Click to zoom
$890$1,430

Please sign in or register to see model options and to add products to your cart.

Product short description:
  • 8 or 16 voltage output channels
  • Independent D/A converter on each channel
  • 11µS settling time
  • ±10V output range

The IP220A outputs analog voltage signals to drive up to 16 devices. When used with a carrier that holds four IP modules, up to 64 voltage outputs can be obtained from a single card cage slot.

Each output channel has its own 12-bit D/A converter (DAC). Individual DACs are faster, and they eliminate glitches typically caused by the re-acquisition process of sample and holds found on multiplexed output boards.

Individual channels also have double-buffered data latches. You can select to update each output when it is written to, or to update all outputs simultaneously. Simultaneous outputs better simulate linear movements in motion processes.

The IP220A is a drop-in replacement for the IP220, please see the known differences document below for more information.
Known difference between the IP220 and the IP220A statement

Specifications

Analog Outputs

Output configuration: 8 or 16 single-ended.
D/A Resolution: 12 bits.
Output range: Bipolar, -10 to +10V.
Settling time: 11μS.
Maximum throughput rate:
Outputs can be updated simultaneously or individually.
One channel: 11μS/conversion.
Sixteen channels simultaneously: 17μS/16 channels.
System accuracy: 0.025% of 20V span maximum corrected error (i.e. calibrated) at 25°C with the output unloaded.
Data format (left–justified): Bipolar Offset Binary.
Output at reset: 0 volts.
Output current: -5 to +5mA (maximum). This corresponds to a minimum load resistance of 5K ohms with a 10V output.
Short circuit protection: Indefinite at 25°C.

IP Compliance (ANSI/VITA 4)

Meets IP specifications per ANSI/VITA 4-1995.
IP data transfer cycle types supported: Input/output (IOSel*): DAC data, control registers, DAC offset and gain calibration coefficients. ID read (IDSel*): 32 x 8 ID PROM.
Access Times (8MHz clock):
ID EEPROM read: 0 wait states (250nS cycle).
DAC channel data write: 1 wait states (375nS cycle).
DAC offset/gain coeff. read: 1 wait states (375nS cycle).
Control register access: 1 wait states (375nS cycle).

Environmental

Operating temperature: 0 to 70°C (IP220-8/16) or -40 to 85°C (IP220-8E/16E models).
Storage temperature: -55 to 100°C (all models).
Relative humidity: 5 to 95% non-condensing.
MTBF: 4,094,686 hrs. at 25°C, MIL-HDBK-217F, notice 2.
Power:
+5V: 33mA typical,45mA Maximum.
+12V from P1: 150mA typical,200mA maximum.
-12V from P1: 133mA typical,180mA maximum.

 

  • 8 or 16 analog voltage output channels
  • Independent 12-bit D/A converters per channel with an 11.0µS settling time
  • Bipolar voltage (non-isolated) outputs: -10 to +10 volts
  • Double-buffered DACs
  • High load capability (5mA output current)
  • Built-in calibration coefficients
  • 0 to 70°C (IP220-8/16) or -40 to 85°C (IP220-8E/16E models)
  • Outputs reset to 0 volts.
  • Internally stored calibration coefficients ensure accuracy.
  • Software provides easy selection of transparent or simultaneous output modes.
  • Double-buffered DACs allow new data to be written to each channel before the simultaneous trigger updates the outputs.

Manuals

IP220A User Manual (Log in to download the file)

Known differences between the IP220 and the IP220A (Log in to download the file)

Drawings & Diagrams

IPSW-API-LNX (Log in to download the file)
  • Compare

    502x Cable Series

    • Communication Signal Cables
    • Wide assortment of ribbon cables
    $45$705
    Select options
  • Compare

    Conformal Coating

    Moisture and humidity protection for boards via Acromag applied conformal coating using acrylic resin (Humiseal 1B31).  
    $60
    Select options
  • Compare

    CS-IP Conformal Coat

    Industry Pack conformal coat. This option should be selected to prevent high temperature and humidity issues (like blotching) when boards are conformal coated
    $80
    Select options
  • Compare

    IPSW-API: I/O Function Routines for VxWorks, Windows, Linux

    • Use with IndustryPack modules/carriers
    • Easy installation procedure
    • Help files with step-by-step instructions
    • Demonstration Program
    • Driver level support for desktop and embedded Windows level programming environments
    $385$1,035
    Select options
  • Compare

    Termination Products

    • DIN rail-mount panels
    • 50 screw terminals on 50-pin connector termination panels
    • 50 screw terminals on SCSI-2 connector termination panels
    • 68 screw terminals on SCSI-3 connector termination panels
    $170$245
    Select options
  • Compare

    Transition Modules

    • Various transition modules
    $250$1,085
    Select options

Additional information

Weight 8 oz
Dimensions 4 × 2 × 1 in
Part Number

IP220A-16: 16 channels, IP220A-16E: 16 channels; extended temp. range, IP220A-8: 8 channels, IP220A-8E: 8 channels; extended temp. range

Product Series

Industry Pack

  • Description

    The IP220A outputs analog voltage signals to drive up to 16 devices. When used with a carrier that holds four IP modules, up to 64 voltage outputs can be obtained from a single card cage slot.

