AcPC4610CC: Non-intelligent 3U cPCI PMC Carrier, Conduction-cooled
Product short description:
- One PMC module slot
- Front or rear access I/O
- Plug-and-play carrier configuration and interrupt support
This board provides an easy and low cost solution that enables use of a PMC mezzanine I/O module in a standard 3U CompactPCI computer system. The carrier card acts simply as an adapter to route PCI bus signals to and from the PMC module through the CompactPCI card slot edge connector. All Acromag PMC modules and those from other vendors are supported.
This board uses a PLX Technology PCI6540 transparent PCI/PCI bridge for data transactions from the PCI bus (system host) to the PMC site. The bridge device provides a 32-bit 33/66 MHz PCI interface.
A heat frame enables conduction cooling in applications where ambient or forced air can’t provide adequate cooling. This unit is ideal for airborne systems, deployment in battleground equipment, and other situations with advanced thermal management requirements. Field I/O signals are routed through the carrier card’s rear J2 connector.
An air-cooled rear transition board, Acromag Model TRANS-C4610, is available to map the field I/O on the PMC module to the rear of the CompactPCI system.
Specifications
Environmental
Operating temperature: -40 to 85°C (conduction-cooled.)
Storage temperature: -55 to 100°C.
Relative humidity: 5-95% non-condensing
American National Standard for 2mm Connector Equipment: Practice on Conduction Cooled Euroboards: ANSI/VITA 30.1-2002.
American National Standard for Conduction Cooled PMC: ANSI/VITA 20-2001(R2005).
Power (received from the CompactPCI 3U Back Plane):
3.3V DC (±5%)*: 135mA typical, 150mA max.
5.0V DC (±5%)*: 50mA typical, 70mA max.
±12V DC (±5%)**: Per PMC module.
* With no PMC module installed, ±12V DC not used.
** Max. power 7.5W (total all supplies) per PMC standard.
MTBF: Call factory
Physical: CompactPCI Carrier Card
Physical configuration: 3U CompactPCI Card: 100 x 160mm.
Rear CompactPCI connectors: 2mm J1 & J2 connectors.
PMC connectors: Three 1mm connectors.
The conduction-cooled model (AcPC4610CC) uses a conduction-cooled frame with wedge-loks® and thermo bars.
Physical: Transition Module
Physical configuration: Half-length 3U CompactPCI Card 100 x 80mm.
Connectors: 2mm RJ2 connector which maps the rear I/O signals to a SCSI-3 connector. This model also uses a standard rear front panel assembly with a SCSI-3 connector cutout.
PMC and CompactPCI bus Compliance
Meets PCI specification version 2.3, CompactPCI specification PICMG 2.3 R1.0, and PMC specification P1386.1.
Data transfer bus: Slave with 32-bit, 16-bit, and 8-bit data transfer operation.
Interrupts: CompactPCI bus INTA# interrupt signal. PCI Interface: PLX Technology PCI6540 transparent PCI/PCI bridge for data transactions from the PCI bus (system host) to the PMC site. The bridge device provides a 32-bit 33/66 MHz PCI interface.
- 3U CompactPCI card
- Holds one PMC card
- 32-bit 33/66 MHz PCI Interface
- Transparent PCI/PCI bridge for data transactions from the PCI bus to PMC module
- Rear connection I/O access
- Supports both 5V and 3.3V signaling
- Conduction-cooled -40 to 85°C
Specs & Catalogs
Manuals
AcPC4610CC User Manual (Includes TRANS-C4610 & TRANS-C5210 specifications and Certificate of Volatility) (Log in to download the file)
Catalogs
Drawings & Diagrams
-
502x Cable Series
- Communication Signal Cables
- Wide assortment of ribbon cables
$40 – $600Select options -
Termination Products
- DIN rail-mount panels
- 50 screw terminals on 50-pin connector termination panels
- 50 screw terminals on SCSI-2 connector termination panels
- 68 screw terminals on SCSI-3 connector termination panels
$165 – $225Select options
Additional information
Weight | N/A |
---|---|
Dimensions | N/A |
Part Number | AcPC4610CC: CompactPCI bus carrier card |
-
Description
This board provides an easy and low cost solution that enables use of a PMC mezzanine I/O module in a standard 3U CompactPCI computer system. The carrier card acts simply as an adapter to route PCI bus signals to and from the PMC module through the CompactPCI card slot edge connector. All Acromag PMC modules and those from other vendors are supported.
