• Thermocouple (J, K, T, R, S, E, B, N), RTD (Pt, Ni, Cu), millivolt (±100mV DC), resistance (0 to 500 ohms) input
• Single or dual mechanical relay alarm outputs
• 10-36V DC power
• Software configured
• Multi-function alarms (limit, window, deviation, rate-of-change, peak/valley detection)
• On/off controller capability

IntelliPack alarms compare inputs against user-defined limit set-points to control built-in relays.

• Thermocouple, RTD, milliVolt, and Resistance Input
• 0 to 20mA DC, 0 to 10V DC output
• Limit Alarm
• 10-36V DC power
• Software configured
• Performs linearization, square root extraction, and optional limit alarm functions

These transmitters isolate and convert sensor inputs to noise-free, proportional DC current or voltage output signals. An optional relay output adds a local limit alarm function.

• ±100V or 0 to 22mA DC input ranges or 2 input channels, ±100V or 0 to 22mA DC input ranges (AC current with optional sensor)
• Single or dual mechanical relays
• 10-36V DC power
• Software configured; multi-function alarms (limit, window, deviation, rate-of-change, peak/valley detection); on/off controller capability

IntelliPack alarms compare inputs against user-defined limit set-points to control built-in relays.  

• 2 input channels, thermocouple (types J, K, T, R, S, E, B, N), or millivolt (±100mV DC) input
• Dual mechanical relays output
• 10-36V DC power
• Software configured; multi-function alarms (limit, window, deviation, rate-of-change, peak/valley detection); on/off controller capability

IntelliPack alarms compare inputs against user-defined limit set-points to control built-in relays.

• 0 to 50KHz, 0 to 65535 pulses input
• 0 to 20mA DC, 0 to 10V DC output
• Mechanical alarm relay (25V @ 5A)
• 10-36V DC power
• Software configured; pulse counter; signal averaging; optional limit alarm functions

These transmitters isolate and convert sensor inputs to noise-free, proportional DC current or voltage output signals. An optional relay output adds a local limit alarm function.

• 4 input channels
• 0 to 20mA DC (0 to 20A AC with AC sensor) or ±10V DC input range
• 4 alarm channels, open drain MOSFETS (1A DC loads, 0 to 35V DC)
• 10 to 36V DC, 24V AC power
• Modbus RTU high-speed RS-485

This signal conditioner is a four-channel analog input module with four discrete outputs. It provides isolation between input, output, power, and network circuits.

• 4 input channels, thermocouple (types J, K, T, R, S, E, B, N) or millivolt (±100mV DC) input
• 4 alarm channels, open drain MOSFETS (1A DC loads, 0 to 35V DC)
• 10 to 36V DC, 24V AC power
• Modbus-RTU high-speed RS-485

This signal conditioner is a four-channel analog input module with four discrete outputs. It filters and linearizes thermocouple inputs while providing isolation between input, output, power, and network circuits. Cold junction compensation and upscale/downscale sensor break detection are standard.  

• 2 input channels, 0 to 50KHz in 3 selectable ranges: Amplitudes up to 140V AC peak, Amplitudes up to 200V peak, Pulse counter range of 0 to 65535
• Solid-state discrete output relays (1A DC loads), 0 to 48V DC
• 10 to 36V DC, 24V AC power
• Modbus-RTU high-speed RS-485

This signal conditioner is a two-channel analog input module with discrete outputs and Modbus communication. It conditions periodic or pulse waveform inputs and provides solid-state relays for limit alarms or ON/OFF control.