IP400: Digital Input Module, High Voltage Inputs
Product short description:
- 40 input channels
- 0-60V DC input range
- Change-of-state/level interrupts (up to 12 channels)
The IP400 can monitor the on/off (high/low) status of up to 40 devices.
Loopback monitoring of critical control signals is easily accomplished with the IP400 by reading the output states of Acromag’s IP405 Output Module. The two modules share the same field interface pinouts for direct loopback compatibility.
Configuration is easy with software commands that eliminate confusing jumper settings and switches. You can configure interrupts for a change of state or level detection of any bit on up to 12 channels.
Specifications
Digital Inputs
Input channel configuration: 40 noninverting buffered inputs with a common connection. For DC voltage applications only,observe proper polarity.
Input voltage: 0 to 60V DC,maximum.
Input signal threshold: TTL compatible. 1.5V DC with 200mV of hysteresis, typical. Thus, Low-to-High threshold is 1.6V DC High-to-Low is 1.4V DC, typical. Limited to TTL levels of
0.8V DC (maximum Low level) and 2.0V DC (minimum High level).
Input resistance time: 100K ohms, typical.
Interrupts: Change-of-state and level on channels 0-11.
IP Compliance (ANSI/VITA 4)
Meets IP specifications per ANSI/VITA 4-1995.
IP data transfer cycle types supported: Input/output (IOSel*), ID read (IDSel*).
Access Times (8MHz clock): 1 wait state (375nS cycle).
Interrupts: Handling format: An 8-bit vector is provided during interrupt acknowledge cycles.
Updates: Requires two 16-bit and one 8-bit reads to update all channels.
Environmental
Operating temperature: 0 to 70°C (IP400) or -40 to 85°C (IP400E model).
Storage temperature: -55 to 125°C.
Relative Humidity: 5 to 95% non-condensing
MTBF: 1,653,871 hrs at 25°C, MIL-HDBK-217F, Notice 2.
Power:
+5V (±5%): 30mA maximum.
+12V (±5%) from P1: 8.5mA maximum.
-12V (±5%) from P1: 0mA (not used).
- 40 digital inputs
- 0 to 60V DC input range
- TTL input threshold with hysteresis
- Change-of-state/level interrupts (up to 12 channels)
- Loopback monitoring of output states (with IP405)
- 0 to 70°C (IP400) or -40 to 85°C (IP400E model)
- Buffered inputs include hysteresis for increased noise immunity.
- Interrupts can be generated for change of state or level detection.
- Loopback monitoring enables self-test and fault diagnostics to detect open switches or shorts.
- High impedance inputs minimize loading of the input source and input current.
- Faster data processing is achieved because only one “wait” state is required for a read or a write operation.
Specs & Catalogs
Manuals
IP400 User Manual (Log in to download the file)
Catalogs
Drawings & Diagrams
-
502x Cable Series
- Communication Signal Cables
- Wide assortment of ribbon cables
$40 – $600Select options -
Conformal Coating
Moisture and humidity protection for boards via Acromag applied conformal coating using acrylic resin (Humiseal 1B31).$55Select options -
CS-IP Conformal Coat
Industry Pack conformal coat. This option should be selected to prevent high temperature and humidity issues (like blotching) when boards are conformal coated$75Select options -
IPSW-API: I/O Function Routines for VxWorks, Windows, Linux
- Use with IndustryPack modules/carriers
- Easy installation procedure
- Help files with step-by-step instructions
- Demonstration Program
- Driver level support for desktop and embedded Windows level programming environments
$375 – $1,005Select options -
Termination Products
- DIN rail-mount panels
- 50 screw terminals on 50-pin connector termination panels
- 50 screw terminals on SCSI-2 connector termination panels
- 68 screw terminals on SCSI-3 connector termination panels
$165 – $225Select options
Additional information
Weight | 8 oz |
---|---|
Dimensions | 4 × 2 × 1 in |
Part Number | IP400: 40 digital inputs., IP400E: 40 digital inputs, extended temp. range. |
Product Series | Industry Pack |
-
Description
The IP400 can monitor the on/off (high/low) status of up to 40 devices.
