Click to zoom
$700
Clear
Product short description:
  • 8-lane PCI Express interface
  • Holds one XMC module
RSS
FACEBOOK
FACEBOOK
TWITTER
Visit Us
LINKEDIN

Acromag’s APCe8675 carrier card interfaces an XMC mezzanine module to a PCI Express bus in a PC-based desktop computer system.

The APCe8675 is a PCIe bus adapter board that allows a PC (PCIe bus master) to control and communicate with the hosted XMC module. It simply acts as an adapter to route signals between the system’s PCIe bus and the XMC module connector.

This card is a Peripheral Component Interconnect Express (PCIe) bus card carrier for an XMC module. The carrier card acts as an adapter to route PCIe bus signals between the PCIe bus of your PC and the P15 connector of an XMC module card. Access to XMC P16 and P4 rear I/O is provided through connectors P2, P3 and J1. XMC modules with front I/O can be accessed though the front mounting bracket. Cables are available to connect the P2 and P3 rear I/O signals to other carrier cards in adjacent slots. Cables are also available to connect the J1 rear I/O to a front panel bracket mounted connector located in an adjacent slot.

The I/O signals are accessible via rear connectors and though the front mounting bracket. To simplify wiring, Acromag offers cables to connect the carrier’s rear I/O signals to other carrier cards in adjacent slots. Cables are also available to connect the carrier’s rear I/O to a front panel connector in an adjacent slot.

Select XMC modules from Acromag’s offering of high-performance FPGA and I/O solutions or use any third-party ANSI/VITA 42 compliant mezzanine modules.

Performance Specifications

XMC Compliance

XMC Module: Complies with ANSI/VITA 42.0-2008.

I/O Interface

Serial Rear I/O (P2, P3): Connector: Samtec QSH-DP 0.50 mm Q Pairs® high speed ground plane socket strip, differential pair.
These ports provide the ability to connect to left and right neighbor carrier cards using high speed serial protocols such as XAUI or Aurora.
Supports up to five transmit and five receive high speed (5Gb/s) differential pairs or five LVDS pairs when used with Samtec QPairs® High Speed Twinax cables.
Rear I/O (J1): Connector: MD68 (internal SCSI), male.32 LVDS pairs routed from the XMC P4 connector.

PCI Express Interface

PCI Express interface: 8 lane, Gen 1 capable.
PCIe bus compliance: This device meets or exceeds all written PCI Express specifications per revision 1.1 dated March 28, 2005.

Environmental

Operating temperature: 0 to 70°C.
Storage temperature: -55 to 125°C.
Relative humidity: 5 to 95% non-condensing.
Power: The carrier provides 3.3V, 12V and -12V power to the XMC module. The 12V power source is jumperselectable from the PCIe bus 12V supply or the PCIe graphics power connector. The DC/DC converter generates a -12V supply from the 12V source. 3.3V (±10%): 0mA. 12V (±5%): 270mA, typical with fan operating.
Currents specified are for the carrier board only. For the total current required from each supply, add the XMC module currents.
MTBF: Contact the factory.

Physical

Dimensions: Length: 12.283 inches (312.0 mm). Height: 4.200 inches (106.68 mm).
Width: Occupies two slots with fan installed (fan is mounted on solder side, height is 10 mm). Occupies one slot with fan removed.
Board thickness: 0.062 inches (1.59 mm).
Connectors
J1: Board-to-board connection of J14 user signals.
J2: Power source select jumper.
J3: Auxiliary power connector (PCIe graphics).
J4: JTAG I/O voltage select jumper.
J14, J16 : XMC user signals (rear I/O).
J15: XMC PCIe signals.
P1: PCI Express V1.1 x8 lanes card edge.
P2, P3: Board-to-board connection of J16 user signals.
P4: Fan power.
P5: JTAG (Xilinx programming adapter).

Approvals

CE marked, FCC Part 15, Class A

  • One XMC module slot
  • 8-lane PCI Express interface
  • Cooling fan
  • Supports high-speed serial interface between neighboring cards using protocols such as XAUI or Aurora
  • Routes 32 differential pairs to rear connector for LVDS I/O from the XMC module
  • JTAG programming connector supports Xilinx programmer for use in with hosted FPGA modules
  • Auxilliary power connection for 12V source

Manuals

APCe8675 User Manual (Log in to download the file)

