Input (981 & 983 models) Input Type: Twelve active-low, buffered inputs, with a common connection. Built-in 5.6K ohm pullups to excitation terminal socketed for 4-channel groups. Input Signal Voltage Range: 0 to 35V DC, maximum. Input Impedance: 100K ohms, typical. Input Signal Threshold: TTL compatible with 100mV of hysteresis, typical. Output (982 & 983 models) Output Type: 12 independent, open-drain, MOSFET switches. Output Voltage and ON Resistance: 0 to 35V DC max. (0 to 500mA/channel continuous). 0.28 ohms maximum ON resistance. Environmental Ambient Operating Temperature: -25 to 70°C (-13 to 158F). Ambient Storage Temperature: -40 to 85°C (-40 to 185°F). Relative Humidity: 5 to 95%, non-condensing. Isolation: 1500V AC for 60 seconds or 250V AC continuous. 3-way isolation between I/O, network, and power.

Communication

Connector: Shielded RJ-45 sockets, 8-pin, 10BaseT/100BaseTX. Wiring: Wired MDI. 9xxEN I/O modules do NOT support autocrossover. 900EN switch supports auto-crossover. Protocol: EtherNet/IP or Modbus TCP/IP with web browser configuration. EtherNet/IP supports PCCC object for communication with legacy PLCs (e.g. SLC505). IP Address: Default static IP address is 128.1.1.100. Port: Ethernet Modbus TCP/IP models (9xxEN-4xxx): Up to 10 Modbus TCP/IP sockets supported. EtherNet/IP models (9xxEN-6xxx): Up to 10 EtherNet/IP sockets and 1 Modbus TCP/IP socket. Data Rate: Auto-sensed, 10Mbps or 100Mbps. Duplex: Auto-negotiated, full or half-duplex. Compliance: IEEE 802.3, 802.3u, 802.3x, Ethernet II. Configuration: Web page for configuration and control is built-in with Ethernet access via a standard web browser. Communication Distance: Distance between network devices is generally limited to 100 meters using recommended cable. Distances may be extended using hubs and switches. Address: IP address is automatically acquired at startup. Unit may be configured to retrieve this address from the network server using BOOTP (Bootstrap Protocol), or via DHCP (Dynamic Configuration Protocol). A static IP address is also user-programmable. A default toggle switch sets the static IP address to the default factory address of 128.1.1.100 for initial configuration.

Environmental

Isolation: I/O channel, power, and network circuits are isolated from each other for common-mode voltages up to 250VAC, or 354V DC off DC power ground, on a continuous basis (will withstand 1500VAC dielectric strength test for one minute without breakdown). Complies with test requirements of ANSI/ISA-82.01- 1988 for voltage rating specified.

Electromagnetic Compatibility (EMC)

Immunity per European Norm EN50082-1. Emissions per European Norm EN50081-1. Electrostatic Discharge (ESD) Immunity Per EN61000-4-2. Radiated Field Immunity (RFI) Per EN61000-4-3 and ENV50204. Electrical Fast Transient Immunity (EFT) Per EN61000-4-4. Conducted RF Immunity (CRFI) Per EN61000-4-6. Surge Immunity Per EN61000-4-5. Radiated Frequency Emissions Per EN55022 Class B.

Showing all 9 results

  • Compare
    Compare

    981EN, 982EN, 983EN: Ethernet Discrete I/O Modules

    • 12-channel discrete input and/or output
    • Ethernet/IP, Modbus TCP/IP, i2o peer-to-peer messaging
    • Input Range: 0 to 35V DC
    • Output Range: 0 to 35V DC
    • Network Communication: EtherNet/IP or Modbus TCP/IP 10/100Mbps with automatic data rate negotiation
    • Power Requirement: 15 to 36V DC supply (2 Watts) required
    • Approvals: CE/ATEX marked. UL, cUL listed, Class I; Div. 2; Groups A, B, C, D. EtherNet/IP, Modbus/TCP conformance tested.
    $385 – $410
    Read more
  • Compare
    Compare

    XT1110: 16-Channel Discrete Ethernet I/O Modules with Sinking Outputs

    • 16 discrete tandem input/output channels
    • Input: 0-32V DC, TTL thresholds
    • Output: 0-32V DC, open-drain, up to 250mA
    • Ethernet Communication: Modbus TCP/IP,  Ethernet/IP, Profinet, i2o® peer-to-peer, 10/100Base-T(X) PriorityChannel™ device determinism
    • Power Requirement: 12 to 32V DC (2.5W)
    • Approvals: CE compliant. UL/cUL Class I; Div. 2 Zone 2. ATEX Cert. II 3 G Ex nA IIC T4 Gc -40°C < Ta < 80°C
    $320
    Read more
  • Compare
    Compare

    XT1120: 16-Channel Discrete Ethernet I/O Modules with Sourcing Outputs

    • Input: 0-32V DC, TTL thresholds Output: 0-32V DC, open-drain, up to 300mA
    • Ethernet Communication: Modbus TCP/IP, Ethernet/IP, Profinet, i2o® peer-to-peer, 10/100Base-T(X) PriorityChannel™ device determinism
    • Power Requirement: 12 to 32V DC (2.5W)
    • Approvals: CE compliant. UL/cUL Class I; Div. 2 Zone 2. ATEX cert. II 3 G Ex nA IIC T4 Gc -40°C < Ta < 80°C
    $320
    Read more
  • Compare
    Compare

    XT1210: 8-Channel Differential Analog Current Input Module

    • 0-11mA, 0-20mA, 4-20mA, ±20mA, or 0-20 amps AC Input
    • 8 analog differential current input channels
    • 12 to 32V DC Power (2.8W)
    $495
    Read more
  • Compare
    Compare

    XT1220: 8-Channel Differential Analog Voltage Input Module

    • ±5V, ±10V, 0-5V, 0-10V Input
    • 8 analog differential voltage input channels
    • 12 to 32V DC Power (2.8W)
    $495
    Read more
  • Compare
    Compare

    XT1230: 16-Channel Single-Ended Analog Current Input Module

    • 0-11mA, 0-20mA, 4-20mA, ±20mA, or 0-20 amps AC Input
    • 16 analog single-ended current input channels
    • 12 to 32V DC Power (2.8W)
    $595
    Read more
  • Compare
    Compare

    XT1240: 16-Channel Single-Ended Analog DC Voltage Input Module

    • ±5V, ±10V, 0-5V, 0-10V Input
    • 16 analog single-ended voltage input channels
    • 12 to 32V DC Power (2.8W)
    $595
    Read more
  • Compare
    Compare

    XT1530: Analog Output & Digital I/O Ethernet Modules

    • 4 Analog DC Current Outputs
    • 4 Discrete Voltage I/O Channels
    • 12 to 32V DC Power (2.8W)
    $495
    Read more
  • Compare
    Compare

    XT1540: Analog Output & Digital I/O Ethernet Modules

    • 8 Analog DC Voltage Outputs ±10V (calibrated), ±5V (sub-range)
    • 4 Discrete Voltage I/O Channels 0-32V DC
    • 12 to 32V DC Power (2.8W)
    $525
    Read more