What is FPGA Zynq UltraScale+ with MPSoC?
APZU FPGA-based digital I/O modules provide programmable Xilinx® Zynq UltraScale+ MPSoC
This is a brief overview of some of Acromag’s APZU FPGA Zynq® UltraScale+™ with MPSoC products, as well as the features of AcroPack Zinq UltraScale+, the carrier boards that host AcroPack mezzanine modules. We’ll highlight some of the development tools, the engineering design kit, and the software available. In addition, we’ll discuss some applications and give you an overview of the FPGA products that Acromag supports in the Xilinx offerings.
Table of Contents
- Types of FPGA Zinq UltraScale+ with MPSoC
- Features of AcroPack Zynq UltraScale+ (Table 1)
- APZU Carrier Boards
- APZU FPGA Mezzanine Module
- FPGA Zynq UltraScale+ MPSoC Processors CG
- FPGA Logic Cell
- How is FPGA Device Capacity Measured?
- APZU Peripherals
- EDK, Software Drivers & Development Tools
- FPGA Product Lines Supported
Types of FPGA Zinq UltraScale+ with MPSoC
Acromag’s FPGA Zinq UltraScale+ with MPSoC (Multiprocessor System on a Chip) has three series; the CG series, the EG series, and lastly the EV series. This paper will be focused on the CG series. Acromag uses the XCZU3CG in our product in a 484-pin package (XCZU3CG-2SBVA484I).
The Zinq CG series has a Dual-Core Cortex-A53 (APU) application processor. In addition to that comes a Neon media processing engine and a Dual-Core Cortex R5 (RPU), which is a real-time processing unit.
The EG family has the same set of features of the CG, however it uses a Quad-Core Cortex-A53, and includes a graphics processing unit (GPU) based on the Mali-400MP2. Acromag products are primarily going to be CG, but there is a possibility to do a PIN-compatible EG with the AcroPack Zynq UltraScale+.
Similarly, the Zynq EV family has the same features as the EG: Quad-Core Cortex-A53 and GPU. However, it adds a video codec that can do H.264 and H.265.
Features of AcroPack Zynq UltraScale+
|Feature||Zynq CG||Zynq EG||Zynq EV|
|Dual-Core Cortex-A53 (APU)||X|
|Neon (Media Processing Engine)||X||X||X|
|Dual-Core Cortex R5 (RPU)||X||X||X|
|Graphics Processing Unit||X||X|
Learn more: What are FPGAs and Their Applications?
APZU Carrier Boards
The graphic below shows the APZU-30x. Acromag is introducing three I/O versions; the APZU-301, APZU-A303, and APZU-304.
There are two parts of the Zinq UltraScale+ chip:
- The Processing System (where the multi-processor ARM, Real-time processor and GPU are located)
- The Programmable Logic (PL) side (where the reconfigurable logic is located).
APZU30x Block Diagram
As shown above, we are bringing out an Ethernet that’s 10/100/1000 compatible to the field I/O, a USB 2.0 port, a USB to UART, and a power switch along with a reset switch; these are common amongst all three models.
The I/O is different, however, the APZU-301 will have 28 TTL; the -303 will be a combination of 20 TTL and three R-485/422 serial channels; and the -304 will be 14 low-voltage differential signaling channels.
APZU FPGA Mezzanine Module
There’s also an APZU breakout panel. It’s basically a printed circuit board and has the magnetics on it for the Ethernet so you can connect an RJ45 cable. It has a USB 2.0 connector and a USB to UART COMs port, as well as the digital I/O available on this breakout panel. (More detail about that later.)
The primary boot for the processors is through a micro SD secure digital card and as can be seen in the picture of the AcroPack (right), we’ve got a socket where the micro SD will plug into. There’s also another boot option in case you want to boot through the quad SPI flash. So, you’ll have the ability to load your OS either through the micro SD or the Quad SPI flash. Further, there’s 2 Gbytes of low power DDR4 DRAM on the board, and that’s organized as a 512Mbit x 32.
FPGA Zynq UltraScale+ MPSoC Processors CG
The processors in the CG family as mentioned earlier, are dual-core ARM Cortex A53; this is ARM 8-like. It operates up to 1.3 GHz and it is a 64-bit data and 64-bit instruction. Within that processing unit, there’s a NEON processor, which we will go into more detail about later.
There’s also the dual-core ARM Cortex R5, the real-time processor. This operates up to 533 MHz and is a 32-bit architecture, with hardware-floating point.
Dual Core ARM Cortex-A53
- Up to 1.5GHz Operation
- Harvard Architecture
- 64-bit Data
- 64-bit Instruction
- NEON Processor
Dual Core ARM Cortex R5
- Up to 600 MHz Operation
- 32-bit Architecture
- Hardware Floating-point Unit
- Real-time Processor
Media-Processing Engine: NEON Processor
The media-processing engine called a NEON is a hardware accelerator. It’s part of the application processing unit, and is an advanced single-instruction, multiple-data architecture. Basically, it allows you to accelerate audio and video encoding and decoding and accelerates signal processing algorithms.
