AcPC8635A: Nonintelligent 3U cPCI IP Carrier, Rear I/O
Product short description:
- Two IP module slots
- Rear access I/O
- Plug-and-play carrier configuration and interrupt support
The AcPC8635A is a non-intelligent slave board that interfaces two IP modules to the CompactPCI® (cPCI) bus.
All 100 I/O points are brought out the rear J2 connector. This convenience eliminates messy cables from hanging out the front of the cage. In addition to a more efficient cage wiring design, it is also much easier to insert and replace boards.
The AcPC8635A is a drop in replacement for the AcPC8635, please see the known differences document below for more information.
Known difference between the AcPC8635 and the AcPC8634A statement.
Performance Specifications
General
Acromag’s carrier boards provide full data access to the IP module’s I/O, ID and interrupt spaces. With full access to the programmable registers, you can easily configure and control the operation of the IP modules from the cPCI bus.
Up to two interrupt requests are supported for each IP module. All board interrupts are mapped to PCI bus INTA# signal.
Individual passive filters on each IP power supply line provide optimum filtering and noise isolation between the IP modules and the carrier board.
IP Compliance (ANSI/VITA 4)
Meets IP specs per ANSI/VITA 4-1995 (8MHz operation only) and IP I/O mapping to J2 per PICMG 2.4 R1.0.
Electrical/mechanical interface: Supports single or double size IP modules.
IP Module I/O space, ID space, INT, and MEM space supported.
Interrupts: Supports two interrupt requests per IP module and interrupt acknowledge cycles via access to IP INT space.
CompactPCI bus Compliance
Meets PCI spec. V2.1 and PICMG 2.0, R2.1.
Data transfer bus: Slave with 32-bit, 16-bit, and 8-bit data transfer operation. 32-bit read/write accesses are implemented as two 16-bit transfers to the IPs.
Interrupts: CompactPCI bus INTA# interrupt signal. Up to two requests sourced from each IP mapped to INTA#. Interrupts come from IP modules via access to IP module INT space.
32-bit memory space: Upon power-up, the system auto-configuration process (plug & play) maps the carrier’s base address (for a 1K byte block of memory) into the PCI bus 32-bit memory space.
Power Requirements
Power
3.3V (±5%): 300mA maximum.
5V (±5%): 30mA maximum.
±12V (±5%): 0mA (not used).
Plus IP module load.
MTBF: Contact factory
Environmental
Operating temperature: 0 to 70°C (AcPC8635A model) or -40 to 85°C (AcPC8635AE model).
Storage temperature: -55 to 100°C.
Relative humidity: 5 to 95% non-condensing.
- Two industry-standard IP module slots
- Board resides in memory space
- Supports IP module I/O, ID, INT, and MEM spaces
- Supports 8 and 32 MHz operation
- 100 I/O points with rear access
- High-density rear connectors
- Compatible with 32-bit CompactPCI® backplane
- Plug-and-play carrier configuration and interrupt support
- Two interrupt channels per IP module
- Front panel LEDs
- Supervisory circuit for reset generation
- Individually filtered and fused power to each IP
- • Ruggedized with ESD strip and EMC front panel
- • Easily integrate IPs with your software using RTOS VxWorks, Linux, or Win DLL for Windows® 2000/XP/Vista/7 32-bit systems
Specs & Catalogs
Manuals
AcPC8635A User Manual (Log in to download the file)
Catalogs
Drawings & Diagrams
-
502x Cable Series
- Communication Signal Cables
- Wide assortment of ribbon cables
$40 – $600Select options -
Termination Products
- DIN rail-mount panels
- 50 screw terminals on 50-pin connector termination panels
- 50 screw terminals on SCSI-2 connector termination panels
- 68 screw terminals on SCSI-3 connector termination panels
$165 – $225Select options
Additional information
Weight | N/A |
---|---|
Dimensions | N/A |
Part Number | AcPC8635A: Holds two IP modules (rear connector access)., AcPC8635AE: Holds two IP modules (rear connector access), extended temp.range |
-
Description
The AcPC8635A is a non-intelligent slave board that interfaces two IP modules to the CompactPCI® (cPCI) bus.
