The AcPC8625A is a nonintelligent slave board that interfaces four IP modules to the CompactPCI (cPCI) bus. All 200 I/O points are brought out the rear J4 and J5 connectors. This convenience eliminates messy cables from hanging out the front of the cage. In addition to a more efficient cage wiring design, it is also much easier to insert and replace boards. And with Acromag’s 80mm transition module (TRANS-C200), all 200 I/O points are easily ported out the back of the cage.

Performance Specifications

General

Acromag’s carrier boards provide full data access to the IP module’s I/O, ID, interrupt spaces, and memory. With full access to the programmable registers, you can easily configure and control the operation of the IP modules from the CompactPCI bus. Up to two interrupt requests are supported for each IP module. All board interrupts are mapped to PCI bus INTA# signal. Individual passive filters on each IP power supply line provide optimum filtering and noise isolation between the IP modules and the carrier board. IP Compliance (ANSI/VITA 4): Meets IP specs per ANSI/VITA 4-1995 (8MHz and 32MHz) and IP I/O mapping to PICMG 2.4 R1.0. Electrical/mechanical interface: Supports single or double size IP modules. 32-bit IP modules are not supported. IP Module I/O space, ID space, INT space, and MEM space supported. Interrupts: Supports two interrupt requests per IP module and interrupt acknowledge cycles via access to IP INT space.

CompactPCI bus Compliance

Meets PCI spec. V2.1 and PICMG 2.0, R2.1. Data transfer bus: Slave with 32-bit, 16-bit, and 8-bit data transfer operation 32-bit read/write accesses are implemented as two 16-bit transfers to the IPs. Interrupts: CompactPCI bus INTA# interrupt signal. Up to two requests sourced from each IP mapped to INTA#. Interrupt vectors come from IP modules via access to IP module INT space. Plug-and-Play: The system maps the base address into the PCI bus 32-bit memory space.

Power Requirements

Power 3.3V (±5%): 300mA maximum. 5V (±5%): 30mA maximum. ±12V (±5%): 0mA (not used). Plus IP module load. MTBF: Contact factory

Environmental

Operating temperature: -25 to 85°C (AcPC8625) or -40 to 85°C (AcPC8625E models). Storage temperature: -25 to 85°C (AcPC8625) or -40 to 85°C (AcPC8625E models). Relative humidity: 5 to 95% non-condensing. The AcPC8625A is a drop in replacement for the AcPC8625, please see known difference statement below. Known difference between the AcPC8625 and the AcPC8625A statement.

Showing 1–16 of 31 results

  • Compare

    AcPC8625A: Nonintelligent 6U cPCI IP Carrier

    • Four IP module slots
    • Rear access I/O
    • Plug-and-play carrier configuration and interrupt support
    $900$1,020
    Select options
  • Compare

    AcPC8630A: Nonintelligent 3U cPCI IP Carrier, Front I/O

    • Two IP module slots
    • Front access I/O
    • Plug-and-play carrier configuration and interrupt support
    $780$900
    Select options
  • Compare

    AcPC8635A: Nonintelligent 3U cPCI IP Carrier, Rear I/O

    • Two IP module slots
    • Rear access I/O
    • Plug-and-play carrier configuration and interrupt support
    $780$900
    Select options
  • Compare

    APC8620A: Non-intelligent PCI Bus Carrier for IP Modules

    • Holds five IP modules
    $900
    Select options
  • Compare

    APC8621A: Non-intelligent PCI Bus Carrier, Half-Length

    • Nonintelligent PCI bus carrier
    • Holds three IP modules
    $720
    Select options
  • Compare

    IP-EP200: Cyclone II FPGA with Digital I/O (JTAG-configured)

    • Up to 48 TTL or 24 differential RS485
    • Altera Cyclone II EP2C20 FPGA programmable via JTAG port or via the IP bus directly
    $1,300$1,430
    Select options
  • Compare

    IP220A: Analog Output Industry Pack Module, 12-bit D/A

    • 8 or 16 voltage output channels
    • Independent D/A converter on each channel
    • 11µS settling time
    • ±10V output range
    $865$1,395
    Select options
  • Compare

    IP230A: Analog Output Module, 16-bit D/A

    • 4 or 8 voltage output channels
    • Individual D/A converters on each channel
    • 10µS settling time
    • Selectable output range (±5V, ±10V, 0-10V)
    $1,010$1,490
    Read more
  • Compare

    IP231: Analog Output Module, 16-bit D/A

    • 8 or 16 voltage output channels
    • Independent D/A converter on each channel
    • 13µS settling time
    • ±10V output range
    $1,240$1,740
    Read more
  • Compare

    IP235A: Analog Output Module, 16-bit D/A w/RAM Buffer

    • 8 voltage output channels
    • Individual D/A converters on each channel
    • 10µS settling time
    • Selectable output range (±5V, ±10V, 0-10V)
    $1,705$1,825
    Read more
  • Compare

    IP320A: Analog Input Module, 12-bit A/D

    • 20 differential or 40 single-ended input channels
    • 200KHz throughput
    • 4.5µS/conversion
    • Selectable input range (±5V, ±10V, 0-10V)
    $780$915
    Read more
  • Compare

    IP330A: Analog Input Module, 16-bit A/D

    • 16 differential or 32 single-ended input channels
    • 200KHz throughput
    • 5µS/conversion
    • Selectable input range (±5V, ±10V, 0-5V, 0-10V)
    $1,360$1,490
    Read more
  • Compare

    IP340: Analog Input Module, Simultaneous Sample & Hold

    • 16 differential inputs (two 8-channel groups)
    • 12 or 14-bit A/D
    • 125KHz throughput
    • 8µS conversion time for 8-channel group
    • 512 sample FIFO buffer, ±10V input range
    $1,455$1,800
    Read more
  • Compare

    IP400: Digital Input Module, High Voltage Inputs

    • 40 input channels
    • 0-60V DC input range
    • Change-of-state/level interrupts (up to 12 channels)
    $470$590
    Read more
  • Compare

    IP405: Digital Output Module, High Voltage Outputs

    • 40 low-side switch output channels
    • 0-60V DC output range
    • High output current (up to 1A per channel)
    $530$660
    Read more
  • Compare

    IP408: Digital Input/Output Module, High Voltage I/O

    • 32 bi-directional digital input and/or output channels
    • 0-60V DC input and output range
    • Low-side output switches
    • Outputs sink up to 1A per channel
    • Change-of-state and level interrupts (up to 8 channels)
    $565$700
    Read more