FPGA Logic Cell
The graphic below is an example of an FPGA logic cell. It’s identified as a 6-input Look Up Table or LUT (also commonly referred to as a function generator), and the logic cell.
6-input LUT and the Logic Cell
This is shown so you can understand the ability to take a configurable logic block and each one of these configurable logic blocks has eight of these LUTs and 16 flip-flops. So, you’ll be able to reconfigure anyway that you want to interconnect the logic blocks, as well as being able to reprogram them, per your performance requirements.
How is FPGA Device Capacity Measured?
As an illustration, the table below shows the ZU3CG, which is our primary AcroPack Zynq UltraScale+ device, and how it compares to the Artix 7A50T, an Artix 7A200T, and a Kintex 7K325T.
How to Measure Device Capacity
|4-input LUT Ratio Scaling Factor||2.1875||1.6||1.6||1.6|
|Logic Cell = 4-input LUT Calculation||70,560 x 2.1875 = 154,350||32,600 x 1.6 = 52,160||134,000 x 1.6 = 215,360||203,800 x 1.6 = 326,080|
Initially, Xilinx Virtex 4 devices were 4-input LUT / function generators, and the logic cell was said to be equal to a 4-input Look Up Table (LUT) in one flip flop. Therefore, Xilinx still measures the size of their FPGA in terms of 4-input function generators. However, things changed with the introduction of the Virtex 5 family, when the logic cell became a 6-input LUT. So, Xilinx came up with the ratio that a 6-input LUT was 1.6 times a 4-input LUT. Therefore, you were able to come up with an equivalent amount of logic cells, to be able to measure sizes of the different FPGAs.
Acromag offers the AcroPack 7A50T version (APA7-501, -502, -503 and -504), and it has approximately 52,160 logic cells. In contrast, the Zynq UltraScale+ has much more functionality and more resources available. As a result, Xilinx came up with a ratio scaling factor of 2.1875. There’s approximately 70,560 6-input LUTS on this 3CG product. When you do the math, that comes out to 154,000 logic cells. As shown above, that’s roughly about three times the size of a 7A50T, in terms of logic cells on the 3CG board.
Processor memory is comprised of 32KB L1 caches, both instruction and data. It has 1MB of a unified L2 cache, which is shared between the processors, and dual-core or quad-core will share that memory. Additionally, there’s a 32-bit interface to the 2GB of LPDDR4 main memory.
Working with the Zinq UltraScale+, you will boot up the processor system first, then when you configure the programmable logic, that control will be done by the processing system.
- 32KB L1 Caches
- Fastest (specific to processor)
- 1MB Unified L2 Cache
- Faster & Shared Between Processors
- 2GB LPDDR4 Main Memory
- 32-bit Data Width
All the AcroPacks, including the Zynq UltraScale+, include a x1 Gen. 1 PCI Express link to the module over the front finger connector, which is 2.5GB per second. With the Zynq, the x1 link is to the PS-GTR. APZU MPSoCs include integrated blocks for PCIe that are compliant PCI Express Base Specification Revision 3.1. There are also two general-purpose DMA controllers on the Zynq UltraScale+.
- APZU Include PCIe
- x1 at Gen. 1 Rates
- Compliant PCIe Base Specification Revision 3.1
- 2 General-purpose DMA Controllers
APZU I/O Peripherals
As has been noted earlier, there is a secure digital interface, and this is the primary boot. It’s a 16GB micro SD. That is the primary boot and is included in the shipment of the product. This allows users to load PetaLinux and/or any other operating system that they may need.
In addition, there is a secondary boot option with a flash device, which is much smaller. So, users can do development using a micro SD flash card and then once the code is optimized, they can boot from the Quad Flash device.
Acromag uses I2C (“I squared C”), we communicate with a 2K EEPROM for the Ethernet Mac ID and for the power chip. That monitors voltages and temperatures on the board as well as on the chip, making sure that things stay within specifications.
As can be seen to the right: a picture of the AcroPack Zynq UltraScale+, with the heat spreader included. Power dissipation with approximately 80% of the resources used will be less than 5 watts.
Size = 70mm x 30mm
Weight = 35.18 g (including heat spreader)
Click here to Download PDF: What is FPGA Zynq UltraScale+ with MPSoC?
APZU PCIe Carriers
Carriers for the AcroPack Zinq UltraScale+, as well as Acromag’s other AcroPacks, are PCI Express server slot-based. At this time, there are four Acromag carrier cards available:
The APCe7012 supports one AcroPack, and is a x1 Edge connector interface. In addition, it’s a small, half-height card that can host other AcroPack modules that use isolated DC-to-DC modules for power.
