Click to zoom
$865$1,395
Clear
Product short description:
  • 8 or 16 voltage output channels
  • Independent D/A converter on each channel
  • 11µS settling time
  • ±10V output range
RSS
FACEBOOK
FACEBOOK
TWITTER
Visit Us
LINKEDIN

The IP220A outputs analog voltage signals to drive up to 16 devices. When used with a carrier that holds four IP modules, up to 64 voltage outputs can be obtained from a single card cage slot.

Each output channel has its own 12-bit D/A converter (DAC). Individual DACs are faster, and they eliminate glitches typically caused by the re-acquisition process of sample and holds found on multiplexed output boards.

Individual channels also have double-buffered data latches. You can select to update each output when it is written to, or to update all outputs simultaneously. Simultaneous outputs better simulate linear movements in motion processes.

The IP220A is a drop-in replacement for the IP220, please see the known differences document below for more information.
Known difference between the IP220 and the IP220A statement

Specifications

Analog Outputs

Output configuration: 8 or 16 single-ended.
D/A Resolution: 12 bits.
Output range: Bipolar, -10 to +10V.
Settling time: 11μS.
Maximum throughput rate:
Outputs can be updated simultaneously or individually.
One channel: 11μS/conversion.
Sixteen channels simultaneously: 17μS/16 channels.
System accuracy: 0.025% of 20V span maximum corrected error (i.e. calibrated) at 25°C with the output unloaded.
Data format (left–justified): Bipolar Offset Binary.
Output at reset: 0 volts.
Output current: -5 to +5mA (maximum). This corresponds to a minimum load resistance of 5K ohms with a 10V output.
Short circuit protection: Indefinite at 25°C.

IP Compliance (ANSI/VITA 4)

Meets IP specifications per ANSI/VITA 4-1995.
IP data transfer cycle types supported: Input/output (IOSel*): DAC data, control registers, DAC offset and gain calibration coefficients. ID read (IDSel*): 32 x 8 ID PROM.
Access Times (8MHz clock):
ID EEPROM read: 0 wait states (250nS cycle).
DAC channel data write: 1 wait states (375nS cycle).
DAC offset/gain coeff. read: 1 wait states (375nS cycle).
Control register access: 1 wait states (375nS cycle).

Environmental

Operating temperature: 0 to 70°C (IP220-8/16) or -40 to 85°C (IP220-8E/16E models).
Storage temperature: -55 to 100°C (all models).
Relative humidity: 5 to 95% non-condensing.
MTBF: 4,094,686 hrs. at 25°C, MIL-HDBK-217F, notice 2.
Power:
+5V: 33mA typical,45mA Maximum.
+12V from P1: 150mA typical,200mA maximum.
-12V from P1: 133mA typical,180mA maximum.

 

  • 8 or 16 analog voltage output channels
  • Independent 12-bit D/A converters per channel with an 11.0µS settling time
  • Bipolar voltage (non-isolated) outputs: -10 to +10 volts
  • Double-buffered DACs
  • High load capability (5mA output current)
  • Built-in calibration coefficients
  • 0 to 70°C (IP220-8/16) or -40 to 85°C (IP220-8E/16E models)
  • Outputs reset to 0 volts.
  • Internally stored calibration coefficients ensure accuracy.
  • Software provides easy selection of transparent or simultaneous output modes.
  • Double-buffered DACs allow new data to be written to each channel before the simultaneous trigger updates the outputs.

Manuals

IP220A User Manual (Log in to download the file)

Known differences between the IP220 and the IP220A (Log in to download the file)

Drawings & Diagrams

IPSW-API-LNX (Log in to download the file)
  • Compare

    502x Cable Series

    • Communication Signal Cables
    • Wide assortment of ribbon cables
    $40$600
    Select options
  • Compare

    IPSW-API: I/O Function Routines for VxWorks, Windows, Linux

    • Use with IndustryPack modules/carriers
    • Easy installation procedure
    • Help files with step-by-step instructions
    • Demonstration Program
    • Driver level support for desktop and embedded Windows level programming environments
    $365$1,005
    Read more
  • Compare

    Termination Products

    • DIN rail-mount panels
    • 50 screw terminals on 50-pin connector termination panels
    • 50 screw terminals on SCSI-2 connector termination panels
    • 68 screw terminals on SCSI-3 connector termination panels
    $165$210
    Select options
  • Compare

