Click to zoom
$780$900
Clear
Product short description:
  • Two IP module slots
  • Rear access I/O
  • Plug-and-play carrier configuration and interrupt support
RSS
FACEBOOK
FACEBOOK
TWITTER
Visit Us
LINKEDIN

The AcPC8635A is a non-intelligent slave board that interfaces two IP modules to the CompactPCI® (cPCI) bus.

All 100 I/O points are brought out the rear J2 connector. This convenience eliminates messy cables from hanging out the front of the cage. In addition to a more efficient cage wiring design, it is also much easier to insert and replace boards.

Performance Specifications

General

Acromag’s carrier boards provide full data access to the IP module’s I/O, ID and interrupt spaces. With full access to the programmable registers, you can easily configure and control the operation of the IP modules from the cPCI bus.

Up to two interrupt requests are supported for each IP module. All board interrupts are mapped to PCI bus INTA# signal.

Individual passive filters on each IP power supply line provide optimum filtering and noise isolation between the IP modules and the carrier board.

IP Compliance (ANSI/VITA 4)

Meets IP specs per ANSI/VITA 4-1995 (8MHz operation only) and IP I/O mapping to J2 per PICMG 2.4 R1.0.
Electrical/mechanical interface: Supports single or double size IP modules.
IP Module I/O space, ID space, INT, and MEM space supported.
Interrupts: Supports two interrupt requests per IP module and interrupt acknowledge cycles via access to IP INT space.

CompactPCI bus Compliance

Meets PCI spec. V2.1 and PICMG 2.0, R2.1.
Data transfer bus: Slave with 32-bit, 16-bit, and 8-bit data transfer operation. 32-bit read/write accesses are implemented as two 16-bit transfers to the IPs.
Interrupts: CompactPCI bus INTA# interrupt signal. Up to two requests sourced from each IP mapped to INTA#. Interrupts come from IP modules via access to IP module INT space.
32-bit memory space: Upon power-up, the system auto-configuration process (plug & play) maps the carrier’s base address (for a 1K byte block of memory) into the PCI bus 32-bit memory space.

Power Requirements

Power
3.3V (±5%): 300mA maximum.
5V (±5%): 30mA maximum.
±12V (±5%): 0mA (not used).
Plus IP module load.
MTBF: Contact factory

Environmental

Operating temperature: 0 to 70°C (AcPC8635A model) or -40 to 85°C (AcPC8635AE model).
Storage temperature: -55 to 100°C.
Relative humidity: 5 to 95% non-condensing.

  • Two industry-standard IP module slots
  • Board resides in memory space
  • Supports IP module I/O, ID, INT, and MEM spaces
  • Supports 8 and 32 MHz operation
  • 100 I/O points with rear access
  • High-density rear connectors
  • Compatible with 32-bit CompactPCI® backplane
  • Plug-and-play carrier configuration and interrupt support
  • Two interrupt channels per IP module
  • Front panel LEDs
  • Supervisory circuit for reset generation
  • Individually filtered and fused power to each IP
  • • Ruggedized with ESD strip and EMC front panel
  • • Easily integrate IPs with your software using RTOS VxWorks, Linux, or Win DLL for Windows® 2000/XP/Vista/7 32-bit systems
  • Compare

    502x Cable Series

    • Communication Signal Cables
    • Wide assortment of ribbon cables
    $75$600
    Select options
  • Compare

    Termination Products

    • DIN rail-mount panels
    • 50 screw terminals on 50-pin connector termination panels
    • 50 screw terminals on SCSI-2 connector termination panels
    • 68 screw terminals on SCSI-3 connector termination panels
    $165$210
    Select options
  • Compare

    Transition Modules

    • Various transition modules
    $220$890
    Select options

Additional information

Weight N/A
Dimensions N/A
Part Number

TRANS-200: Use with AVME9670 & AVME9670E, TRANS-C100: Use with AcPC8635, TRANS-C200: Use with ACPC8625, XBRD-9060-LF: Expansion I/O Carrier Module, XVME-9640-1-LF: Transition Module with P0 connector, XVME-9640-2-LF: Transition Module without P0 connector, TRANS-C4610: Use with AcPC4610, TRANS-C4620: Use with AcPC4620E and AcPC4620CC, TRANS-C5200: Use with AcPC4620E and AcPC4620CC with 128 CMOS I/O, TRANS-C5201: Use with AcPC4620E and AcPC4620CC with 64 EIA485 I/O channels, TRANS-C5210: Use with AcPC8625, VPX4500-RTM-LF: Use with VPX4500E-LF and VPX4500-CC-LF, TRANS-V112-LF: Rear transition module for the VPX4812 / VPX4814

  • Description

    These adapters repeat field I/O connections on Acromag’s carrier cards for front or rear exit from the card cage.

    Transition modules provide a solution for controlling the location of your cabling within the card cage.

    TRANS-200: Transition module
    Transition module for AVME9670 board. See AVME9670 manual for more information.

    VPX4500-RTM-LF: Rear transition module used with both the VPX4500E-LF and the VPX4500-CC-LF carriers to provide access to the slot C AcroPack field I/O signals. See carrier card user manual for more information

     

     

  • Features & Benefits

    • Two industry-standard IP module slots
    • Board resides in memory space
    • Supports IP module I/O, ID, INT, and MEM spaces
    • Supports 8 and 32 MHz operation
    • 100 I/O points with rear access
    • High-density rear connectors
    • Compatible with 32-bit CompactPCI® backplane
    • Plug-and-play carrier configuration and interrupt support
    • Two interrupt channels per IP module
    • Front panel LEDs
    • Supervisory circuit for reset generation
    • Individually filtered and fused power to each IP
    • • Ruggedized with ESD strip and EMC front panel
    • • Easily integrate IPs with your software using RTOS VxWorks, Linux, or Win DLL for Windows® 2000/XP/Vista/7 32-bit systems
  • Specs & Data Sheets

  • Accessories

    • Compare

      502x Cable Series

      • Communication Signal Cables
      • Wide assortment of ribbon cables
      $75$600
      Select options
    • Compare

      Termination Products

      • DIN rail-mount panels
      • 50 screw terminals on 50-pin connector termination panels
      • 50 screw terminals on SCSI-2 connector termination panels
      • 68 screw terminals on SCSI-3 connector termination panels
      $165$210
      Select options
    • Compare

      Transition Modules

      • Various transition modules
      $220$890
      Select options
  • Additional information

    Additional information

    Weight N/A
    Dimensions N/A
    Part Number

    TRANS-200: Use with AVME9670 & AVME9670E, TRANS-C100: Use with AcPC8635, TRANS-C200: Use with ACPC8625, XBRD-9060-LF: Expansion I/O Carrier Module, XVME-9640-1-LF: Transition Module with P0 connector, XVME-9640-2-LF: Transition Module without P0 connector, TRANS-C4610: Use with AcPC4610, TRANS-C4620: Use with AcPC4620E and AcPC4620CC, TRANS-C5200: Use with AcPC4620E and AcPC4620CC with 128 CMOS I/O, TRANS-C5201: Use with AcPC4620E and AcPC4620CC with 64 EIA485 I/O channels, TRANS-C5210: Use with AcPC8625, VPX4500-RTM-LF: Use with VPX4500E-LF and VPX4500-CC-LF, TRANS-V112-LF: Rear transition module for the VPX4812 / VPX4814