Click to zoom
$2,050
Clear
Product short description:
  • Two PMC module slots
  • Front or rear access I/O
  • Plug-and-play carrier configuration and interrupt support

This board provides an easy and low cost solution that enables use of a PMC mezzanine I/O module in a standard 6U CompactPCI computer system. The carrier card acts simply as an adapter to route PCI bus signals to and from the PMC module through the CompactPCI card slot edge connector. All Acromag PMC modules and those from other vendors are supported.

RSS
FACEBOOK
FACEBOOK
TWITTER
Visit Us
LINKEDIN

This board uses a PLX Technology PCI6540 transparent PCI/PCI bridge for data transactions from the PCI bus (system host) to two PMC sites. The bridge device provides a 32 or 64-bit PCI interface with 33 or 66MHz bus frequencies.

A heat frame enables conduction cooling in applications where ambient or forced air can’t provide adequate cooling. This unit is ideal for airborne systems, deployment in battleground equipment, and other situations with advanced thermal management requirements. Field I/O signals are routed through the carrier card’s rear J3 and J5 connectors.

An air-cooled rear transition board, Acromag Model TRANS-C4620, maps the field I/O on the PMC module to the rear of the CompactPCI system.

Specifications

Environmental

Operating temperature: -40 to 85°C (conduction-cooled.)

Storage temperature: -55 to 100°C.

Relative humidity: 5-95% non-condensing

American National Standard for 2mm Connector Equipment

Practice on Conduction Cooled Euroboards: ANSI/VITA 30.1-2002.

American National Standard for Conduction Cooled PMC: ANSI/VITA 20-2001(R2005).

Power (received from the CompactPCI 3U Back Plane):
3.3V DC (±5%)*: 135mA typical, 150mA max.
5.0V DC (±5%)*: 50mA typical, 70mA max.
±12V DC (±5%)**: Per PMC module.
* With no PMC module installed, ±12V DC not used.
** Max. power 7.5W (total all supplies) per PMC standard.

MTBF: Call factory

Physical: CompactPCI Carrier Cards

Physical configuration: 6U CompactPCI Card 233.35 x 160mm.

Rear CompactPCI connectors: 2mm J1, J2, J3, J5 connectors.

PMC connectors: Eight 1mm connectors.

The conduction-cooled model (AcPC4620CC) uses a conduction-cooled frame with wedge-loks® and thermo bars.

Physical: Transition Module

Physical configuration: Half-length 6U CompactPCI Card 233.35 x 80mm.

Connectors: 2mm RJ2 connector which maps the rear I/O signals to a SCSI-3 connector. This model also uses a standard rear front panel assembly with a SCSI-3 connector cutout.

PMC and CompactPCI bus Compliance

Meets PCI specification version 2.3, CompactPCI specification PICMG 2.3 R1.0, and PMC specification P1386.1.

Meets PCI specification version 2.3, CompactPCI specification PICMG 2.3 R1.0, and PMC specification P1386.1.

Data transfer bus: Slave with 32-bit, 16-bit, and 8-bit data transfer operation.

Interrupts: CompactPCI bus INTA# interrupt signal.

PCI Interface: PLX Technology PCI6540 transparent PCI/PCI bridge for data transactions from the PCI bus (system host) to the PMC site. The bridge device provides a 32-bit 33/66 MHz PCI interface.

  • 6U CompactPCI card
  • Holds two PMC cards
  • 32 or 64-bit PCI Interface at 33 or 66 MHz
  • Transparent PCI/PCI bridge for data transactions from the PCI bus to PMC module
  • Rear connection I/O access
  • Supports both 5V and 3.3V signaling
  • Conduction-cooled -40 to 85°C

Manuals

AcPC4620CC User Manual (Includes TRANS-C4620 specifications) (Log in to download the file)

Additional information

Weight N/A
Dimensions N/A
Part Number

AcPC4620CC: CompactPCI bus carrier card

Communication
Configuration
FPGA Type
Logic Cells
Power
Product Series
  • Description

    This board uses a PLX Technology PCI6540 transparent PCI/PCI bridge for data transactions from the PCI bus (system host) to two PMC sites. The bridge device provides a 32 or 64-bit PCI interface with 33 or 66MHz bus frequencies.

    A heat frame enables conduction cooling in applications where ambient or forced air can’t provide adequate cooling. This unit is ideal for airborne systems, deployment in battleground equipment, and other situations with advanced thermal management requirements. Field I/O signals are routed through the carrier card’s rear J3 and J5 connectors.

    An air-cooled rear transition board, Acromag Model TRANS-C4620, maps the field I/O on the PMC module to the rear of the CompactPCI system.

    Specifications

    Environmental

    Operating temperature: -40 to 85°C (conduction-cooled.)

    Storage temperature: -55 to 100°C.

    Relative humidity: 5-95% non-condensing

    American National Standard for 2mm Connector Equipment

    Practice on Conduction Cooled Euroboards: ANSI/VITA 30.1-2002.

    American National Standard for Conduction Cooled PMC: ANSI/VITA 20-2001(R2005).

    Power (received from the CompactPCI 3U Back Plane):
    3.3V DC (±5%)*: 135mA typical, 150mA max.
    5.0V DC (±5%)*: 50mA typical, 70mA max.
    ±12V DC (±5%)**: Per PMC module.
    * With no PMC module installed, ±12V DC not used.
    ** Max. power 7.5W (total all supplies) per PMC standard.

    MTBF: Call factory

    Physical: CompactPCI Carrier Cards

    Physical configuration: 6U CompactPCI Card 233.35 x 160mm.

    Rear CompactPCI connectors: 2mm J1, J2, J3, J5 connectors.

    PMC connectors: Eight 1mm connectors.

    The conduction-cooled model (AcPC4620CC) uses a conduction-cooled frame with wedge-loks® and thermo bars.

    Physical: Transition Module

    Physical configuration: Half-length 6U CompactPCI Card 233.35 x 80mm.

    Connectors: 2mm RJ2 connector which maps the rear I/O signals to a SCSI-3 connector. This model also uses a standard rear front panel assembly with a SCSI-3 connector cutout.

    PMC and CompactPCI bus Compliance

    Meets PCI specification version 2.3, CompactPCI specification PICMG 2.3 R1.0, and PMC specification P1386.1.

    Meets PCI specification version 2.3, CompactPCI specification PICMG 2.3 R1.0, and PMC specification P1386.1.

    Data transfer bus: Slave with 32-bit, 16-bit, and 8-bit data transfer operation.

    Interrupts: CompactPCI bus INTA# interrupt signal.

    PCI Interface: PLX Technology PCI6540 transparent PCI/PCI bridge for data transactions from the PCI bus (system host) to the PMC site. The bridge device provides a 32-bit 33/66 MHz PCI interface.

  • Features & Benefits

    • 6U CompactPCI card
    • Holds two PMC cards
    • 32 or 64-bit PCI Interface at 33 or 66 MHz
    • Transparent PCI/PCI bridge for data transactions from the PCI bus to PMC module
    • Rear connection I/O access
    • Supports both 5V and 3.3V signaling
    • Conduction-cooled -40 to 85°C
  • Specs & Data Sheets

    Manuals

    AcPC4620CC User Manual (Includes TRANS-C4620 specifications) (Log in to download the file)

  • Additional information

    Additional information

    Weight N/A
    Dimensions N/A
    Part Number

    AcPC4620CC: CompactPCI bus carrier card

    Communication
    Configuration
    FPGA Type
    Logic Cells
    Power
    Product Series