Click to zoom
$1,705$1,825
Clear
Product short description:
  • 8 voltage output channels
  • Individual D/A converters on each channel
  • 10µS settling time
  • Selectable output range (±5V, ±10V, 0-10V)
RSS
FACEBOOK
FACEBOOK
TWITTER
Visit Us
LINKEDIN

IP235A modules have a 16-bit D/A converter (DAC) to provide highly-accurate analog voltage outputs. An internal RAM buffer enhances control over the transfer of data to the DAC.

Each channel has a dedicated 2K sample RAM buffer. All channels share a global clock. A start trigger transfers digital values from the buffer to the DAC. Four modes offer several choices for the data transfer. Continuous mode simultaneously updates all the channels by cycling through the buffer until a software halt command is received. Single-cycle mode simultaneously updates all channels but only cycles through the buffer once for each start trigger.

The IP235A is a drop-in replacement for the IP235, please see the known differences document below for more information.
Known differences between the IP235 and the IP235A.

Specifications

Analog Outputs

Output configuration: 8
D/A Resolution: 16 bits.
Output ranges: ±5V, ±10V, 0 to 10V (jumper-selectable).
Data sample memory: 2K sample RAM buffer on each channel.
Maximum throughput rate: Outputs can be updated simultaneously or individually. One channel: 100KHz (10µS/conversion). Eight channels: 100KHz (10µS/8 ch).
DAC programming: Immediate (transparently programmed to DAC output); simultaneous (input latches of multiple DACs are loaded with new data before simultaneously updating outputs).
System accuracy: 0.0061% of 20V span maximum corrected error (i.e. calibrated) at 25°C with the output unloaded.
Output at reset: 0V for bipolar output, 5V for unipolar.
Output current: -5 to +5mA (maximum).
Short circuit protection: Indefinite at 25°C.

IP Compliance (ANSI/VITA 4)

Meets IP specifications per ANSI/VITA 4-1995.
IP data transfer cycle types supported: Input/output (IOSel*), ID read (IDSel*), Interrupt select (INTsel*).
Access times (8MHz clock): 1 wait state (375nS cycle).

Environmental

Operating temperature: 0 to 70°C (IP235-8A) or -40 to 85°C (IP235A-8E models).
Storage temperature: -55 to 125°C (all models).
Relative humidity: 5 to 95% non-condensing
MTBF: 815,720 hrs at 25°C, MIL-HDBK-217F, Notice 2.
Power: +5V (±5%): 250mA maximum. ±12V (±5%) from P1: 150mA maximum.

  • 8 analog voltage outputs
  • Individual 16-bit D/A converters per channel
  • Global timer for all channels supporting clock rates of up to 100KHz
  • Waveform memory (2K samples/channel)
  • Software, external, or internal timer triggers
  • Interrupt capability
  • External trigger output
  • User-programmable interval timer
  • 0 to 70°C (IP235-8) or -40 to 85°C (IP235-8E models)

Manuals

IP231 User Manual (Log in to download the file)

Known Difference Statement for IP230/235/236 and PMC230 (Log in to download the file)

Drawings & Diagrams

IPSW-API-LNX (Log in to download the file)
  • Compare

    502x Cable Series

    • Communication Signal Cables
    • Wide assortment of ribbon cables
    $40$600
    Select options
  • Compare

    IPSW-API: I/O Function Routines for VxWorks, Windows, Linux

    • Use with IndustryPack modules/carriers
    • Easy installation procedure
    • Help files with step-by-step instructions
    • Demonstration Program
    • Driver level support for desktop and embedded Windows level programming environments
    $365$1,005
    Read more
  • Compare

    Termination Products

    • DIN rail-mount panels
    • 50 screw terminals on 50-pin connector termination panels
    • 50 screw terminals on SCSI-2 connector termination panels
    • 68 screw terminals on SCSI-3 connector termination panels
    $165$210
    Select options
  • Compare

