IP408: Digital Input/Output Module, High Voltage I/O
Product short description:
- 32 bi-directional digital input and/or output channels
- 0-60V DC input and output range
- Low-side output switches
- Outputs sink up to 1A per channel
- Change-of-state and level interrupts (up to 8 channels)
The IP408 monitors or controls the on/off (high/low) status of up to 32 devices. Each channel can be used as an input or output.
Input channels can be configured with interrupts for a change of state or level detection of any bit on up to 8 channels. The TTL input threshold includes hysteresis for increasing noise immunity.
In order to ensure safe, reliable control under all conditions, output operation is “fail-safe.” That is, the outputs are always off upon power-up and are automatically cleared following a software reset.
Loopback monitoring of critical control signals is easy since the input and output circuitry are connected in tandem to each channel.
Specifications
Digital Inputs
Input channel configuration: 32 noninverting buffered inputs with a common connection.
Input signal voltage range: 0 to 60V DC,maximum.
Input signal threshold: TTL compatible. 1.5V DC with 200mV of hysteresis, typ. Limited to TTL levels of 0.8V DC (max. low level) and 2.0V DC (minimum high level).
Input response time: 250nS minimum to 375nS max.
Interrupts: Change-of-state and level on channels 0-7.
Digital Outputs
Channel configuration: 32 open-drain DMOS MOSFETs with common source connection.
Output ON current range: 0 to 1A DC, continuous per channel (10A total for all channels combined). No deration required at elevated ambients.
Turn on time: 320nS typical (varies with load).
Turn off time: 500nS typical (varies with load).
IP Compliance (ANSI/VITA 4)
Meets IP specifications per ANSI/VITA 4-1995.
IP data transfer cycle types supported: Input/output (IOSel*), ID read (IDSel*).
Access Times (8MHz clock): 1 wait state (375nS cycle).
Interrupt handling format: An 8-bit vector is provided during interrupt acknowledge cycles on D0 – D7.
Updates: Two 16-bit read/writes to update all channels.
Environmental
Operating temperature: 0 to 70°C (IP408) or -40 to 85°C (IP408E).
Storage: -55 to 125°C (all models).
Relative Humidity: 5 to 95% non-condensing
MTBF: 1,317,013 hrs at 25°C, MIL-HDBK-217F, Notice 2.
Power: +5V (±5%): 50mA max. +12V (±5%) from P1: 8.5mA max. -12V (±5%) from P1: 0mA (not used).
- 32 digital input and/or output channels
- 0 to 60V DC input range, 60V DC low-side switch outputs
- Outputs sink up to 1A per channel
- TTL-compatible input threshold with hysteresis
- Change-of-state/level interrupts (up to 8)
- 0 to 70°C (IP408) or -40 to 85°C (IP408E)
- Buffered inputs include hysteresis to increase noise immunity.
- Interrupts are software-programmable for a change of state or level detection.
- Loopback monitoring enables self-test and fault diagnostics to detect open output switches or shorts.
- High impedance inputs prevent loading of the input source and minimize current.
- Individual outputs sink up to 1A DC continuous. No deration of output current required at elevated temperatures.
Specs & Catalogs
Manuals
IP408 User Manual (Log in to download the file)
Catalogs
Drawings & Diagrams
-
502x Cable Series
- Communication Signal Cables
- Wide assortment of ribbon cables
$40 – $600Select options -
Conformal Coating
Moisture and humidity protection for boards via Acromag applied conformal coating using acrylic resin (Humiseal 1B31).$55Select options -
CS-IP Conformal Coat
Industry Pack conformal coat. This option should be selected to prevent high temperature and humidity issues (like blotching) when boards are conformal coated$75Select options -
IPSW-API: I/O Function Routines for VxWorks, Windows, Linux
- Use with IndustryPack modules/carriers
- Easy installation procedure
- Help files with step-by-step instructions
- Demonstration Program
- Driver level support for desktop and embedded Windows level programming environments
$375 – $1,005Select options -
Termination Products
- DIN rail-mount panels
- 50 screw terminals on 50-pin connector termination panels
- 50 screw terminals on SCSI-2 connector termination panels
- 68 screw terminals on SCSI-3 connector termination panels
$165 – $225Select options
Additional information
Weight | 8 oz |
---|---|
Dimensions | 4 × 2 × 1 in |
Part Number | IP408: 0-60V DC input and output range., IP408E: 0-60V DC input and output range, extended temp. range. |
Product Series | Industry Pack |
-
Description
The IP408 monitors or controls the on/off (high/low) status of up to 32 devices. Each channel can be used as an input or output.
