Click to zoom
$600$880
Clear
Product short description:
  • Two or six 16-bit (one or three 32-bit) counter/timer channels
  • Event counter
  • Output waveform generator
  • Pulse-width or periodic rate monitor
  • Watchdog timer with isolated relay output
  • Interrupt support
RSS
FACEBOOK
FACEBOOK
TWITTER
Visit Us
LINKEDIN

IP480 modules provide up to six counter/timer channels for counting events, generating waveform control signals, measuring pulse-widths or periodic rates, and monitoring operations.

Support for internal or external triggering simplifies the synchronization of operations to specific events. Counter functions can use internally generated clocks or an externally supplied clock.

Not recommended for new designs

Specifications

Counter/Timers

Counter/timer configuration:
IP480-6: Six 16-bit counter/timer function groups.
IP480-2: Two 16-bit counter/timer function groups.
Any two 16-bit counters may be combined together to create a 32-bit counter.

Speed (with 8MHz internal clock):
Max. output pulse/square wave freq.: 4MHz.
Minimum event pulse width: 130nS.
Minimum pulse width measurement: 250nS.
Minimum period measurement: 250nS.

Mode accuracy (with external clocking):
Waveform generation: Period is ±62nS.
Watchdog: Timeout occurs within ±1 clock cycle.
Pulse/period measurement: ±1 clock cycle.

Internal clocks: Programmable 1, 4, or 8MHz.
External clocks: Separate clock input for each counter supports frequencies up to 7MHz.

Counter trigger: External inputs for triggering counter functions.
Input level is TTL or CMOS compatible. Vih=2.0V, Vil=0.8V. Inputs are buffered and include 4.7K ohm pull-ups to +5V.

Input voltage range: 0 to 5V.
Input requirements: 2.0V DC minimum high level, 0.8V DC maximum low level, 10μA maximum current.
Output: Non-isolated open drains of N-channel mosfets with socketed 4.7K ohms pull-up resistor SIP. Drains protected to 60V DC and sink up to 250mA each.
Output range (low side switch): 0 to 5V with internal supply. 0 to 60V with pull-ups to external supply.
Output open drain pull-ups: A 4.7K ohms pull-up resistor SIP. Power limited to 0.15W/resistor.
Output relays: SPDT (Form C) electromechanical relays (one per counter) controlled in watchdog timer mode. Contacts rated to 125V AC, 1A.

IP Compliance (ANSI/VITA 4)

Meets all written IP specs per ANSI/VITA 4-1995.
IP data transfer cycle types supported: Input/output (IOSel*), ID read (IDSel*), Interrupt select (INTSel*).
Access times (8MHz clock):
Read/write cycles: 0 wait states (250ns cycle);
1 wait state (375nS cycle) to read the counter readback register.

Environmental

Operating temperature: 0 to 70°C (IP480-2/6) or -40 to 85°C (IP480-2E/6E).
Storage temperature: -55 to 125°C (all models).
Relative Humidity: 5 to 95% non-condensing.
MTBF: Consult factory.
Power: +5V (±5%): 255mA max. (-6), 110mA (-2).
±12V (±5%) from P1: 0mA max. (not used).

  • IP480-6: Six 16-bit (three 32-bit) counter/timers
  • IP480-2: Two 16-bit (one 32-bit) counter/timers
  • Event counters
    • Output waveform generator
    • continuous pulse
    • single pulse
    • continuous square waveforms
  • Pulse-width or periodic rate monitor
  • Watchdog timer with isolated relay output
  • Interrupt support:
  • watchdog timeout
  • event count complete
  • pulse-width or rate measurement complete
  • pulse wave complete
  • successive waveform generation
  • Extended temperature option (-40 to 85°C)

Specs & Catalogs

Manuals

IP480 User Manual (Log in to download the file)

Drawings & Diagrams

IPSW-API-LNX (Log in to download the file)
  • Compare

    502x Cable Series

    • Communication Signal Cables
    • Wide assortment of ribbon cables
    $40$600
    Select options
  • Compare

    IPSW-API: I/O Function Routines for VxWorks, Windows, Linux

    • Use with IndustryPack modules/carriers
    • Easy installation procedure
    • Help files with step-by-step instructions
    • Demonstration Program
    • Driver level support for desktop and embedded Windows level programming environments
    $365$1,005
    Read more
  • Compare

