Click to zoom

Please sign in or register to see model options and to add products to your cart.

Product short description:
  • Four IP module slots
  • Rear access I/O
  • Plug-and-play carrier configuration and interrupt support

The AcPC8625A is a nonintelligent slave board that interfaces four IP modules to the CompactPCI (cPCI) bus.

 

 

AcPC8625A: Nonintelligent 6U cPCI IP Carrier Description

The AcPC8625A is a nonintelligent slave board that interfaces four IP modules to the CompactPCI (cPCI) bus.

All 200 I/O points are brought out the rear J4 and J5 connectors. This convenience eliminates messy cables from hanging out the front of the cage. In addition to a more efficient cage wiring design, it is also much easier to insert and replace boards. And with Acromag’s 80mm transition module (TRANS-C200), all 200 I/O points are easily ported out the back of the cage.

Performance Specifications

General

Acromag’s carrier boards provide full data access to the IP module’s I/O, ID, interrupt spaces, and memory. With full access to the programmable registers, you can easily configure and control the operation of the IP modules from the CompactPCI bus.

Up to two interrupt requests are supported for each IP module. All board interrupts are mapped to PCI bus INTA# signal.

Individual passive filters on each IP power supply line provide optimum filtering and noise isolation between the IP modules and the carrier board.

IP Compliance (ANSI/VITA 4): Meets IP specs per ANSI/VITA 4-1995 (8MHz and 32MHz) and IP I/O mapping to PICMG 2.4 R1.0.

Electrical/mechanical interface: Supports single or double size IP modules. 32-bit IP modules are not supported.

IP Module I/O space, ID space, INT space, and MEM space supported.

Interrupts: Supports two interrupt requests per IP module and interrupt acknowledge cycles via access to IP INT space.

CompactPCI bus Compliance

Meets PCI spec. V2.1 and PICMG 2.0, R2.1.
Data transfer bus: Slave with 32-bit, 16-bit, and 8-bit data transfer operation 32-bit read/write accesses are implemented as two 16-bit transfers to the IPs.
Interrupts: CompactPCI bus INTA# interrupt signal. Up to two requests sourced from each IP mapped to INTA#. Interrupt vectors come from IP modules via access to IP module INT space.
Plug-and-Play: The system maps the base address into the PCI bus 32-bit memory space.

Power Requirements

Power
3.3V (±5%): 300mA maximum.
5V (±5%): 30mA maximum.
±12V (±5%): 0mA (not used).
Plus IP module load.
MTBF: Contact factory

Environmental

Operating temperature: -25 to 85°C (AcPC8625) or -40 to 85°C (AcPC8625E models).
Storage temperature: -25 to 85°C (AcPC8625) or -40 to 85°C (AcPC8625E models).
Relative humidity: 5 to 95% non-condensing.

The AcPC8625A is a drop in replacement for the AcPC8625, please see known difference statement below.
Known difference between the AcPC8625 and the AcPC8625A statement.

 

 

  • Four industry-standard IP module slots
  • Board resides in memory space
  • Supports IP module I/O, ID, INT and MEM spaces
  • 200 I/O points with rear access
  • High-density rear connectors
  • Compatible with all CompactPCI CPUs
  • Plug-and-play carrier configuration and interrupt support
  • Two interrupts per IP module
  • Front panel LEDs
  • Supervisory circuit for reset generation
  • Individually filtered and fused power to each IP
  • Ruggedized with ESD strip and EMC front panel
  • Easily integrate IPs with your software using RTOS VxWorks, Linux, or Win DLL for Windows® 2000/XP/Vista/7 32-bit systems

 

 

  • Compare

    Embedded Cables

    • Communication Signal Cables
    • Wide assortment of ribbon cables
    Select options
  • Compare

    Termination Products

    • DIN rail-mount panels
    • 50 screw terminals on 50-pin connector termination panels
    • 50 screw terminals on SCSI-2 connector termination panels
    • 68 screw terminals on SCSI-3 connector termination panels
    Select options
  • Compare

    Transition Modules

    • Various transition modules
    Select options

Additional information

Weight N/A
Dimensions N/A
Part Number

AcPC8625A: holds four modules, AcPC8625AE: holds four modules, extended temp. range

  • Description

    AcPC8625A: Nonintelligent 6U cPCI IP Carrier Description

    The AcPC8625A is a nonintelligent slave board that interfaces four IP modules to the CompactPCI (cPCI) bus.