All 100 I/O points are brought out the rear J2 connector. This convenience eliminates messy cables from hanging out the front of the cage. In addition to a more efficient cage wiring design, it is also much easier to insert and replace boards.
The AcPC8635A is a drop in replacement for the AcPC8635, please see the known differences document below for more information.
Known difference between the AcPC8635 and the AcPC8634A statement.Performance Specifications
General
Acromag’s carrier boards provide full data access to the IP module’s I/O, ID and interrupt spaces. With full access to the programmable registers, you can easily configure and control the operation of the IP modules from the cPCI bus.
Up to two interrupt requests are supported for each IP module. All board interrupts are mapped to PCI bus INTA# signal.
Individual passive filters on each IP power supply line provide optimum filtering and noise isolation between the IP modules and the carrier board.
IP Compliance (ANSI/VITA 4)
Meets IP specs per ANSI/VITA 4-1995 (8MHz operation only) and IP I/O mapping to J2 per PICMG 2.4 R1.0.
Electrical/mechanical interface: Supports single or double size IP modules.
IP Module I/O space, ID space, INT, and MEM space supported.
Interrupts: Supports two interrupt requests per IP module and interrupt acknowledge cycles via access to IP INT space.CompactPCI bus Compliance
Meets PCI spec. V2.1 and PICMG 2.0, R2.1.
Data transfer bus: Slave with 32-bit, 16-bit, and 8-bit data transfer operation. 32-bit read/write accesses are implemented as two 16-bit transfers to the IPs.
Interrupts: CompactPCI bus INTA# interrupt signal. Up to two requests sourced from each IP mapped to INTA#. Interrupts come from IP modules via access to IP module INT space.
32-bit memory space: Upon power-up, the system auto-configuration process (plug & play) maps the carrier’s base address (for a 1K byte block of memory) into the PCI bus 32-bit memory space.Power Requirements
Power
3.3V (±5%): 300mA maximum.
5V (±5%): 30mA maximum.
±12V (±5%): 0mA (not used).
Plus IP module load.
MTBF: Contact factoryEnvironmental
Operating temperature: 0 to 70°C (AcPC8635A model) or -40 to 85°C (AcPC8635AE model).
Storage temperature: -55 to 100°C.
Relative humidity: 5 to 95% non-condensing. -
Features & Benefits
- Two industry-standard IP module slots
- Board resides in memory space
- Supports IP module I/O, ID, INT, and MEM spaces
- Supports 8 and 32 MHz operation
- 100 I/O points with rear access
- High-density rear connectors
- Compatible with 32-bit CompactPCI® backplane
- Plug-and-play carrier configuration and interrupt support
- Two interrupt channels per IP module
- Front panel LEDs
- Supervisory circuit for reset generation
- Individually filtered and fused power to each IP
- • Ruggedized with ESD strip and EMC front panel
- • Easily integrate IPs with your software using RTOS VxWorks, Linux, or Win DLL for Windows® 2000/XP/Vista/7 32-bit systems
-
Specs & Data Sheets
Specs & Catalogs
Manuals
AcPC8635A User Manual (Log in to download the file)
Catalogs
Drawings & Diagrams
-
Accessories
-
502x Cable Series
- Communication Signal Cables
- Wide assortment of ribbon cables
$40 – $600Select options -
Termination Products
- DIN rail-mount panels
- 50 screw terminals on 50-pin connector termination panels
- 50 screw terminals on SCSI-2 connector termination panels
- 68 screw terminals on SCSI-3 connector termination panels
$165 – $225Select options
-
-
Additional information
Additional information
Weight N/A Dimensions N/A Part Number AcPC8635A: Holds two IP modules (rear connector access)., AcPC8635AE: Holds two IP modules (rear connector access), extended temp.range
Please login to submit this form.