Click to zoom
$1,295$1,995
Clear
Product short description:
  • Holds one PMC/XMC module
  • PMC rear I/O
  • PCIe bus 8-lane Gen 1 or 2 interface backplane connection
  • Air-cooled, conduction-cooled, REDI versions
RSS
FACEBOOK
FACEBOOK
TWITTER
Visit Us
LINKEDIN

These 3U mezzanine carrier cards provide a simple and cost-effective solution for interfacing a PMC or XMC module to a VPX computer system. The carrier card routes power and bus signals to a plug-in mezzanine module through the VPX card slot connector. Industrial I/O and configurable FPGA modules from Acromag or other vendors are supported.

Compatible VITA 65 module / slot profiles:
MOD3-PER-1F-16.3.2-2 / SLT3-PER-1F-14.3.2
MOD3-PAY-1D-16.2.6-11 / SLT3-PAY-1D-14.2.6

These carriers are ideal for high-performance industrial, defense, scientific research, and telephony systems requiring high-speed I/O expansion. The VPX4810-LF is available in three versions: air-cooled, conduction-cooled and a Ruggedized Enhanced Design Implementation (REDI VITA 48).

Performance Specifications

General

Form Factor: 3U VPX bus 6.299” (160mm) x 3.937” (100.0mm).
Pitch
VPX4810 (air-cooled): 1.0” pitch
VPX4810-CC (conduction-cooled): 0.85” pitch
VPX4810-REDI (conduction-cooled REDI): 1.00” pitch
Front Panel: The VPX4810-LF has a 1.0” VITA 48.1 front panel. Contact the factory for IEEE 1101.10 1.0” and 0.8” options.
VPX Carrier Interface: Compatible VITA 65 module / slot profiles: MOD3-PER-1F-16.3.2-2 / SLT3-PER-1F-14.3.2, MOD3-PAY-1D-16.2.6-11 / SLT3-PAY-1D-14.2.6
Note 1: Board is compatible with payload profiles but has no hosting capabilities.
FRU EEPROM with temperature monitor.
PMC/XMC Interface: One IEEE 1386.1 PMC/XMC module in single VPX slot. PMC site is PCI 3.0 compliant, 32/64-bit, 33/66MHz. PMC site is PCI-X 1.0b compliant, 64-bit, 66/100/133MHz. XMC site is PCIe Gen. 2.0 and 8 lanes wide. 3.3V, 5V and ±12V provided for PMC modules via the VPX backplane.
Front or rear panel I/O support for the PMC site with 64 I/O lines, or 32 differential pairs. Rear I/O is compliant to VITA 46.9 P2w1-P64s.

Power Requirements

Carrier-Only Power Requirements
+3.3V DC: 0.9A typical plus any additional power consumed by PMC/XMC.
+5V DC: 0.9A typical plus any additional power consumed by PMC and XMC (VPWR).
+12V DC and –12V DC provided to PMC and XMC site (aux only).

Environmental

Air-Cooled Operating Temperature: 0 to 70°C (air flow requirement as measured to be greater than 200 LFM).
Conduction-Cooled Operating Temperature Range: -40 to 85°C (board must operate in a fully-installed conduction-cooled rack).
REDI (VITA 48) Operating Temperature Range: -40 to 85°C (board MUST operate in a fully-installed conduction-cooled, REDI supported rack).
Storage Temperature Range: -55 to 100°C.
Relative Humidity: 5 to 95% non-condensing.
MTBF: 2,652,569 hrs. at 25°C. , 1,672,742 hrs. at 40°C.
Vibration: 0.05g RMS (20 – 2000Hz) random, operating 6g RMS per Hz spectrum.
Shock: 30g each axis, 11ms.

  • Half-length PCI card
  • 3U VPX carrier board delivers 25W of power to one PMC/XMC site
  • PMC/XMC site uses 64-bit, 66/133MHz PLX technology with a PCIe to PCI-X bridge
  • PCIe bus 8-lane Gen 1 or 2 interface backplane connection
  • Supports standard PMC/XMC modules (IEEE 1386.1)
  • Conforms to VPX VITA 46.0, 46.4 and 46.9 specifications and optionally VITA 48
  • Supports front or rear panel PMC/XMC I/O
  • Supports 64 I/O lines (P14, VITA 46.9) via the P2 VPX connector
  • 3.3V PCI-X signaling PMC site
  • +12V and –12V provided to PMC/XMC site
  • Monitors FRU information and module temperature

Manuals

VPX4810 User Manual (Log in to download the file)

Will Acromag's VPX4810 work in my System? (Log in to download the file)

Drawings & Diagrams

Additional information

Weight 16 oz
Dimensions 7 × 4 × 1 in
Part Number

VPX4810-CC-LF: Conduction-cooled, VPX4810-LF: Air-cooled, VPX4810-REDI-LF: REDI VITA 48

  • Description

    These 3U mezzanine carrier cards provide a simple and cost-effective solution for interfacing a PMC or XMC module to a VPX computer system. The carrier card routes power and bus signals to a plug-in mezzanine module through the VPX card slot connector. Industrial I/O and configurable FPGA modules from Acromag or other vendors are supported.

