethernet/IP modules using ladder logic programming and an SLC5\05 Programmable Logic Controller. It is assumed that the user has a working knowledge of ladder logic programming, the RSLogix500 software, and the SLC 5\05 hardware. Setup of PCCC Communication to Series 9xxEN-60xx I/O...
    How to Configure the Wonderware MBENET I/O Server to Communicate with the Acromag 9xxEN Ethernet Modules Application Note
    Wonderware MBENET The purpose of this document is to provide a procedure for configuring MBENET I/O Server (ie: Modicon Ethernet I/O Server) to communicate with an Acromag Series 9xxEN Ethernet I/O Module. It is assumed that the user has a working knowledge of Wonderware and how to link the Wonderware application to the Wonderware I/O...
    How to Communicate to Acromag Series Ethernet Modules from Red Lion HMIs Application Note
    Red Lion HMIs This document illustrates a procedure for configuring message commands for Acromag Ethernet modules using the Red Lion Crimson 2.0 Software. It is assumed that the user has a working knowledge of the Crimson 2.0 software, as well as a Red Lion HMI. Setting up Communications From a new or existing project, double...
  • Specs & Data Sheets

    Manuals

    951EN-4012 / 952EN-4012 User Manual (Log in to download the file)

    951EN-6012 / 952EN-6012 User Manual (Log in to download the file)

  • Software

    ESW-MBLIB-DEMO (Log in to download the file)
    ATMX Demo Software (Log in to download the file)
    AMTN-DEMO (Log in to download the file)
    Ethernet IP EDS for 9xxEN-6xxx Modules (Log in to download the file)
  • Accessories

    • Compare

      20RM-16-DIN: 19” rack-mount kit with DIN rail

      • 19" rack-mount kit with DIN rail
      $185
      Select options
    • Compare

      5020-350: Toroidal AC Current Sensor

      • AC Current Sensor to precondition an AC current input signal
      • Highly accurate toroidal instrument transformer that converts an AC current signal to a safe, low level, DC milliampere signal (0 to 11.17mA).
      $50
      Select options
    • Compare

      5035 Series: Ethernet Cables

      • Ethernet straight cable, CAT5
      • Ethernet crossover cable, CAT5E
      • Low EMI Double-Shielded Ethernet Patch Cable
      $40$115
      Select options
    • Compare

      900EN: 5-Port Ethernet Switch

      • 10/100Mbps
      • 15 to 36V DC power supply required
      • Five shielded RJ-45 sockets, 8-pin, 10Base-T / 100Base-TX
      $340
      Select options
    • Compare

      AMTN, AMTX: ActiveX / .NET Controls for Modbus I/O

      • Modbus/TCP or Modbus/RTU
      • These ActiveX / .NET software controls provide a fast, easy way to communicate with any Modbus slave devices connected to your PC.
      • Get your Visual Basic, Visual C, .NET, Excel, or other compatible applications talking Modbus protocol within minutes.
      $260$350
      Select options
    • Compare

      ESW-MBLIB: Ethernet Modbus C Library Software

      • Universal support for five operating systems
      • C source code provided
      • Demo program included
      $0$330
      Read more
    • Compare

      IMC-100A: 10/100BaseTX to 100BaseFX Industrial Media Converter

      • UTP to Fiber Media Converter
      • RJ45 Port Supports Auto MDI/MDI-X Function
      $240
      Select options
    • Compare

      PS5R: Slim Line Power Supplies

      • 10W, 15W, 30W, 60W, 90W, 120W, and 240W models
      • Universal Input (85-264V AC / 100-370V DC)
      • Lightweight and compact size
      $95$245
      Select options
    • Compare

      Terminal Block Replacements

      • Simplifies wiring connections on Acromag I/O Modules
      • Barrier strip or spring clamp terminal block kits
      • Provide safe and secure wiring connections
      $30$40
      Select options
    • Compare

      USB-to-Ethernet Adapter

      Simplifies configuration of Acromag Ethernet I/O Modules Prevents disruption of existing LANs This device is a USB-to-Ethernet adapter that you can use to communicate with any Acromag Ethernet I/O product for the purpose of setup and re-configuration for your application. It is recommended for initial communication with Acromag Ethernet devices so that you do not have to disrupt your existing network connection.
      $80
      Select options
  • Additional information

    Additional information

    Weight N/A
    Dimensions 12 × 13 × 3 in
    Part Number

    4001-096: USB Ethernet Adapter