- Supports 1 AcroPack
- Supports Analog Isolated Modules
- Available in Half-height
- 68-pin 0.8mm Connector
Comparatively, the APCe7022 is a dual AcroPack carrier and is a x4 Edge connector interface. The APCe7022 can also host other AcroPack modules. In addition, all Acromag carriers have been developed to be able to host Mini PCI Express cards.
- Supports 2 AcroPacks
- Two 68-pin 0.8mm Connectors
- PCIe x4 Edge Connector
APCe7040 & APCe7043
Acromag has two quad carrier boards for PCI Express servers: a full-length carrier, the APCe7040, as well as a 3/4-length carrier, the APCe7043. The APCe is the full-length version of the quad, as can be seen in the photo on the right. These can host analog isolated modules, in addition to up to four AcroPacks or combination of AcroPacks and Mini PCI Express cards.
To summarize, both versions:
- Support 4 AcroPacks
- Support Analog Isolated Modules
- 68-pin 0.8mm Connector
- PCIe x4 Edge Connector
More AcroPack Carriers for APZU:
XMC AcroPack Carrier
In addition, Acromag offers two 6U VPX carriers. The VPX4520 has an expansion plane interface, while the VPX4521 has a data plane interface to the backplane. Each of these supports up to four AcroPack modules and one XMC card that can be either a Vita 42 or Vita 61 configuration. Each of these supports up to four AcroPack modules and one XMC card that can be either a VITA 42 or VITA 61 configuration. They are available in either front I/O air-cooled or rear I/O conduction-cooled versions.
ACEX4041 Carrier & ARCX1100
The ACEX4041 carrier hosts four AcroPack modules as well as an M.2 storage and requires a Type 10 Com Express processor. We then took this carrier, and introduced the ARCX1100, which packages the ACEX-4041 in an IP65 chassis and has a removable 2.5 inch solid state drive.
ACPS3310/20 Compact PCIe Serial
AcroPacks also support Compact PCI Express serial. There are two versions, both of which host two AcroPack modules and support isolated analog I/O: the ACPS3310 supports front I/O, while the ACPS3320 supports rear I/O.
Engineering Design Kit, Software Drivers & Development Tools
Engineering Design Kit
At first purchase, the Engineering Design Kit (EDK), APZU-EDK, that Acromag offers is a must-buy. It provides example code of intellectual property blocks, as well as the RAM, system monitors, and AXI interfaces to the digital I/O. It’s “known good code,” that users can import into their Vitis™ development environment, knowing that this code has been debugged, and thus, works. The EDK is a starting point for users to add to their application, then start making modifications. Accordingly, this is a one-time purchase.
- APSW-API-LNX: Support for Linux; free website download (see the software tab on the link)
- APSW-API-WIN: Support for Windows/DLL drivers
- APSW-API-VXW: Support for VxWorks 7.0
I/O Breakout Panel
The 5028-626 I/O breakout panel is also recommended, it has a 68-pin, male-to-male cable that’s one foot long and one side of it plugs into the carrier front panel. The other side plugs into the breakout panel, thus bringing an Ethernet port, UART to USB port, digital I/O at the jumper blocks and power and reset buttons out to the field.
Vivado® 2020.1 Design Suite – Vitis
Vitis is a unified software platform that sits on top of Vivado and allows you to do your development on a variety of different Xilinx platforms, including the Systems on a Chip (SoCs) as well as the Versal ACAPs. The Vitis software provides compilers, analyzers, and debuggers so users can design, develop software, and develop code.
Correspondingly, PetaLinux is an embedded Linux systems development kit that targets Xilinx SoCs designs. It includes U-Boot, Linux Kernel, and Device Tree, as well as Root Filesystem components.
Learn more: How to Use Vivado for FPGA Modifications
Typical applications for the AcroPack Zinq UltraScale+ include:
Hardware in the Loop
Firstly, hardware in the loop used for simulation is a key application for these modules.
With the processing, memory, and algorithms available, users can go from one type of format to another with their protocol converters.
Video Capture & Recording
Interfaces such as camera link, USB, and Ethernet make the APZU very capable for video capture and recording.
Video Packet Interrogation
The APZU is very beneficial for applications such as facial recognition or license plate numbers, etc.
The ability to simulate not only a missile, but other types of weapons, makes these modules ideal.
Sensor Data Acquisition
The APZU can take a variety of different sensor data acquisition, then process them, transmit them along, etc.
Learn more: What are FPGAs and Their Applications?
FPGA Product Lines Supported
Without a doubt, Acromag is very strongly partnered with Xilinx. We currently support the Virtex-4, the Virtex-5, Spartan-6, Kintex-7, and the Artix-7 (in both an XMC form factor and in an AcroPack form factor). Furthermore, with the development of the new Zynq UltraScale+, we’ll be supporting the APZU-30x family. Coming soon, we will have an XMC Zynq UltraScale+ offering.
Watch the Webcast: FPGA Zynq UltraScale+ MPSoC Introduction
For more information about FPGAs, Zynq UltraScale+, or any Acromag product, click the link below and our sales team will be happy to answer your questions!