    Each output channel has its own 12-bit D/A converter (DAC). Individual DACs are faster, and they eliminate glitches typically caused by the re-acquisition process of sample and holds found on multiplexed output boards.

    Individual channels also have double-buffered data latches. You can select to update each output when it is written to, or to update all outputs simultaneously. Simultaneous outputs better simulate linear movements in motion processes.

    The IP220A is a drop-in replacement for the IP220, please see the known differences document below for more information.
    Known difference between the IP220 and the IP220A statement

    Specifications

    Analog Outputs

    Output configuration: 8 or 16 single-ended.
    D/A Resolution: 12 bits.
    Output range: Bipolar, -10 to +10V.
    Settling time: 11μS.
    Maximum throughput rate:
    Outputs can be updated simultaneously or individually.
    One channel: 11μS/conversion.
    Sixteen channels simultaneously: 17μS/16 channels.
    System accuracy: 0.025% of 20V span maximum corrected error (i.e. calibrated) at 25°C with the output unloaded.
    Data format (left–justified): Bipolar Offset Binary.
    Output at reset: 0 volts.
    Output current: -5 to +5mA (maximum). This corresponds to a minimum load resistance of 5K ohms with a 10V output.
    Short circuit protection: Indefinite at 25°C.

    IP Compliance (ANSI/VITA 4)

    Meets IP specifications per ANSI/VITA 4-1995.
    IP data transfer cycle types supported: Input/output (IOSel*): DAC data, control registers, DAC offset and gain calibration coefficients. ID read (IDSel*): 32 x 8 ID PROM.
    Access Times (8MHz clock):
    ID EEPROM read: 0 wait states (250nS cycle).
    DAC channel data write: 1 wait states (375nS cycle).
    DAC offset/gain coeff. read: 1 wait states (375nS cycle).
    Control register access: 1 wait states (375nS cycle).

    Environmental

    Operating temperature: 0 to 70°C (IP220-8/16) or -40 to 85°C (IP220-8E/16E models).
    Storage temperature: -55 to 100°C (all models).
    Relative humidity: 5 to 95% non-condensing.
    MTBF: 4,094,686 hrs. at 25°C, MIL-HDBK-217F, notice 2.
    Power:
    +5V: 33mA typical,45mA Maximum.
    +12V from P1: 150mA typical,200mA maximum.
    -12V from P1: 133mA typical,180mA maximum.

     

  • Features & Benefits

    • 8 or 16 analog voltage output channels
    • Independent 12-bit D/A converters per channel with an 11.0µS settling time
    • Bipolar voltage (non-isolated) outputs: -10 to +10 volts
    • Double-buffered DACs
    • High load capability (5mA output current)
    • Built-in calibration coefficients
    • 0 to 70°C (IP220-8/16) or -40 to 85°C (IP220-8E/16E models)
    • Outputs reset to 0 volts.
    • Internally stored calibration coefficients ensure accuracy.
    • Software provides easy selection of transparent or simultaneous output modes.
    • Double-buffered DACs allow new data to be written to each channel before the simultaneous trigger updates the outputs.
  • Specs & Data Sheets

    Manuals

    IP220A User Manual (Log in to download the file)

    Known differences between the IP220 and the IP220A (Log in to download the file)

    Drawings & Diagrams

  • Software

    IPSW-API-LNX (Log in to download the file)
  • Accessories

    • Compare

      502x Cable Series

      • Communication Signal Cables
      • Wide assortment of ribbon cables
      $45$705
      Select options
    • Compare

      Conformal Coating

      Moisture and humidity protection for boards via Acromag applied conformal coating using acrylic resin (Humiseal 1B31).  
      $60
      Select options
    • Compare

      CS-IP Conformal Coat

      Industry Pack conformal coat. This option should be selected to prevent high temperature and humidity issues (like blotching) when boards are conformal coated
      $80
      Select options
    • Compare

      IPSW-API: I/O Function Routines for VxWorks, Windows, Linux

      • Use with IndustryPack modules/carriers
      • Easy installation procedure
      • Help files with step-by-step instructions
      • Demonstration Program
      • Driver level support for desktop and embedded Windows level programming environments
      $385$1,035
      Select options
    • Compare

      Termination Products

      • DIN rail-mount panels
      • 50 screw terminals on 50-pin connector termination panels
      • 50 screw terminals on SCSI-2 connector termination panels
      • 68 screw terminals on SCSI-3 connector termination panels
      $170$245
      Select options
    • Compare

      Transition Modules

      • Various transition modules
      $250$1,085
      Select options
  • Additional information

    Additional information

    Weight 8 oz
    Dimensions 4 × 2 × 1 in
    Part Number

    IP220A-16: 16 channels, IP220A-16E: 16 channels; extended temp. range, IP220A-8: 8 channels, IP220A-8E: 8 channels; extended temp. range

    Product Series

    Industry Pack