IP480: Counter/Timer Module
Product short description:
- Two or six 16-bit (one or three 32-bit) counter/timer channels
- Event counter
- Output waveform generator
- Pulse-width or periodic rate monitor
- Watchdog timer with isolated relay output
- Interrupt support
IP480 modules provide up to six counter/timer channels for counting events, generating waveform control signals, measuring pulse-widths or periodic rates, and monitoring operations.
Support for internal or external triggering simplifies the synchronization of operations to specific events. Counter functions can use internally generated clocks or an externally supplied clock.
Not recommended for new designs
Specifications
Counter/Timers
Counter/timer configuration:
IP480-6: Six 16-bit counter/timer function groups.
IP480-2: Two 16-bit counter/timer function groups.
Any two 16-bit counters may be combined together to create a 32-bit counter.
Speed (with 8MHz internal clock):
Max. output pulse/square wave freq.: 4MHz.
Minimum event pulse width: 130nS.
Minimum pulse width measurement: 250nS.
Minimum period measurement: 250nS.
Mode accuracy (with external clocking):
Waveform generation: Period is ±62nS.
Watchdog: Timeout occurs within ±1 clock cycle.
Pulse/period measurement: ±1 clock cycle.
Internal clocks: Programmable 1, 4, or 8MHz.
External clocks: Separate clock input for each counter supports frequencies up to 7MHz.
Counter trigger: External inputs for triggering counter functions.
Input level is TTL or CMOS compatible. Vih=2.0V, Vil=0.8V. Inputs are buffered and include 4.7K ohm pull-ups to +5V.
Input voltage range: 0 to 5V.
Input requirements: 2.0V DC minimum high level, 0.8V DC maximum low level, 10μA maximum current.
Output: Non-isolated open drains of N-channel mosfets with socketed 4.7K ohms pull-up resistor SIP. Drains protected to 60V DC and sink up to 250mA each.
Output range (low side switch): 0 to 5V with internal supply. 0 to 60V with pull-ups to external supply.
Output open drain pull-ups: A 4.7K ohms pull-up resistor SIP. Power limited to 0.15W/resistor.
Output relays: SPDT (Form C) electromechanical relays (one per counter) controlled in watchdog timer mode. Contacts rated to 125V AC, 1A.
IP Compliance (ANSI/VITA 4)
Meets all written IP specs per ANSI/VITA 4-1995.
IP data transfer cycle types supported: Input/output (IOSel*), ID read (IDSel*), Interrupt select (INTSel*).
Access times (8MHz clock):
Read/write cycles: 0 wait states (250ns cycle);
1 wait state (375nS cycle) to read the counter readback register.
Environmental
Operating temperature: 0 to 70°C (IP480-2/6) or -40 to 85°C (IP480-2E/6E).
Storage temperature: -55 to 125°C (all models).
Relative Humidity: 5 to 95% non-condensing.
MTBF: Consult factory.
Power: +5V (±5%): 255mA max. (-6), 110mA (-2).
±12V (±5%) from P1: 0mA max. (not used).
- IP480-6: Six 16-bit (three 32-bit) counter/timers
- IP480-2: Two 16-bit (one 32-bit) counter/timers
- Event counters
- Output waveform generator
- continuous pulse
- single pulse
- continuous square waveforms
- Pulse-width or periodic rate monitor
- Watchdog timer with isolated relay output
- Interrupt support:
- watchdog timeout
- event count complete
- pulse-width or rate measurement complete
- pulse wave complete
- successive waveform generation
- Extended temperature option (-40 to 85°C)
Specs & Catalogs
Manuals
IP480 User Manual (Log in to download the file)
Catalogs
Drawings & Diagrams
-
502x Cable Series
- Communication Signal Cables
- Wide assortment of ribbon cables
$40 – $600Select options -
Conformal Coating
Moisture and humidity protection for boards via Acromag applied conformal coating using acrylic resin (Humiseal 1B31).$55Select options -
CS-IP Conformal Coat
Industry Pack conformal coat. This option should be selected to prevent high temperature and humidity issues (like blotching) when boards are conformal coated$75Select options -
IPSW-API: I/O Function Routines for VxWorks, Windows, Linux
- Use with IndustryPack modules/carriers
- Easy installation procedure
- Help files with step-by-step instructions
- Demonstration Program
- Driver level support for desktop and embedded Windows level programming environments
$375 – $1,005Select options -
Termination Products
- DIN rail-mount panels
- 50 screw terminals on 50-pin connector termination panels
- 50 screw terminals on SCSI-2 connector termination panels
- 68 screw terminals on SCSI-3 connector termination panels
$165 – $225Select options
Additional information
Weight | 8 oz |
---|---|
Dimensions | 4 × 2 × 1 in |
Part Number | IP480-2: 2 16-bit (1 32-bit) counter/timers., IP480-2E: 2 16-bit (1 32-bit) counter/timers, extended temp. range., IP480-6: 6 16-bit (3 32-bit) counter/timers., IP480-6E: 6-bit (3 32-bit) counter/timers,extended temp. range. |
Product Series | Industry Pack |
-
Description
IP480 modules provide up to six counter/timer channels for counting events, generating waveform control signals, measuring pulse-widths or periodic rates, and monitoring operations.
