AcPC4610E: Non-intelligent 3U cPCI PMC Carrier, Air-cooled
Product short description:
- One PMC module slot
- Front or rear access I/O
- Plug-and-play carrier configuration and interrupt support
This board provides an easy and low cost solution that enables use of a PMC mezzanine I/O module in a standard 3U CompactPCI computer system. The carrier card acts simply as an adapter to route PCI bus signals to and from the PMC module through the CompactPCI card slot edge connector. All Acromag PMC modules and those from other vendors are supported.
This board uses a PLX Technology PCI6540 transparent PCI/PCI bridge for data transactions from the PCI bus (system host) to the PMC site. The bridge device provides a 32-bit 33/66 MHz PCI interface.
Front and rear-panel access to field I/O signals are accommodated. The carrier card’s front panel cut-out provides access to a PMC module’s front I/O connector. Alternatively, all I/O signals can be routed through the carrier card’s rear J2 connector.
An air-cooled rear transition board, Acromag Model TRANS-C4610, maps the field I/O on the PMC module to the rear of the CompactPCI system.
Specifications
Environmental
Operating temperature: -40 to 85°C.
Storage temperature: -55 to 100°C.
Relative humidity: 5-95% non-condensing
Power (received from the CompactPCI 3U Back Plane):
3.3V DC (±5%)*: 135mA typical, 150mA max.
5.0V DC (±5%)*: 50mA typical, 70mA max.
±12V DC (±5%)**: Per PMC module.
* With no PMC module installed, ±12V DC not used.
** Max. power 7.5W (total all supplies) per PMC standard.
MTBF: Call factory
Physical: CompactPCI Carrier Card
Physical configuration: 3U CompactPCI Card 100 x 160mm.
Rear CompactPCI connectors: 2mm J1 & J2 connectors.
PMC connectors: Three 1mm connectors.
The air-cooled model (AcPC4610E) uses the standard front panel assembly with a PMC bezel cutout.
Physical: Transition Module
Physical configuration: Half-length 3U CompactPCI Card 100 x 80mm.
Connectors: 2mm RJ2 connector which maps the rear I/O signals to a SCSI-3 connector. This model also uses a standard rear front panel assembly with a SCSI-3 connector cutout.
PMC and CompactPCI bus Compliance
Meets PCI specification version 2.3, CompactPCI specification PICMG 2.3 R1.0, and PMC specification P1386.1.
Data transfer bus: Slave with 32-bit, 16-bit, and 8-bit data transfer operation.
Interrupts: CompactPCI bus INTA# interrupt signal.
PCI Interface: PLX Technology PCI6540 transparent PCI/PCI bridge for data transactions from the PCI bus (system host) to the PMC site. The bridge device provides a 32-bit 33/66 MHz PCI interface.
- 3U CompactPCI card
- Holds one PMC card
- 32-bit 33/66 MHz PCI Interface
- Transparent PCI/PCI bridge for data transactions from the PCI bus to PMC module
- Rear connection I/O access
- Supports both 5V and 3.3V signaling
- -40 to 85°C
Specs & Catalogs
Manuals
AcPC4610E User Manual (Includes TRANS-C4610 & TRANS-C5210 specifications and Certificate of Volatility) (Log in to download the file)
Catalogs
Drawings & Diagrams
-
502x Cable Series
- Communication Signal Cables
- Wide assortment of ribbon cables
$40 – $600Select options -
Termination Products
- DIN rail-mount panels
- 50 screw terminals on 50-pin connector termination panels
- 50 screw terminals on SCSI-2 connector termination panels
- 68 screw terminals on SCSI-3 connector termination panels
$165 – $225Select options
Additional information
Weight | N/A |
---|---|
Dimensions | N/A |
Part Number | AcPC4610E: CompactPCI bus carrier card. |
-
Description
This board provides an easy and low cost solution that enables use of a PMC mezzanine I/O module in a standard 3U CompactPCI computer system. The carrier card acts simply as an adapter to route PCI bus signals to and from the PMC module through the CompactPCI card slot edge connector. All Acromag PMC modules and those from other vendors are supported.
This board uses a PLX Technology PCI6540 transparent PCI/PCI bridge for data transactions from the PCI bus (system host) to the PMC site. The bridge device provides a 32-bit 33/66 MHz PCI interface.
Front and rear-panel access to field I/O signals are accommodated. The carrier card’s front panel cut-out provides access to a PMC module’s front I/O connector. Alternatively, all I/O signals can be routed through the carrier card’s rear J2 connector.
An air-cooled rear transition board, Acromag Model TRANS-C4610, maps the field I/O on the PMC module to the rear of the CompactPCI system.
Specifications
Environmental
Operating temperature: -40 to 85°C.
Storage temperature: -55 to 100°C.
Relative humidity: 5-95% non-condensing
Power (received from the CompactPCI 3U Back Plane):
3.3V DC (±5%)*: 135mA typical, 150mA max.
5.0V DC (±5%)*: 50mA typical, 70mA max.
±12V DC (±5%)**: Per PMC module.
* With no PMC module installed, ±12V DC not used.
** Max. power 7.5W (total all supplies) per PMC standard.
MTBF: Call factoryPhysical: CompactPCI Carrier Card
Physical configuration: 3U CompactPCI Card 100 x 160mm.
Rear CompactPCI connectors: 2mm J1 & J2 connectors.
PMC connectors: Three 1mm connectors.
The air-cooled model (AcPC4610E) uses the standard front panel assembly with a PMC bezel cutout.Physical: Transition Module
Physical configuration: Half-length 3U CompactPCI Card 100 x 80mm.
Connectors: 2mm RJ2 connector which maps the rear I/O signals to a SCSI-3 connector. This model also uses a standard rear front panel assembly with a SCSI-3 connector cutout.PMC and CompactPCI bus Compliance
Meets PCI specification version 2.3, CompactPCI specification PICMG 2.3 R1.0, and PMC specification P1386.1.
Data transfer bus: Slave with 32-bit, 16-bit, and 8-bit data transfer operation.
Interrupts: CompactPCI bus INTA# interrupt signal.
PCI Interface: PLX Technology PCI6540 transparent PCI/PCI bridge for data transactions from the PCI bus (system host) to the PMC site. The bridge device provides a 32-bit 33/66 MHz PCI interface. -
Features & Benefits
- 3U CompactPCI card
- Holds one PMC card
- 32-bit 33/66 MHz PCI Interface
- Transparent PCI/PCI bridge for data transactions from the PCI bus to PMC module
- Rear connection I/O access
- Supports both 5V and 3.3V signaling
- -40 to 85°C
-
Specs & Data Sheets
Specs & Catalogs
Manuals
AcPC4610E User Manual (Includes TRANS-C4610 & TRANS-C5210 specifications and Certificate of Volatility) (Log in to download the file)
Catalogs
Drawings & Diagrams
-
Accessories
-
502x Cable Series
- Communication Signal Cables
- Wide assortment of ribbon cables
$40 – $600Select options -
Termination Products
- DIN rail-mount panels
- 50 screw terminals on 50-pin connector termination panels
- 50 screw terminals on SCSI-2 connector termination panels
- 68 screw terminals on SCSI-3 connector termination panels
$165 – $225Select options
-
-
Additional information
Additional information
Weight N/A Dimensions N/A Part Number AcPC4610E: CompactPCI bus carrier card.
Please login to submit this form.