IP511: Serial Communication, 422 Isolated Industry Pack Module
Product short description:
- Four asynchronous EIA/TIA-422B isolated serial ports
- 16 or 64-byte FIFO buffers
- Interrupt support
- Programmable baud rate (up to 512Kbps)
Not recommended for new designs. Limited availability - please contact sales department.
IP511 Industry Pack (IP) modules provide an isolated, asynchronous serial communication interface for your computer system.
Large FIFO buffers on the transmit and receive lines of each serial port enable more efficient data processing. When the buffer is full, an interrupt is sent to the CPU to read the data. To match your budget and performance requirements, you can order 16 or 64-byte (IP511-16/64) buffers.
Specifications
Serial Ports
Configuration: 4 independent, isolated, full-duplex, RS422B ports.
Interface: Asynchronous serial only.
Data rate: Programmable to 512K bits/second. Consult factory for custom baud rates up to 1M baud.
Character size: Programmable 5-8 bits.
Parity: Programmable odd, even, or no parity.
Stop bits: Programmable 1, 1-1/2, or 2 bits.
Data register buffers: Double-buffered (16C450 mode) or 16/64-byte FIFO buffered.
Interrupts: Receiver Line Status, Received Data Available or Character Timeout, Transmitter Holding Register Empty. IP511-64 includes interrupts for received XOFF signal/special character.
Receiver input resistance: 12K ohms minimum.
Differential input threshold: ±0.2V.
Bias resistors: Not required (driver always enabled).
Output short circuit current: 250mA maximum.
Termination resistors 120 ohms, socketed.
Maximum cable length: 1200m (4000 ft.).
Port power requirements: Isolated +5V ±5%, 5mA typical, each port.
UART
IP511-16: Texas Inst. TL16C554FN or equivalent.
IP511-64: Startech ST16C654CJ68.
IP Compliance (ANSI/VITA 4)
Meets IP specifications per ANSI/VITA 4-1995.
IP data transfer cycle types supported: Input/output (IOSel*), ID read (IDSel*), Interrupt select (INTSel*).
Access times (8MHz clock):
ID PROM read: 1 wait state (375nS cycle).
I/O register read/write: 2 wait states (500nS cycle).
Interrupt select read: 2 wait states (500nS cycle).
Environmental
Operating temperature: 0 to 70°C.
Storage temperature: -40 to 125°C.
Relative humidity: 5 to 95% non-condensing.
Power:
+5V (±5%): 160mA maximum.
±12V (±5%): 0mA (not used).
MTBF: Consult factory.
- Four asynchronous EIA/TIA-422B ports
- Isolated serial ports
- 16 or 64-byte FIFO buffers
- Programmable baud rate (up to 512Kbps) (Consult factory for custom rates up to 1Mbps)
- Individually controlled interrupts (unique vectors for each port)
- Line break generation and detection
- False start bit detection
- Industry-standard 16C550 UART including software compatible 16C450 mode
- 0 to 70°C
- Isolation protects computer system from ground loops and transient signals.
- FIFO buffers minimize CPU interaction for more effcient data processing.
- Internal diagnostics help detect communication faults.
- Priority shifting scheme prevents continuous interrupts from blocking other ports.
Specs & Catalogs
Manuals
IP511 User Manual (Log in to download the file)
Catalogs
Drawings & Diagrams
-
502x Cable Series
- Communication Signal Cables
- Wide assortment of ribbon cables
$40 – $600Select options -
Conformal Coating
Moisture and humidity protection for boards via Acromag applied conformal coating using acrylic resin (Humiseal 1B31).$55Select options -
CS-IP Conformal Coat
Industry Pack conformal coat. This option should be selected to prevent high temperature and humidity issues (like blotching) when boards are conformal coated$75Select options -
IPSW-API: I/O Function Routines for VxWorks, Windows, Linux
- Use with IndustryPack modules/carriers
- Easy installation procedure
- Help files with step-by-step instructions
- Demonstration Program
- Driver level support for desktop and embedded Windows level programming environments
$375 – $1,005Select options -
Termination Products
- DIN rail-mount panels
- 50 screw terminals on 50-pin connector termination panels
- 50 screw terminals on SCSI-2 connector termination panels
- 68 screw terminals on SCSI-3 connector termination panels
$165 – $225Select options
Additional information
Weight | 8 oz |
---|---|
Dimensions | 4 × 2 × 1 in |
Part Number | IP511-16: 16-byte FIFO buffers., IP511-64: 64-byte FIFO buffers. |
Product Series | Industry Pack |
-
Description
IP511 Industry Pack (IP) modules provide an isolated, asynchronous serial communication interface for your computer system.
