The Embedded Computing and I/O Solutions division is focused on high-performance processors, FPGA boards, and I/O products for applications that demand rugged high-performance precise operation.

Showing 1–16 of 21 results

  • Compare

    APC-PMC: Non-intelligent PMC Carrier Card

    • Half-length PCI card
    • Holds one PMC card
    • 32-bit 66 MHz PCI interface
    This board provides an easy and low cost solution that enables use of a PMC mezzanine I/O module in a standard PCI computer system. The carrier card acts simply as an adapter to route PCI bus signals to and from the PMC module through the PCI card slot edge connector.
    Select options
  • Compare

    APC8620A: Non-intelligent PCI Bus Carrier for IP Modules

    • Holds five IP modules
    • Front access I/O
    • Plug-and-play carrier configuration and interrupt support
    This board interfaces industry-standard Industrial I/O Pack (IP) modules to a PCI bus on a PC-based computer system.
    Select options
  • Compare

    APC8621A: Non-intelligent PCI Bus Carrier, Half-Length

    • Nonintelligent PCI bus carrier
    • Holds three IP modules
    • Plug-and-play carrier configuration and interrupt support
    • Two interrupt channels per IP module
    • Supervisory circuit reset generation
    This board interfaces industry-standard Industrial I/O Pack (IP) modules to a PCI bus on a PC-based computer system. The half-length card is ideal for use in smaller PC chassis.
    Select options
  • Compare

    APCe8675: Non-intelligent carrier card

    • 8-lane PCI Express interface
    • Holds one XMC module
    The APCe8675 is a PCIe bus adapter board that allows a PC (PCIe bus master) to control and communicate with the hosted XMC module. It simply acts as an adapter to route signals between the system’s PCIe bus and the XMC module connector.
    Select options
  • Compare

    APCe8775: PCI Express Carrier Card for XMC Modules

    • One XMC mezzanine module slot
    • 3/4-length
    • Non-Intelligent carrier card
    • PCIe x8 interface
    Acromag’s APCe8775 carrier card interfaces an XMC mezzanine module to a PCI Express bus in a PC-based desktop computer system.
    Select options
  • Compare

    IP400: Digital Input Module, High Voltage Inputs

    • 40 input channels
    • 0-60V DC input range
    • Change-of-state/level interrupts (up to 12 channels)
    The IP400 can monitor the on/off (high/low) status of up to 40 devices.
    Select options
  • Compare

    IP405: Digital Output Module, High Voltage Outputs

    • 40 low-side switch output channels
    • 0-60V DC output range
    • High output current (up to 1A per channel)
    The IP405 controls up to 40 low-side switches (open-drain MOSFETs).    
    Select options
  • Compare

    IP408: Digital Input/Output Module, High Voltage I/O

    • 32 bi-directional digital input and/or output channels
    • 0-60V DC input and output range
    • Low-side output switches
    • Outputs sink up to 1A per channel
    • Change-of-state and level interrupts (up to 8 channels)
    The IP408 monitors or controls the on/off (high/low) status of up to 32 devices. Each channel can be used as an input or output.
    Select options
  • Compare

    IP409: Digital Input/Output Module, Differential I/O

    • 24 differential digital input and/or output channels
    • Ruggedized RS-422A/485 transceivers
    • Interrupt support on all channels (change-of-state and high or low level transition)
    The IP409 provides 24 differential I/O channels with interrupts. Each channel is programmable as an input or an output on a bit basis, in any combination.
    Select options
  • Compare

    IP440A: Digital Input Module, Isolated

    • 32 port-isolated input channels
    • ±60V AC/DC input (three ranges)
    • Interrupt support for each channel
    IP440A Industrial I/O Pack (IP) modules provide 32 optically isolated inputs to safely monitor a wide range of digital input voltage levels.
    Select options
  • Compare

    IP445A: Digital Output Module, Isolated

    • 32 port-isolated output channels (bipolar solid state relays)
    • ±60V AC/DC output
    • High/low-side switch configuration
    IP445A modules provide 32 isolated solid-state relay outputs to safely control discrete devices.
    Select options
  • Compare

    IP470A: Digital Output Module, TTL Level

    • 48 bi-directional input/output channels
    • TTL-compatible inputs
    • CMOS-compatible open-drain outputs
    • Interrupt support for each channel
    IP470A Industrial I/O Pack (IP) modules provide 48 general-purpose, bidirectional I/O points to economically monitor and control a large quantity of digital devices.
    Select options
  • Compare

    IP480: Counter/Timer Module

    • Two or six 16-bit (one or three 32-bit) counter/timer channels
    • Event counter
    • Output waveform generator
    • Pulse-width or periodic rate monitor
    • Watchdog timer with isolated relay output
    • Interrupt support
    Consult factory for long-term availability.    
    Select options
  • Compare

    VPX4520: VPX Carrier Card for AcroPack® Modules

    • PCIe x16 Gen 3 interface via Expansion plane
    • One XMC and Four AcroPack slots
    • 6U form factor
    The VPX4520 carrier card provides a simple and cost-effective solution for interfacing one XMC and four AcroPack modules to a VPX computer system. Click here to watch a short AcroMaggie video highlighting the VPX4520 features.  
    Select options
  • Compare

    VPX4521: VPX Carrier Card for AcroPack® Modules

    • PCIe x16 Gen 3 interface via Data plane
    • One XMC and Four AcroPack slots
    • 6U form factor
    The VPX4521 is a member of a 6U OpenVPX mezzanine carrier card family that supports a simple and cost-effective solution for interfacing XMC or AcroPack modules to OpenVPX computer systems. Click here to watch a short AcroMaggie video highlighting the VPX4521 features.    
    Select options
  • Compare

    VPX4812A / VPX4814A: VPX Carrier Cards for XMC Modules

    • Air-cooled, conduction-cooled and REDI versions
    • 3U Single XMC slot
    • PCIe x8 Gen 2 interface
    The VPX4812A can be used as a VPX switch card allowing a host CPU to communicate with up to 3 downstream cards in addition to the XMC card. Each VPX port can be configured to be x4 or x8. The VPX4814A is a peripheral XMC carrier board designed to be used in a system that uses a VPX AcroExpress® CPU.  
    Select options

Embedded I/O Processing Solutions

Acromag’s embedded I/O boards and mezzanine modules are ideal for embedded computer and high-performance control systems. Select from VPX, PCI, CompactPCI, VME, mini PCIe-based AcroPack®, Industry Pack, VPX, XMC and PMC cards to perform a broad range of analog, digital, counter/timer I/O and serial and Ethernet communication functions.

Mini PCIe-based AcroPack®, Industry Pack, VPX, XMC and PMC mezzanine embedded I/O modules plug into VPX, PCI, PCIe, CompactPCI, and other carrier cards to perform A/D, D/A, DIO, counter/timer, communication and other functions.

Acromag embedded I/O boards offer an unmatched balance of features, performance, and price for the best values in embedded I/O. These boards are based on technology and circuit designs with time-tested reliability in thousands of installations.

Real-Time Control Systems