Loopback monitoring of critical control signals is easily accomplished with the IP400 by reading the output states of Acromag’s IP405 Output Module. The two modules share the same field interface pinouts for direct loopback compatibility.
Configuration is easy with software commands that eliminate confusing jumper settings and switches. You can configure interrupts for a change of state or level detection of any bit on up to 12 channels.
Specifications
Digital Inputs
Input channel configuration: 40 noninverting buffered inputs with a common connection. For DC voltage applications only,observe proper polarity.
Input voltage: 0 to 60V DC,maximum.
Input signal threshold: TTL compatible. 1.5V DC with 200mV of hysteresis, typical. Thus, Low-to-High threshold is 1.6V DC High-to-Low is 1.4V DC, typical. Limited to TTL levels of
0.8V DC (maximum Low level) and 2.0V DC (minimum High level).
Input resistance time: 100K ohms, typical.
Interrupts: Change-of-state and level on channels 0-11.IP Compliance (ANSI/VITA 4)
Meets IP specifications per ANSI/VITA 4-1995.
IP data transfer cycle types supported: Input/output (IOSel*), ID read (IDSel*).
Access Times (8MHz clock): 1 wait state (375nS cycle).
Interrupts: Handling format: An 8-bit vector is provided during interrupt acknowledge cycles.
Updates: Requires two 16-bit and one 8-bit reads to update all channels.Environmental
Operating temperature: 0 to 70°C (IP400) or -40 to 85°C (IP400E model).
Storage temperature: -55 to 125°C.
Relative Humidity: 5 to 95% non-condensing
MTBF: 1,653,871 hrs at 25°C, MIL-HDBK-217F, Notice 2.Power:
+5V (±5%): 30mA maximum.
+12V (±5%) from P1: 8.5mA maximum.
-12V (±5%) from P1: 0mA (not used). -
Features & Benefits
- 40 digital inputs
- 0 to 60V DC input range
- TTL input threshold with hysteresis
- Change-of-state/level interrupts (up to 12 channels)
- Loopback monitoring of output states (with IP405)
- 0 to 70°C (IP400) or -40 to 85°C (IP400E model)
- Buffered inputs include hysteresis for increased noise immunity.
- Interrupts can be generated for change of state or level detection.
- Loopback monitoring enables self-test and fault diagnostics to detect open switches or shorts.
- High impedance inputs minimize loading of the input source and input current.
- Faster data processing is achieved because only one “wait” state is required for a read or a write operation.
-
Specs & Data Sheets
Specs & Catalogs
Manuals
IP400 User Manual (Log in to download the file)
Catalogs
Drawings & Diagrams
-
Software
IPSW-API-LNX (Log in to download the file) -
Accessories
-
502x Cable Series
- Communication Signal Cables
- Wide assortment of ribbon cables
$40 – $600Select options -
Conformal Coating
Moisture and humidity protection for boards via Acromag applied conformal coating using acrylic resin (Humiseal 1B31).$55Select options -
CS-IP Conformal Coat
Industry Pack conformal coat. This option should be selected to prevent high temperature and humidity issues (like blotching) when boards are conformal coated$75Select options -
IPSW-API: I/O Function Routines for VxWorks, Windows, Linux
- Use with IndustryPack modules/carriers
- Easy installation procedure
- Help files with step-by-step instructions
- Demonstration Program
- Driver level support for desktop and embedded Windows level programming environments
$375 – $1,005Select options -
Termination Products
- DIN rail-mount panels
- 50 screw terminals on 50-pin connector termination panels
- 50 screw terminals on SCSI-2 connector termination panels
- 68 screw terminals on SCSI-3 connector termination panels
$165 – $225Select options
-
-
Additional information
Additional information
Weight 8 oz Dimensions 4 × 2 × 1 in Part Number IP400: 40 digital inputs., IP400E: 40 digital inputs, extended temp. range.
Product Series Industry Pack
Please login to submit this form.