Large FIFO buffers on the transmit and receive lines of each serial port enable more efficient data processing. When the buffer is full, an interrupt is sent to the CPU to read the data. To match your budget and performance requirements, you can order 16 or 64-byte (IP511-16/64) buffers.
Specifications
Serial Ports
Configuration: 4 independent, isolated, full-duplex, RS422B ports.
Interface: Asynchronous serial only.
Data rate: Programmable to 512K bits/second. Consult factory for custom baud rates up to 1M baud.
Character size: Programmable 5-8 bits.
Parity: Programmable odd, even, or no parity.
Stop bits: Programmable 1, 1-1/2, or 2 bits.
Data register buffers: Double-buffered (16C450 mode) or 16/64-byte FIFO buffered.
Interrupts: Receiver Line Status, Received Data Available or Character Timeout, Transmitter Holding Register Empty. IP511-64 includes interrupts for received XOFF signal/special character.
Receiver input resistance: 12K ohms minimum.
Differential input threshold: ±0.2V.
Bias resistors: Not required (driver always enabled).
Output short circuit current: 250mA maximum.
Termination resistors 120 ohms, socketed.
Maximum cable length: 1200m (4000 ft.).
Port power requirements: Isolated +5V ±5%, 5mA typical, each port.UART
IP511-16: Texas Inst. TL16C554FN or equivalent.
IP511-64: Startech ST16C654CJ68.IP Compliance (ANSI/VITA 4)
Meets IP specifications per ANSI/VITA 4-1995.
IP data transfer cycle types supported: Input/output (IOSel*), ID read (IDSel*), Interrupt select (INTSel*).
Access times (8MHz clock):
ID PROM read: 1 wait state (375nS cycle).
I/O register read/write: 2 wait states (500nS cycle).
Interrupt select read: 2 wait states (500nS cycle).Environmental
Operating temperature: 0 to 70°C.
Storage temperature: -40 to 125°C.
Relative humidity: 5 to 95% non-condensing.
Power:
+5V (±5%): 160mA maximum.
±12V (±5%): 0mA (not used).
MTBF: Consult factory. -
Features & Benefits
- Four asynchronous EIA/TIA-422B ports
- Isolated serial ports
- 16 or 64-byte FIFO buffers
- Programmable baud rate (up to 512Kbps) (Consult factory for custom rates up to 1Mbps)
- Individually controlled interrupts (unique vectors for each port)
- Line break generation and detection
- False start bit detection
- Industry-standard 16C550 UART including software compatible 16C450 mode
- 0 to 70°C
- Isolation protects computer system from ground loops and transient signals.
- FIFO buffers minimize CPU interaction for more effcient data processing.
- Internal diagnostics help detect communication faults.
- Priority shifting scheme prevents continuous interrupts from blocking other ports.
-
Specs & Data Sheets
Specs & Catalogs
Manuals
IP511 User Manual (Log in to download the file)
Catalogs
Drawings & Diagrams
-
Software
IPSW-API-LNX (Log in to download the file) -
Accessories
-
502x Cable Series
- Communication Signal Cables
- Wide assortment of ribbon cables
$40 – $600Select options -
Conformal Coating
Moisture and humidity protection for boards via Acromag applied conformal coating using acrylic resin (Humiseal 1B31).$55Select options -
CS-IP Conformal Coat
Industry Pack conformal coat. This option should be selected to prevent high temperature and humidity issues (like blotching) when boards are conformal coated$75Select options -
IPSW-API: I/O Function Routines for VxWorks, Windows, Linux
- Use with IndustryPack modules/carriers
- Easy installation procedure
- Help files with step-by-step instructions
- Demonstration Program
- Driver level support for desktop and embedded Windows level programming environments
$375 – $1,005Select options -
Termination Products
- DIN rail-mount panels
- 50 screw terminals on 50-pin connector termination panels
- 50 screw terminals on SCSI-2 connector termination panels
- 68 screw terminals on SCSI-3 connector termination panels
$165 – $225Select options
-
-
Additional information
Additional information
Weight 8 oz Dimensions 4 × 2 × 1 in Part Number IP511-16: 16-byte FIFO buffers., IP511-64: 64-byte FIFO buffers.
Product Series Industry Pack
Please login to submit this form.