This board uses a PLX Technology PCI6540 transparent PCI/PCI bridge for data transactions from the PCI bus (system host) to the PMC site. The bridge device provides a 32-bit 33/66 MHz PCI interface.
A heat frame enables conduction cooling in applications where ambient or forced air can’t provide adequate cooling. This unit is ideal for airborne systems, deployment in battleground equipment, and other situations with advanced thermal management requirements. Field I/O signals are routed through the carrier card’s rear J2 connector.
An air-cooled rear transition board, Acromag Model TRANS-C4610, is available to map the field I/O on the PMC module to the rear of the CompactPCI system.
Specifications
Environmental
Operating temperature: -40 to 85°C (conduction-cooled.)
Storage temperature: -55 to 100°C.
Relative humidity: 5-95% non-condensing
American National Standard for 2mm Connector Equipment: Practice on Conduction Cooled Euroboards: ANSI/VITA 30.1-2002.
American National Standard for Conduction Cooled PMC: ANSI/VITA 20-2001(R2005).
Power (received from the CompactPCI 3U Back Plane):
3.3V DC (±5%)*: 135mA typical, 150mA max.
5.0V DC (±5%)*: 50mA typical, 70mA max.
±12V DC (±5%)**: Per PMC module.
* With no PMC module installed, ±12V DC not used.
** Max. power 7.5W (total all supplies) per PMC standard.
MTBF: Call factoryPhysical: CompactPCI Carrier Card
Physical configuration: 3U CompactPCI Card: 100 x 160mm.
Rear CompactPCI connectors: 2mm J1 & J2 connectors.
PMC connectors: Three 1mm connectors.
The conduction-cooled model (AcPC4610CC) uses a conduction-cooled frame with wedge-loks® and thermo bars.Physical: Transition Module
Physical configuration: Half-length 3U CompactPCI Card 100 x 80mm.
Connectors: 2mm RJ2 connector which maps the rear I/O signals to a SCSI-3 connector. This model also uses a standard rear front panel assembly with a SCSI-3 connector cutout.PMC and CompactPCI bus Compliance
Meets PCI specification version 2.3, CompactPCI specification PICMG 2.3 R1.0, and PMC specification P1386.1.
Data transfer bus: Slave with 32-bit, 16-bit, and 8-bit data transfer operation.
Interrupts: CompactPCI bus INTA# interrupt signal. PCI Interface: PLX Technology PCI6540 transparent PCI/PCI bridge for data transactions from the PCI bus (system host) to the PMC site. The bridge device provides a 32-bit 33/66 MHz PCI interface. -
Features & Benefits
- 3U CompactPCI card
- Holds one PMC card
- 32-bit 33/66 MHz PCI Interface
- Transparent PCI/PCI bridge for data transactions from the PCI bus to PMC module
- Rear connection I/O access
- Supports both 5V and 3.3V signaling
- Conduction-cooled -40 to 85°C
-
Tech Papers
How to Keep Heat in Check with Conduction Cooling Application NoteCurrent application demands of PCI Mezzanine Card (PMC) modules have grown from the simple addition of I/O and low-level communications to the servicing and off-loading of high performance software defined radio (SDR), digital signal processing (DSP), co-processing, and now re-configurable FPGA-based computing with gigabit interfaces. This trend of putting more and more processing power on... -
Specs & Data Sheets
Specs & Catalogs
Manuals
AcPC4610CC User Manual (Includes TRANS-C4610 & TRANS-C5210 specifications and Certificate of Volatility) (Log in to download the file)
Catalogs
Drawings & Diagrams
-
Accessories
-
502x Cable Series
- Communication Signal Cables
- Wide assortment of ribbon cables
$40 – $600Select options -
Termination Products
- DIN rail-mount panels
- 50 screw terminals on 50-pin connector termination panels
- 50 screw terminals on SCSI-2 connector termination panels
- 68 screw terminals on SCSI-3 connector termination panels
$165 – $225Select options
-
-
Additional information
Additional information
Weight N/A Dimensions N/A Part Number AcPC4610CC: CompactPCI bus carrier card
Please login to submit this form.