IP502: Serial Communication, 485 Half-Duplex Industry Pack Modules
Product short description:
- Four asynchronous EIA-485 serial ports
- 16-byte FIFO buffers
- Interrupt support
- Programmable baud rate (up to 512Kbps)
Not recommended for new designs. Limited availability - please contact sales department.
These modules provide an asynchronous serial communication interface for your system. The IP502 has four asynchronous, half-duplex RS485 serial ports. It provides a cost-efficient interface to RS485 multi-driver networks which support up to 32 nodes. However, for full handshaking support, use the full duplex IP501.
Software-configuration quickly sets the baud rate, character-size, stop bits, and parity.
For more efficient data processing, each serial port is equipped with 16-character FIFO buffers on the transmit and receive lines.
Specifications
RS485 Serial Ports
Configuration: Four independent, non-isolated RS485 serial ports with a common single return connection.
Data rate: Programmable up to 512Kbps using internal baud rate generator and carrier 8MHz clock. Consult factory for custom baud rates up to 1M baud.
Interface: Asynchronous serial only.
Max. cable length: 1200 meters (4000 feet) typical. A signal repeater can extend this limit.
Character size: 5 to 8 bits, software-programmable.
Parity: Odd, even, or no parity; software-programmable.
Stop bits: 1, 1-1/2, or 2 bits; software-programmable.
Data register buffers: 16-byte receive FIFO buffers and 16-byte transmit FIFO buffers.
Interrupts: Receiver line status (overrun error, parity error, framing error, or break interrupt); received data available (FIFO level reached) or character time-out; transmitter holding register empty. Multiple ports share the IntReq0 line according to a shifting priority scheme based on the last interrupting port serviced.
UART
UART: Texas Instruments TL16C554FN.
IP Compliance (ANSI/VITA 4)
Meets IP specifications per ANSI/VITA 4-1995.
IP data transfer cycle types supported: Input/output (IOSel*), ID read (IDSel*).
Access times (8MHz clock):
ID PROM read: 1 wait state (375nS cycle).
Channel register read/write: 2 wait states (500nS cycle).
Interrupt select read: 2 wait states.
Environmental
Operating temperature: 0 to 70°C.
Storage temperature: -40 to 125°C.
Relative humidity: 5 to 95% non-condensing.
Power:
+5V (±5%): 300mA maximum.
±12V (±5%) from P1: 0mA (not used)
MTBF: 7,642,747 hrs at 25°C, MIL-HDBK-217F, Notice 2.
- Four asynchronous, half-duplex EIA-485 serial ports
- 16-byte FIFO buffers
- Programmable baud rate (up to 512Kbps) (Consult factory for custom rates up to 1M bps)
- Individually controlled interrupts (unique vectors for each port)
- Line-break and false start-bit detection
- Industry-standard 16C550 family UART includes software-compatible 16C450 mode
- 0 to 70°C
- Failsafe receivers guarantee a high output state when the inputs are left open or floating.
- Internal diagnostics help detect communication faults.
- 16-byte FIFO buffers minimize CPU interaction for improved system performance.
Specs & Catalogs
Manuals
IP502 User Manual (Log in to download the file)
Catalogs
Drawings & Diagrams
-
502x Cable Series
- Communication Signal Cables
- Wide assortment of ribbon cables
$40 – $600Select options -
Conformal Coating
Moisture and humidity protection for boards via Acromag applied conformal coating using acrylic resin (Humiseal 1B31).$55Select options -
CS-IP Conformal Coat
Industry Pack conformal coat. This option should be selected to prevent high temperature and humidity issues (like blotching) when boards are conformal coated$75Select options -
IPSW-API: I/O Function Routines for VxWorks, Windows, Linux
- Use with IndustryPack modules/carriers
- Easy installation procedure
- Help files with step-by-step instructions
- Demonstration Program
- Driver level support for desktop and embedded Windows level programming environments
$375 – $1,005Select options -
Termination Products
- DIN rail-mount panels
- 50 screw terminals on 50-pin connector termination panels
- 50 screw terminals on SCSI-2 connector termination panels
- 68 screw terminals on SCSI-3 connector termination panels
$165 – $225Select options
Additional information
Weight | 8 oz |
---|---|
Dimensions | 4 × 2 × 1 in |
Part Number | IP502: Non-isolated communication module |
Product Series | Industry Pack |
-
Description
These modules provide an asynchronous serial communication interface for your system. The IP502 has four asynchronous, half-duplex RS485 serial ports. It provides a cost-efficient interface to RS485 multi-driver networks which support up to 32 nodes. However, for full handshaking support, use the full duplex IP501.