    Compatible VITA 65 module / slot profiles:
    MOD3-PER-1F-16.3.2-2 / SLT3-PER-1F-14.3.2
    MOD3-PAY-1D-16.2.6-11 / SLT3-PAY-1D-14.2.6

    These carriers are ideal for high-performance industrial, defense, scientific research, and telephony systems requiring high-speed I/O expansion. The VPX4810-LF is available in three versions: air-cooled, conduction-cooled and a Ruggedized Enhanced Design Implementation (REDI VITA 48).

    Performance Specifications

    General

    Form Factor: 3U VPX bus 6.299” (160mm) x 3.937” (100.0mm).
    Pitch
    VPX4810 (air-cooled): 1.0” pitch
    VPX4810-CC (conduction-cooled): 0.85” pitch
    VPX4810-REDI (conduction-cooled REDI): 1.00” pitch
    Front Panel: The VPX4810-LF has a 1.0” VITA 48.1 front panel. Contact the factory for IEEE 1101.10 1.0” and 0.8” options.
    VPX Carrier Interface: Compatible VITA 65 module / slot profiles: MOD3-PER-1F-16.3.2-2 / SLT3-PER-1F-14.3.2, MOD3-PAY-1D-16.2.6-11 / SLT3-PAY-1D-14.2.6
    Note 1: Board is compatible with payload profiles but has no hosting capabilities.
    FRU EEPROM with temperature monitor.
    PMC/XMC Interface: One IEEE 1386.1 PMC/XMC module in single VPX slot. PMC site is PCI 3.0 compliant, 32/64-bit, 33/66MHz. PMC site is PCI-X 1.0b compliant, 64-bit, 66/100/133MHz. XMC site is PCIe Gen. 2.0 and 8 lanes wide. 3.3V, 5V and ±12V provided for PMC modules via the VPX backplane.
    Front or rear panel I/O support for the PMC site with 64 I/O lines, or 32 differential pairs. Rear I/O is compliant to VITA 46.9 P2w1-P64s.

    Power Requirements

    Carrier-Only Power Requirements
    +3.3V DC: 0.9A typical plus any additional power consumed by PMC/XMC.
    +5V DC: 0.9A typical plus any additional power consumed by PMC and XMC (VPWR).
    +12V DC and –12V DC provided to PMC and XMC site (aux only).

    Environmental

    Air-Cooled Operating Temperature: 0 to 70°C (air flow requirement as measured to be greater than 200 LFM).
    Conduction-Cooled Operating Temperature Range: -40 to 85°C (board must operate in a fully-installed conduction-cooled rack).
    REDI (VITA 48) Operating Temperature Range: -40 to 85°C (board MUST operate in a fully-installed conduction-cooled, REDI supported rack).
    Storage Temperature Range: -55 to 100°C.
    Relative Humidity: 5 to 95% non-condensing.
    MTBF: 2,652,569 hrs. at 25°C. , 1,672,742 hrs. at 40°C.
    Vibration: 0.05g RMS (20 – 2000Hz) random, operating 6g RMS per Hz spectrum.
    Shock: 30g each axis, 11ms.

  • Features & Benefits

    • Half-length PCI card
    • 3U VPX carrier board delivers 25W of power to one PMC/XMC site
    • PMC/XMC site uses 64-bit, 66/133MHz PLX technology with a PCIe to PCI-X bridge
    • PCIe bus 8-lane Gen 1 or 2 interface backplane connection
    • Supports standard PMC/XMC modules (IEEE 1386.1)
    • Conforms to VPX VITA 46.0, 46.4 and 46.9 specifications and optionally VITA 48
    • Supports front or rear panel PMC/XMC I/O
    • Supports 64 I/O lines (P14, VITA 46.9) via the P2 VPX connector
    • 3.3V PCI-X signaling PMC site
    • +12V and –12V provided to PMC/XMC site
    • Monitors FRU information and module temperature
  • Specs & Data Sheets

    Manuals

    VPX4810 User Manual (Log in to download the file)

    Will Acromag's VPX4810 work in my System? (Log in to download the file)

    Drawings & Diagrams

  • Additional information

    Additional information

    Weight 16 oz
    Dimensions 7 × 4 × 1 in
    Part Number

    VPX4810-CC-LF: Conduction-cooled, VPX4810-LF: Air-cooled, VPX4810-REDI-LF: REDI VITA 48