• 8 Analog DC Voltage Outputs ±10V (calibrated), ±5V (sub-range)
• 4 Discrete Voltage I/O Channels 0-32V DC
• 12 to 32V DC Power (2.8W)
• Modbus TCP/IP, Ethernet/IP, Profinet
• i2o® peer-to-peer available for Modbus TCP/IP only

The XT1540 interfaces analog output and discrete I/O signals between measurement and control devices over Ethernet. Discrete I/O are individually configurable for input or high-side switched output operation.

• Configuration Software
• USB-to-RS232 Adapter
• RS232-to-RS485 Adapter
• Interface Cable

 

• 10/100Mbps
• 15 to 36V DC power supply required
• Five shielded RJ-45 sockets, 8-pin, 10Base-T / 100Base-TX

Acromag’s five-port Ethernet switch is specially designed for use in industrial applications. Rugged construction and a variety of security features ensure reliable operation under demanding conditions.

• Active-Low Inputs, Sinking Outputs (Low-Side Switching)
• 12 input and/or 12 output channels
• 0 to 35V DC I/O range
• 10 to 36V DC, 24V AC power
• Modbus-RTU high-speed RS-485

These modules provide twelve discrete input and/or output channels. Isolation separates the I/O, power, and network circuits. Network communication adheres to the industry-standard RS-485 Modbus-RTU protocol.    

• Active-High Inputs, Sourcing Outputs (High-Side Switching)
• 12 input and/or 12 output channels
• 0 to 35V DC I/O range
• 10 to 36V DC, 24V AC power
• Modbus-RTU high-speed RS-485

These modules provide twelve discrete input and/or output channels. Isolation separates the I/O, power, and network circuits. Network communication adheres to the industry-standard RS-485 Modbus RTU protocol.

• 4 input channels
• 0 to 20mA DC (0 to 20A AC with AC sensor) or ±10V DC input range
• 4 alarm channels, open drain MOSFETS (1A DC loads, 0 to 35V DC)
• 10 to 36V DC, 24V AC power
• Modbus RTU high-speed RS-485

This signal conditioner is a four-channel analog input module with four discrete outputs. It provides isolation between input, output, power, and network circuits.

• 4 analog output channels
• 0 to 20mA or 0 to 10V DC output range
• 4 discrete output channels, open drain MOSFETS (1A DC loads, 0 to 35V DC)
• 10 to 36V DC, 24V AC power
• Modbus RTU high-speed RS-485

These modules drive four analog output channels and also feature four discrete outputs for on/off control. Isolation separates the output, power, and network circuits. Network communication adheres to the industry-standard RS-485 Modbus RTU protocol.

• 4 input channels, thermocouple (types J, K, T, R, S, E, B, N) or millivolt (±100mV DC) input
• 4 alarm channels, open drain MOSFETS (1A DC loads, 0 to 35V DC)
• 10 to 36V DC, 24V AC power
• Modbus-RTU high-speed RS-485

This signal conditioner is a four-channel analog input module with four discrete outputs. It filters and linearizes thermocouple inputs while providing isolation between input, output, power, and network circuits. Cold junction compensation and upscale/downscale sensor break detection are standard.  

• 2 or 4 input channels, RTD (100 ohm Pt, 120 ohm Ni, 10 ohm Cu) or resistance (0 to 500 ohms) input
• Solid-state relays discrete output, Form A, SPST-NO
• 10 to 36V DC, 24V AC power
• Modbus-RTU high-speed RS-485

This signal conditioner is a dual or quad-channel analog input module with one discrete/relay output per input channel and a Modbus interface. It filters and linearizes RTD or resistance inputs while providing isolation between input, output, power, and network circuits.

• 2 input channels, 0 to 50KHz in 3 selectable ranges: Amplitudes up to 140V AC peak, Amplitudes up to 200V peak, Pulse counter range of 0 to 65535
• Solid-state discrete output relays (1A DC loads), 0 to 48V DC
• 10 to 36V DC, 24V AC power
• Modbus-RTU high-speed RS-485

This signal conditioner is a two-channel analog input module with discrete outputs and Modbus communication. It conditions periodic or pulse waveform inputs and provides solid-state relays for limit alarms or ON/OFF control.

• 4 analog inputs
• 2 analog output
• 6 discrete I/O channels
• Ethernet/IP, Modbus TCP/IP
• i2o peer-to-peer available for Modbus TCP/IP only

These modules provide an isolated Ethernet network interface for analog and discrete I/O signals. Multi-range analog inputs and outputs support a wide variety of industrial devices. High-resolution, low noise, A/D and D/A converters deliver high accuracy and reliability.

• 16-chanel single-ended voltage input
• DB25 port for 8B modules
• Modbus TCP/IP communication

These modules interface high-level analog input signals to an Ethernet control network. A high-performance design ensures reliable measurements and dependable operation.  

• 6-channel differential analog current or voltage input
• Ethernet/IP, Modbus TCP/IP
• i2o peer-to-peer available for Modbus TCP/IP only

These modules provide an isolated Ethernet network interface for six analog input channels. Differential inputs eliminate ground loops and thus the need for isolators in many applications. Multi-range inputs accept signals from a variety of sensors and devices. High-resolution, low noise, A/D converters deliver high accuracy and reliability.

• DC Current or DC Voltage Signals
• 6 input channels, 0 to 20mA in 3 selectable ranges (0 to 20 amps AC with optinal AC sensor) or ±78mV to ±10V DC with eight range options
• 12 to 36V DC power
• Profibus-DP, RS-485 network up to 12Mbaud

These modules provide an isolated Profibus-DP network interface for six analog input channels. Differential inputs eliminate ground loops and thus the need for isolators in any applications.

• 12-channel single-ended analog current or voltage input
• Ethernet/IP or Modbus TCP/IP communication

These modules provide an isolated Ethernet network interface for twelve analog input channels. Compact design saves space and lowers system costs. Multi-range inputs accept signals from a variety of sensors and devices. High-resolution, low noise, A/D converters deliver high accuracy and reliability.