Software-configuration quickly sets the baud rate, character-size, stop bits, and parity.
For more efficient data processing, each serial port is equipped with 16-character FIFO buffers on the transmit and receive lines.
Specifications
RS485 Serial Ports
Configuration: Four independent, non-isolated RS485 serial ports with a common single return connection.
Data rate: Programmable up to 512Kbps using internal baud rate generator and carrier 8MHz clock. Consult factory for custom baud rates up to 1M baud.
Interface: Asynchronous serial only.
Max. cable length: 1200 meters (4000 feet) typical. A signal repeater can extend this limit.
Character size: 5 to 8 bits, software-programmable.
Parity: Odd, even, or no parity; software-programmable.
Stop bits: 1, 1-1/2, or 2 bits; software-programmable.
Data register buffers: 16-byte receive FIFO buffers and 16-byte transmit FIFO buffers.
Interrupts: Receiver line status (overrun error, parity error, framing error, or break interrupt); received data available (FIFO level reached) or character time-out; transmitter holding register empty. Multiple ports share the IntReq0 line according to a shifting priority scheme based on the last interrupting port serviced.UART
UART: Texas Instruments TL16C554FN.
IP Compliance (ANSI/VITA 4)
Meets IP specifications per ANSI/VITA 4-1995.
IP data transfer cycle types supported: Input/output (IOSel*), ID read (IDSel*).
Access times (8MHz clock):
ID PROM read: 1 wait state (375nS cycle).
Channel register read/write: 2 wait states (500nS cycle).
Interrupt select read: 2 wait states.Environmental
Operating temperature: 0 to 70°C.
Storage temperature: -40 to 125°C.
Relative humidity: 5 to 95% non-condensing.
Power:
+5V (±5%): 300mA maximum.
±12V (±5%) from P1: 0mA (not used)
MTBF: 7,642,747 hrs at 25°C, MIL-HDBK-217F, Notice 2. -
Features & Benefits
- Four asynchronous, half-duplex EIA-485 serial ports
- 16-byte FIFO buffers
- Programmable baud rate (up to 512Kbps) (Consult factory for custom rates up to 1M bps)
- Individually controlled interrupts (unique vectors for each port)
- Line-break and false start-bit detection
- Industry-standard 16C550 family UART includes software-compatible 16C450 mode
- 0 to 70°C
- Failsafe receivers guarantee a high output state when the inputs are left open or floating.
- Internal diagnostics help detect communication faults.
- 16-byte FIFO buffers minimize CPU interaction for improved system performance.
-
Specs & Data Sheets
Specs & Catalogs
Manuals
IP502 User Manual (Log in to download the file)
Catalogs
Drawings & Diagrams
-
Software
IPSW-API-LNX (Log in to download the file) -
Accessories
-
502x Cable Series
- Communication Signal Cables
- Wide assortment of ribbon cables
$40 – $600Select options -
Conformal Coating
Moisture and humidity protection for boards via Acromag applied conformal coating using acrylic resin (Humiseal 1B31).$55Select options -
CS-IP Conformal Coat
Industry Pack conformal coat. This option should be selected to prevent high temperature and humidity issues (like blotching) when boards are conformal coated$75Select options -
IPSW-API: I/O Function Routines for VxWorks, Windows, Linux
- Use with IndustryPack modules/carriers
- Easy installation procedure
- Help files with step-by-step instructions
- Demonstration Program
- Driver level support for desktop and embedded Windows level programming environments
$375 – $1,005Select options -
Termination Products
- DIN rail-mount panels
- 50 screw terminals on 50-pin connector termination panels
- 50 screw terminals on SCSI-2 connector termination panels
- 68 screw terminals on SCSI-3 connector termination panels
$165 – $225Select options
-
-
Additional information
Additional information
Weight 8 oz Dimensions 4 × 2 × 1 in Part Number IP502: Non-isolated communication module
Product Series Industry Pack
Please login to submit this form.