    All 200 I/O points are brought out the rear J4 and J5 connectors. This convenience eliminates messy cables from hanging out the front of the cage. In addition to a more efficient cage wiring design, it is also much easier to insert and replace boards. And with Acromag’s 80mm transition module (TRANS-C200), all 200 I/O points are easily ported out the back of the cage.

    Performance Specifications

    General

    Acromag’s carrier boards provide full data access to the IP module’s I/O, ID, interrupt spaces, and memory. With full access to the programmable registers, you can easily configure and control the operation of the IP modules from the CompactPCI bus.

    Up to two interrupt requests are supported for each IP module. All board interrupts are mapped to PCI bus INTA# signal.

    Individual passive filters on each IP power supply line provide optimum filtering and noise isolation between the IP modules and the carrier board.

    IP Compliance (ANSI/VITA 4): Meets IP specs per ANSI/VITA 4-1995 (8MHz and 32MHz) and IP I/O mapping to PICMG 2.4 R1.0.

    Electrical/mechanical interface: Supports single or double size IP modules. 32-bit IP modules are not supported.

    IP Module I/O space, ID space, INT space, and MEM space supported.

    Interrupts: Supports two interrupt requests per IP module and interrupt acknowledge cycles via access to IP INT space.

    CompactPCI bus Compliance

    Meets PCI spec. V2.1 and PICMG 2.0, R2.1.
    Data transfer bus: Slave with 32-bit, 16-bit, and 8-bit data transfer operation 32-bit read/write accesses are implemented as two 16-bit transfers to the IPs.
    Interrupts: CompactPCI bus INTA# interrupt signal. Up to two requests sourced from each IP mapped to INTA#. Interrupt vectors come from IP modules via access to IP module INT space.
    Plug-and-Play: The system maps the base address into the PCI bus 32-bit memory space.

    Power Requirements

    Power
    3.3V (±5%): 300mA maximum.
    5V (±5%): 30mA maximum.
    ±12V (±5%): 0mA (not used).
    Plus IP module load.
    MTBF: Contact factory

    Environmental

    Operating temperature: -25 to 85°C (AcPC8625) or -40 to 85°C (AcPC8625E models).
    Storage temperature: -25 to 85°C (AcPC8625) or -40 to 85°C (AcPC8625E models).
    Relative humidity: 5 to 95% non-condensing.

    The AcPC8625A is a drop in replacement for the AcPC8625, please see known difference statement below.
    Known difference between the AcPC8625 and the AcPC8625A statement.

     

     

  • Features & Benefits

    • Four industry-standard IP module slots
    • Board resides in memory space
    • Supports IP module I/O, ID, INT and MEM spaces
    • 200 I/O points with rear access
    • High-density rear connectors
    • Compatible with all CompactPCI CPUs
    • Plug-and-play carrier configuration and interrupt support
    • Two interrupts per IP module
    • Front panel LEDs
    • Supervisory circuit for reset generation
    • Individually filtered and fused power to each IP
    • Ruggedized with ESD strip and EMC front panel
    • Easily integrate IPs with your software using RTOS VxWorks, Linux, or Win DLL for Windows® 2000/XP/Vista/7 32-bit systems

     

     

  • Specs & Data Sheets

  • Accessories

    • Compare

      Embedded Cables

      • Communication Signal Cables
      • Wide assortment of ribbon cables
      Select options
    • Compare

      Termination Products

      • DIN rail-mount panels
      • 50 screw terminals on 50-pin connector termination panels
      • 50 screw terminals on SCSI-2 connector termination panels
      • 68 screw terminals on SCSI-3 connector termination panels
      Select options
    • Compare

      Transition Modules

      • Various transition modules
      Select options
  • Additional information

    Additional information

    Weight N/A
    Dimensions N/A
    Part Number

    AcPC8625A: holds four modules, AcPC8625AE: holds four modules, extended temp. range