    Transition Modules

    • Various transition modules
    $220$890
    Select options

Additional information

Weight N/A
Dimensions N/A
Part Number

TRANS-200: Use with AVME9670 & AVME9670E, TRANS-C100: Use with AcPC8635, TRANS-C200: Use with ACPC8625, XBRD-9060-LF: Expansion I/O Carrier Module, XVME-9640-1-LF: Transition Module with P0 connector, XVME-9640-2-LF: Transition Module without P0 connector, TRANS-C4610: Use with AcPC4610, TRANS-C4620: Use with AcPC4620E and AcPC4620CC, TRANS-C5200: Use with AcPC4620E and AcPC4620CC with 128 CMOS I/O, TRANS-C5201: Use with AcPC4620E and AcPC4620CC with 64 EIA485 I/O channels, TRANS-C5210: Use with AcPC8625, VPX4500-RTM-LF: Use with VPX4500E-LF and VPX4500-CC-LF, TRANS-V112-LF: Rear transition module for the VPX4812 / VPX4814

  • Description

    These adapters repeat field I/O connections on Acromag’s carrier cards for front or rear exit from the card cage.

    Transition modules provide a solution for controlling the location of your cabling within the card cage.

    TRANS-200: Transition module
    Transition module for AVME9670 board. See AVME9670 manual for more information.

    VPX4500-RTM-LF: Rear transition module used with both the VPX4500E-LF and the VPX4500-CC-LF carriers to provide access to the slot C AcroPack field I/O signals. See carrier card user manual for more information

     

     

  • Features & Benefits

    • 8 analog voltage outputs
    • Individual 16-bit D/A converters per channel
    • Global timer for all channels supporting clock rates of up to 100KHz
    • Waveform memory (2K samples/channel)
    • Software, external, or internal timer triggers
    • Interrupt capability
    • External trigger output
    • User-programmable interval timer
    • 0 to 70°C (IP235-8) or -40 to 85°C (IP235-8E models)
  • Specs & Data Sheets

    Manuals

    IP231 User Manual (Log in to download the file)

    Known Difference Statement for IP230/235/236 and PMC230 (Log in to download the file)

    Drawings & Diagrams

  • Software

    IPSW-API-LNX (Log in to download the file)
  • Accessories

    • Compare

      502x Cable Series

      • Communication Signal Cables
      • Wide assortment of ribbon cables
      $40$600
      Select options
    • Compare

      IPSW-API: I/O Function Routines for VxWorks, Windows, Linux

      • Use with IndustryPack modules/carriers
      • Easy installation procedure
      • Help files with step-by-step instructions
      • Demonstration Program
      • Driver level support for desktop and embedded Windows level programming environments
      $365$1,005
      Read more
    • Compare

      Termination Products

      • DIN rail-mount panels
      • 50 screw terminals on 50-pin connector termination panels
      • 50 screw terminals on SCSI-2 connector termination panels
      • 68 screw terminals on SCSI-3 connector termination panels
      $165$210
      Select options
    • Compare

      Transition Modules

      • Various transition modules
      $220$890
      Select options
  • Additional information

    Additional information

    Weight N/A
    Dimensions N/A
    Part Number

    TRANS-200: Use with AVME9670 & AVME9670E, TRANS-C100: Use with AcPC8635, TRANS-C200: Use with ACPC8625, XBRD-9060-LF: Expansion I/O Carrier Module, XVME-9640-1-LF: Transition Module with P0 connector, XVME-9640-2-LF: Transition Module without P0 connector, TRANS-C4610: Use with AcPC4610, TRANS-C4620: Use with AcPC4620E and AcPC4620CC, TRANS-C5200: Use with AcPC4620E and AcPC4620CC with 128 CMOS I/O, TRANS-C5201: Use with AcPC4620E and AcPC4620CC with 64 EIA485 I/O channels, TRANS-C5210: Use with AcPC8625, VPX4500-RTM-LF: Use with VPX4500E-LF and VPX4500-CC-LF, TRANS-V112-LF: Rear transition module for the VPX4812 / VPX4814