    Transition Modules

    • Various transition modules
    $220$890
    Select options

Additional information

Weight N/A
Dimensions N/A
Part Number

TRANS-200: Use with AVME9670 & AVME9670E, TRANS-C100: Use with AcPC8635, TRANS-C200: Use with ACPC8625, XBRD-9060-LF: Expansion I/O Carrier Module, XVME-9640-1-LF: Transition Module with P0 connector, XVME-9640-2-LF: Transition Module without P0 connector, TRANS-C4610: Use with AcPC4610, TRANS-C4620: Use with AcPC4620E and AcPC4620CC, TRANS-C5200: Use with AcPC4620E and AcPC4620CC with 128 CMOS I/O, TRANS-C5201: Use with AcPC4620E and AcPC4620CC with 64 EIA485 I/O channels, TRANS-C5210: Use with AcPC8625, VPX4500-RTM-LF: Use with VPX4500E-LF and VPX4500-CC-LF, TRANS-V112-LF: Rear transition module for the VPX4812 / VPX4814

  • Description

    These adapters repeat field I/O connections on Acromag’s carrier cards for front or rear exit from the card cage.

    Transition modules provide a solution for controlling the location of your cabling within the card cage.

    TRANS-200: Transition module
    Transition module for AVME9670 board. See AVME9670 manual for more information.

    VPX4500-RTM-LF: Rear transition module used with both the VPX4500E-LF and the VPX4500-CC-LF carriers to provide access to the slot C AcroPack field I/O signals. See carrier card user manual for more information

     

     

  • Features & Benefits

    • 8 or 16 analog voltage output channels
    • Independent 12-bit D/A converters per channel with an 11.0µS settling time
    • Bipolar voltage (non-isolated) outputs: -10 to +10 volts
    • Double-buffered DACs
    • High load capability (5mA output current)
    • Built-in calibration coefficients
    • 0 to 70°C (IP220-8/16) or -40 to 85°C (IP220-8E/16E models)
    • Outputs reset to 0 volts.
    • Internally stored calibration coefficients ensure accuracy.
    • Software provides easy selection of transparent or simultaneous output modes.
    • Double-buffered DACs allow new data to be written to each channel before the simultaneous trigger updates the outputs.
  • Specs & Data Sheets

    Manuals

    IP220A User Manual (Log in to download the file)

    Known differences between the IP220 and the IP220A (Log in to download the file)

    Drawings & Diagrams

  • Software

    IPSW-API-LNX (Log in to download the file)
  • Accessories

    • Compare

      502x Cable Series

      • Communication Signal Cables
      • Wide assortment of ribbon cables
      $40$600
      Select options
    • Compare

      IPSW-API: I/O Function Routines for VxWorks, Windows, Linux

      • Use with IndustryPack modules/carriers
      • Easy installation procedure
      • Help files with step-by-step instructions
      • Demonstration Program
      • Driver level support for desktop and embedded Windows level programming environments
      $365$1,005
      Read more
    • Compare

      Termination Products

      • DIN rail-mount panels
      • 50 screw terminals on 50-pin connector termination panels
      • 50 screw terminals on SCSI-2 connector termination panels
      • 68 screw terminals on SCSI-3 connector termination panels
      $165$210
      Select options
    • Compare

      Transition Modules

      • Various transition modules
      $220$890
      Select options
  • Additional information

    Additional information

    Weight N/A
    Dimensions N/A
    Part Number

    TRANS-200: Use with AVME9670 & AVME9670E, TRANS-C100: Use with AcPC8635, TRANS-C200: Use with ACPC8625, XBRD-9060-LF: Expansion I/O Carrier Module, XVME-9640-1-LF: Transition Module with P0 connector, XVME-9640-2-LF: Transition Module without P0 connector, TRANS-C4610: Use with AcPC4610, TRANS-C4620: Use with AcPC4620E and AcPC4620CC, TRANS-C5200: Use with AcPC4620E and AcPC4620CC with 128 CMOS I/O, TRANS-C5201: Use with AcPC4620E and AcPC4620CC with 64 EIA485 I/O channels, TRANS-C5210: Use with AcPC8625, VPX4500-RTM-LF: Use with VPX4500E-LF and VPX4500-CC-LF, TRANS-V112-LF: Rear transition module for the VPX4812 / VPX4814