    Termination Products

    • DIN rail-mount panels
    • 50 screw terminals on 50-pin connector termination panels
    • 50 screw terminals on SCSI-2 connector termination panels
    • 68 screw terminals on SCSI-3 connector termination panels
    $165$210
    Select options
  • Compare

    Transition Modules

    • Various transition modules
    $220$890
    Select options

Additional information

Weight N/A
Dimensions N/A
Part Number

TRANS-200: Use with AVME9670 & AVME9670E, TRANS-C100: Use with AcPC8635, TRANS-C200: Use with ACPC8625, XBRD-9060-LF: Expansion I/O Carrier Module, XVME-9640-1-LF: Transition Module with P0 connector, XVME-9640-2-LF: Transition Module without P0 connector, TRANS-C4610: Use with AcPC4610, TRANS-C4620: Use with AcPC4620E and AcPC4620CC, TRANS-C5200: Use with AcPC4620E and AcPC4620CC with 128 CMOS I/O, TRANS-C5201: Use with AcPC4620E and AcPC4620CC with 64 EIA485 I/O channels, TRANS-C5210: Use with AcPC8625, VPX4500-RTM-LF: Use with VPX4500E-LF and VPX4500-CC-LF, TRANS-V112-LF: Rear transition module for the VPX4812 / VPX4814

  • Description

    These adapters repeat field I/O connections on Acromag’s carrier cards for front or rear exit from the card cage.

    Transition modules provide a solution for controlling the location of your cabling within the card cage.

    TRANS-200: Transition module
    Transition module for AVME9670 board. See AVME9670 manual for more information.

    VPX4500-RTM-LF: Rear transition module used with both the VPX4500E-LF and the VPX4500-CC-LF carriers to provide access to the slot C AcroPack field I/O signals. See carrier card user manual for more information

     

     

  • Features & Benefits

    • IP480-6: Six 16-bit (three 32-bit) counter/timers
    • IP480-2: Two 16-bit (one 32-bit) counter/timers
    • Event counters
      • Output waveform generator
      • continuous pulse
      • single pulse
      • continuous square waveforms
    • Pulse-width or periodic rate monitor
    • Watchdog timer with isolated relay output
    • Interrupt support:
    • watchdog timeout
    • event count complete
    • pulse-width or rate measurement complete
    • pulse wave complete
    • successive waveform generation
    • Extended temperature option (-40 to 85°C)
  • Specs & Data Sheets

    Specs & Catalogs

    Manuals

    IP480 User Manual (Log in to download the file)

    Drawings & Diagrams

  • Software

    IPSW-API-LNX (Log in to download the file)
  • Accessories

    • Compare

      502x Cable Series

      • Communication Signal Cables
      • Wide assortment of ribbon cables
      $40$600
      Select options
    • Compare

      IPSW-API: I/O Function Routines for VxWorks, Windows, Linux

      • Use with IndustryPack modules/carriers
      • Easy installation procedure
      • Help files with step-by-step instructions
      • Demonstration Program
      • Driver level support for desktop and embedded Windows level programming environments
      $365$1,005
      Read more
    • Compare

      Termination Products

      • DIN rail-mount panels
      • 50 screw terminals on 50-pin connector termination panels
      • 50 screw terminals on SCSI-2 connector termination panels
      • 68 screw terminals on SCSI-3 connector termination panels
      $165$210
      Select options
    • Compare

      Transition Modules

      • Various transition modules
      $220$890
      Select options
  • Additional information

    Additional information

    Weight N/A
    Dimensions N/A
    Part Number

    TRANS-200: Use with AVME9670 & AVME9670E, TRANS-C100: Use with AcPC8635, TRANS-C200: Use with ACPC8625, XBRD-9060-LF: Expansion I/O Carrier Module, XVME-9640-1-LF: Transition Module with P0 connector, XVME-9640-2-LF: Transition Module without P0 connector, TRANS-C4610: Use with AcPC4610, TRANS-C4620: Use with AcPC4620E and AcPC4620CC, TRANS-C5200: Use with AcPC4620E and AcPC4620CC with 128 CMOS I/O, TRANS-C5201: Use with AcPC4620E and AcPC4620CC with 64 EIA485 I/O channels, TRANS-C5210: Use with AcPC8625, VPX4500-RTM-LF: Use with VPX4500E-LF and VPX4500-CC-LF, TRANS-V112-LF: Rear transition module for the VPX4812 / VPX4814