Support for internal or external triggering simplifies the synchronization of operations to specific events. Counter functions can use internally generated clocks or an externally supplied clock.
Not recommended for new designs
Specifications
Counter/Timers
Counter/timer configuration:
IP480-6: Six 16-bit counter/timer function groups.
IP480-2: Two 16-bit counter/timer function groups.
Any two 16-bit counters may be combined together to create a 32-bit counter.Speed (with 8MHz internal clock):
Max. output pulse/square wave freq.: 4MHz.
Minimum event pulse width: 130nS.
Minimum pulse width measurement: 250nS.
Minimum period measurement: 250nS.Mode accuracy (with external clocking):
Waveform generation: Period is ±62nS.
Watchdog: Timeout occurs within ±1 clock cycle.
Pulse/period measurement: ±1 clock cycle.Internal clocks: Programmable 1, 4, or 8MHz.
External clocks: Separate clock input for each counter supports frequencies up to 7MHz.Counter trigger: External inputs for triggering counter functions.
Input level is TTL or CMOS compatible. Vih=2.0V, Vil=0.8V. Inputs are buffered and include 4.7K ohm pull-ups to +5V.Input voltage range: 0 to 5V.
Input requirements: 2.0V DC minimum high level, 0.8V DC maximum low level, 10μA maximum current.
Output: Non-isolated open drains of N-channel mosfets with socketed 4.7K ohms pull-up resistor SIP. Drains protected to 60V DC and sink up to 250mA each.
Output range (low side switch): 0 to 5V with internal supply. 0 to 60V with pull-ups to external supply.
Output open drain pull-ups: A 4.7K ohms pull-up resistor SIP. Power limited to 0.15W/resistor.
Output relays: SPDT (Form C) electromechanical relays (one per counter) controlled in watchdog timer mode. Contacts rated to 125V AC, 1A.IP Compliance (ANSI/VITA 4)
Meets all written IP specs per ANSI/VITA 4-1995.
IP data transfer cycle types supported: Input/output (IOSel*), ID read (IDSel*), Interrupt select (INTSel*).
Access times (8MHz clock):
Read/write cycles: 0 wait states (250ns cycle);
1 wait state (375nS cycle) to read the counter readback register.Environmental
Operating temperature: 0 to 70°C (IP480-2/6) or -40 to 85°C (IP480-2E/6E).
Storage temperature: -55 to 125°C (all models).
Relative Humidity: 5 to 95% non-condensing.
MTBF: Consult factory.
Power: +5V (±5%): 255mA max. (-6), 110mA (-2).
±12V (±5%) from P1: 0mA max. (not used). -
Features & Benefits
- IP480-6: Six 16-bit (three 32-bit) counter/timers
- IP480-2: Two 16-bit (one 32-bit) counter/timers
- Event counters
- Output waveform generator
- continuous pulse
- single pulse
- continuous square waveforms
- Pulse-width or periodic rate monitor
- Watchdog timer with isolated relay output
- Interrupt support:
- watchdog timeout
- event count complete
- pulse-width or rate measurement complete
- pulse wave complete
- successive waveform generation
- Extended temperature option (-40 to 85°C)
-
Specs & Data Sheets
Specs & Catalogs
Manuals
IP480 User Manual (Log in to download the file)
Catalogs
Drawings & Diagrams
-
Software
IPSW-API-LNX (Log in to download the file) -
Accessories
-
502x Cable Series
- Communication Signal Cables
- Wide assortment of ribbon cables
$40 – $600Select options -
Conformal Coating
Moisture and humidity protection for boards via Acromag applied conformal coating using acrylic resin (Humiseal 1B31).$55Select options -
CS-IP Conformal Coat
Industry Pack conformal coat. This option should be selected to prevent high temperature and humidity issues (like blotching) when boards are conformal coated$75Select options -
IPSW-API: I/O Function Routines for VxWorks, Windows, Linux
- Use with IndustryPack modules/carriers
- Easy installation procedure
- Help files with step-by-step instructions
- Demonstration Program
- Driver level support for desktop and embedded Windows level programming environments
$375 – $1,005Select options -
Termination Products
- DIN rail-mount panels
- 50 screw terminals on 50-pin connector termination panels
- 50 screw terminals on SCSI-2 connector termination panels
- 68 screw terminals on SCSI-3 connector termination panels
$165 – $225Select options
-
-
Additional information
Additional information
Weight 8 oz Dimensions 4 × 2 × 1 in Part Number IP480-2: 2 16-bit (1 32-bit) counter/timers., IP480-2E: 2 16-bit (1 32-bit) counter/timers, extended temp. range., IP480-6: 6 16-bit (3 32-bit) counter/timers., IP480-6E: 6-bit (3 32-bit) counter/timers,extended temp. range.
Product Series Industry Pack
Please login to submit this form.