Drawings & Diagrams

Additional information

Weight 16 oz
Dimensions 10 × 2 × 2 in
Part Number

5025-550x: 50-pin female to 50-pin female cable, 12 ft max., 5025-550-4: 50-pin female to 50-pin female cable, 4 ft., 5025-550-7: 5025-550-4: 50-pin female to 50-pin female cable, 7 ft, 5025-550-10: 5025-550-4: 50-pin female to 50-pin female cable, 10 ft, 5028-372: SCSI-2 to CHAMP 0.8mm, 5028-420: VHDCI 68-pin to SCSI-3 MD68, 5028-609: 68-pin VHDCI to four male DSUB-9 connectors, 5028-615: 68-pin CHAMP to pigtail, 36", 5028-616: 68-pin CHAMP to pigtail, 70", 5028-619: 50-pin CHAMP to pigtail, 36", 5028-620: 50-pin CHAMP to pigtail, 70", 5028-568: RJ Point 5 Male to RJ45 Female, 5028-572: 26-pin to 2 USB, VGA, Serial, 5028-187: Shielded, SCSI-2 to flat 50-pin connector, 5028-432: SCSI-3 68-pin connectors at both ends, 5028-438: SCSI-2 50-pin connector at both ends, 5028-449: SFP-to-SFP (male-male) connectors, 5028-564: development cable for VPX4812, 5025-913: SCSI cable with PCI bracket-mounted HD68 female connector, 5025-917: high speed twinax cable for board-to-board connections, 5025-921: VHDCI 36-pin to SCSI-2, 5028-570: SCSI II connectors, for IP571/IP572 when installed on AVME9668, 5028-617: Audio cable, 5028-618: Serial COM cable, 5028-628: ACEX4041 Cable shutdown

  • Description

    Communication Signal Cables

    Acromag provides a large selection of signal cables to complete the connection of the field wiring on the termination panel to the I/O board. We offer you a wide assortment of ribbon cables to accommodate the various pin and connector configurations.

    5028-420: Round cable, shielded, male SCSI-3 connecor to 68-pin CHAMP 0.8mm, 2 meters long.

    5028-432: Round cable, shielded, 6 ft. long, SCSI-3 68-pin connectors at both ends.

    5028-438: Round cable, shielded, 6 ft. long, SCSI-2 50-pin connector at both ends.

    5028-564: VPX4812 6″ JTAG development cable.

    5028-615: Cable, 68-pin CHAMP to pigtail, 36 inches long.

    5028-616: Cable, 68-pin CHAMP to pigtail, 70 inches long.

    5028-617: Audio cable.

    5028-618: Serial COM cable.

    5028-629: ACEX4041 Cable shutdown

    5025-913: CS Electronics internal SCSI cable with PCI bracket-mounted HD68 female connector. Brings the XMC J14 rear I/O signals to back panel of the PC. Use with APCe8670 and APCe8675 carrier cards.

    5025-917: Samtec Q Pairs® high speed twinax cable for board-to-board connections. 3 inches long, 20 differential pairs. Connects carrier cards in adjacent slots between P2 or P3 connectors. High-speed serial signals originate from XMC J16 rear I/O. Use with APCe8675 carrier card.

    5025-921: Cable: VHDCI 36-pin to SCSI-2, 6 feet. Use with XMC-6VLX240F and XMC-6VLX365F.

  • Features & Benefits

    • One XMC module slot
    • 8-lane PCI Express interface
    • Cooling fan
    • Supports high-speed serial interface between neighboring cards using protocols such as XAUI or Aurora
    • Routes 32 differential pairs to rear connector for LVDS I/O from the XMC module
    • JTAG programming connector supports Xilinx programmer for use in with hosted FPGA modules
    • Auxilliary power connection for 12V source
  • Specs & Data Sheets

    Manuals

    APCe8675 User Manual (Log in to download the file)

    Drawings & Diagrams

  • Accessories

  • Additional information

    Additional information

    Weight 16 oz
    Dimensions 10 × 2 × 2 in
    Part Number

    5025-550x: 50-pin female to 50-pin female cable, 12 ft max., 5025-550-4: 50-pin female to 50-pin female cable, 4 ft., 5025-550-7: 5025-550-4: 50-pin female to 50-pin female cable, 7 ft, 5025-550-10: 5025-550-4: 50-pin female to 50-pin female cable, 10 ft, 5028-372: SCSI-2 to CHAMP 0.8mm, 5028-420: VHDCI 68-pin to SCSI-3 MD68, 5028-609: 68-pin VHDCI to four male DSUB-9 connectors, 5028-615: 68-pin CHAMP to pigtail, 36", 5028-616: 68-pin CHAMP to pigtail, 70", 5028-619: 50-pin CHAMP to pigtail, 36", 5028-620: 50-pin CHAMP to pigtail, 70", 5028-568: RJ Point 5 Male to RJ45 Female, 5028-572: 26-pin to 2 USB, VGA, Serial, 5028-187: Shielded, SCSI-2 to flat 50-pin connector, 5028-432: SCSI-3 68-pin connectors at both ends, 5028-438: SCSI-2 50-pin connector at both ends, 5028-449: SFP-to-SFP (male-male) connectors, 5028-564: development cable for VPX4812, 5025-913: SCSI cable with PCI bracket-mounted HD68 female connector, 5025-917: high speed twinax cable for board-to-board connections, 5025-921: VHDCI 36-pin to SCSI-2, 5028-570: SCSI II connectors, for IP571/IP572 when installed on AVME9668, 5028-617: Audio cable, 5028-618: Serial COM cable, 5028-628: ACEX4041 Cable shutdown