The AcPC8625A is a nonintelligent slave board that interfaces four IP modules to the CompactPCI (cPCI) bus.
All 200 I/O points are brought out the rear J4 and J5 connectors. This convenience eliminates messy cables from hanging out the front of the cage. In addition to a more efficient cage wiring design, it is also much easier to insert and replace boards. And with Acromag’s 80mm transition module (TRANS-C200), all 200 I/O points are easily ported out the back of the cage.
Performance Specifications
General
Acromag’s carrier boards provide full data access to the IP module’s I/O, ID, interrupt spaces, and memory. With full access to the programmable registers, you can easily configure and control the operation of the IP modules from the CompactPCI bus. Up to two interrupt requests are supported for each IP module. All board interrupts are mapped to PCI bus INTA# signal. Individual passive filters on each IP power supply line provide optimum filtering and noise isolation between the IP modules and the carrier board. IP Compliance (ANSI/VITA 4): Meets IP specs per ANSI/VITA 4-1995 (8MHz and 32MHz) and IP I/O mapping to PICMG 2.4 R1.0. Electrical/mechanical interface: Supports single or double size IP modules. 32-bit IP modules are not supported. IP Module I/O space, ID space, INT space, and MEM space supported. Interrupts: Supports two interrupt requests per IP module and interrupt acknowledge cycles via access to IP INT space.CompactPCI bus Compliance
Meets PCI spec. V2.1 and PICMG 2.0, R2.1. Data transfer bus: Slave with 32-bit, 16-bit, and 8-bit data transfer operation 32-bit read/write accesses are implemented as two 16-bit transfers to the IPs. Interrupts: CompactPCI bus INTA# interrupt signal. Up to two requests sourced from each IP mapped to INTA#. Interrupt vectors come from IP modules via access to IP module INT space. Plug-and-Play: The system maps the base address into the PCI bus 32-bit memory space.Power Requirements
Power 3.3V (±5%): 300mA maximum. 5V (±5%): 30mA maximum. ±12V (±5%): 0mA (not used). Plus IP module load. MTBF: Contact factoryEnvironmental
Operating temperature: -25 to 85°C (AcPC8625) or -40 to 85°C (AcPC8625E models). Storage temperature: -25 to 85°C (AcPC8625) or -40 to 85°C (AcPC8625E models). Relative humidity: 5 to 95% non-condensing. The AcPC8625A is a drop in replacement for the AcPC8625, please see known difference statement below. Known difference between the AcPC8625 and the AcPC8625A statement.Showing 1–16 of 33 results
-
AcPC8625A: Nonintelligent 6U cPCI IP Carrier
- Four IP module slots
- Rear access I/O
- Plug-and-play carrier configuration and interrupt support
$900 – $1,020Select options -
AcPC8630A: Nonintelligent 3U cPCI IP Carrier, Front I/O
- Two IP module slots
- Front access I/O
- Plug-and-play carrier configuration and interrupt support
$780 – $900Select options -
AcPC8635A: Nonintelligent 3U cPCI IP Carrier, Rear I/O
- Two IP module slots
- Rear access I/O
- Plug-and-play carrier configuration and interrupt support
$780 – $900Select options -
APC8621A: Non-intelligent PCI Bus Carrier, Half-Length
- Nonintelligent PCI bus carrier
- Holds three IP modules
$720Select options -
APCe8650: Non-intelligent PCI Express Bus Carrier
- Non-intelligent PCIe bus carrier
- Holds four IP modules
$900 – $1,050Select options -
IP-EP-EDK: Engineering Design Kit
- CD containing
- schematics
- parts list
- part location drawing
- example VHDL source
- other utility files.
- One kit required
$320Select options - CD containing
-
IP-EP200: Cyclone II FPGA with Digital I/O (JTAG-configured)
- Up to 48 TTL or 24 differential RS485
- Altera Cyclone II EP2C20 FPGA programmable via JTAG port or via the IP bus directly
$1,300 – $1,430Select options -
IP220A: Analog Output Industry Pack Module, 12-bit D/A
- 8 or 16 voltage output channels
- Independent D/A converter on each channel
- 11µS settling time
- ±10V output range
$865 – $1,395Select options