Input channels can be configured with interrupts for a change of state or level detection of any bit on up to 8 channels. The TTL input threshold includes hysteresis for increasing noise immunity.
In order to ensure safe, reliable control under all conditions, output operation is “fail-safe.” That is, the outputs are always off upon power-up and are automatically cleared following a software reset.
Loopback monitoring of critical control signals is easy since the input and output circuitry are connected in tandem to each channel.
Specifications
Digital Inputs
Input channel configuration: 32 noninverting buffered inputs with a common connection.
Input signal voltage range: 0 to 60V DC,maximum.
Input signal threshold: TTL compatible. 1.5V DC with 200mV of hysteresis, typ. Limited to TTL levels of 0.8V DC (max. low level) and 2.0V DC (minimum high level).
Input response time: 250nS minimum to 375nS max.
Interrupts: Change-of-state and level on channels 0-7.Digital Outputs
Channel configuration: 32 open-drain DMOS MOSFETs with common source connection.
Output ON current range: 0 to 1A DC, continuous per channel (10A total for all channels combined). No deration required at elevated ambients.
Turn on time: 320nS typical (varies with load).
Turn off time: 500nS typical (varies with load).IP Compliance (ANSI/VITA 4)
Meets IP specifications per ANSI/VITA 4-1995.
IP data transfer cycle types supported: Input/output (IOSel*), ID read (IDSel*).
Access Times (8MHz clock): 1 wait state (375nS cycle).
Interrupt handling format: An 8-bit vector is provided during interrupt acknowledge cycles on D0 – D7.
Updates: Two 16-bit read/writes to update all channels.Environmental
Operating temperature: 0 to 70°C (IP408) or -40 to 85°C (IP408E).
Storage: -55 to 125°C (all models).
Relative Humidity: 5 to 95% non-condensing
MTBF: 1,317,013 hrs at 25°C, MIL-HDBK-217F, Notice 2.
Power: +5V (±5%): 50mA max. +12V (±5%) from P1: 8.5mA max. -12V (±5%) from P1: 0mA (not used). -
Features & Benefits
- 32 digital input and/or output channels
- 0 to 60V DC input range, 60V DC low-side switch outputs
- Outputs sink up to 1A per channel
- TTL-compatible input threshold with hysteresis
- Change-of-state/level interrupts (up to 8)
- 0 to 70°C (IP408) or -40 to 85°C (IP408E)
- Buffered inputs include hysteresis to increase noise immunity.
- Interrupts are software-programmable for a change of state or level detection.
- Loopback monitoring enables self-test and fault diagnostics to detect open output switches or shorts.
- High impedance inputs prevent loading of the input source and minimize current.
- Individual outputs sink up to 1A DC continuous. No deration of output current required at elevated temperatures.
-
Specs & Data Sheets
Specs & Catalogs
Manuals
IP408 User Manual (Log in to download the file)
Catalogs
Drawings & Diagrams
-
Software
IPSW-API-LNX (Log in to download the file) -
Accessories
-
502x Cable Series
- Communication Signal Cables
- Wide assortment of ribbon cables
$40 – $600Select options -
Conformal Coating
Moisture and humidity protection for boards via Acromag applied conformal coating using acrylic resin (Humiseal 1B31).$55Select options -
CS-IP Conformal Coat
Industry Pack conformal coat. This option should be selected to prevent high temperature and humidity issues (like blotching) when boards are conformal coated$75Select options -
IPSW-API: I/O Function Routines for VxWorks, Windows, Linux
- Use with IndustryPack modules/carriers
- Easy installation procedure
- Help files with step-by-step instructions
- Demonstration Program
- Driver level support for desktop and embedded Windows level programming environments
$375 – $1,005Select options -
Termination Products
- DIN rail-mount panels
- 50 screw terminals on 50-pin connector termination panels
- 50 screw terminals on SCSI-2 connector termination panels
- 68 screw terminals on SCSI-3 connector termination panels
$165 – $225Select options
-
-
Additional information
Additional information
Weight 8 oz Dimensions 4 × 2 × 1 in Part Number IP408: 0-60V DC input and output range., IP408E: 0-60V DC input and output range, extended temp. range.
Product Series Industry Pack
Please login to submit this form.