• 0-11mA, 0-20mA, 4-20mA, ±20mA, or 0-20 amps AC Input
• 8 analog differential current input channels
• 12 to 32V DC Power (2.8W)
• Modbus TCP/IP, Ethernet/IP, Profinet
• i2o® peer-to-peer available for Modbus TCP/IP only

The XT1210 offers an isolated Ethernet network interface for up to eight differential current input channels. Isolated differential inputs deliver better measurements, superior noise rejection, and eliminate the need for current loop isolators.

• ±5V, ±10V, 0-5V, 0-10V Input
• 8 analog differential voltage input channels
• 12 to 32V DC Power (2.8W)
• Modbus TCP/IP, Ethernet/IP, Profinet
• i2o® peer-to-peer available for Modbus TCP/IP only

The XT1220 offers an isolated Ethernet network interface for up to eight differential voltage input channels.

• 0-11mA, 0-20mA, 4-20mA, ±20mA, or 0-20 amps AC Input
• 16 analog single-ended current input channels
• 12 to 32V DC Power (2.8W)
• Modbus TCP/IP, Ethernet/IP, Profinet
• i2o® peer-to-peer available for Modbus TCP/IP only

The XT1230 offers an isolated Ethernet network interface for up to to sixteen single-ended current input channels.

• Input: ±5V, ±10V, 0-5V, 0-10V
• 16 analog single-ended voltage input channels
• 12 to 32V DC Power (2.8W)
• Modbus TCP/IP, Ethernet/IP, Profinet
• i2o® peer-to-peer available for Modbus TCP/IP only

The XT1240 offers an isolated Ethernet network interface for up to to sixteen single-ended voltage input channels.

• 4 Analog DC Current Outputs
• 4 Discrete Voltage I/O Channels
• 12 to 32V DC Power (2.8W)
• Modbus TCP/IP, Ethernet/IP, Profinet
• i2o® peer-to-peer available for Modbus TCP/IP only

The XT1530 interfaces analog output and discrete I/O signals between measurement and control devices over Ethernet. Discrete I/O are individually configurable for input or high-side switched output operation.

• 8 Analog DC Voltage Outputs ±10V (calibrated), ±5V (sub-range)
• 4 Discrete Voltage I/O Channels 0-32V DC
• 12 to 32V DC Power (2.8W)
• Modbus TCP/IP, Ethernet/IP, Profinet
• i2o® peer-to-peer available for Modbus TCP/IP only

The XT1540 interfaces analog output and discrete I/O signals between measurement and control devices over Ethernet. Discrete I/O are individually configurable for input or high-side switched output operation.

• Configuration Software
• USB-to-RS232 Adapter
• RS232-to-RS485 Adapter
• Interface Cable

 

• Active-Low Inputs, Sinking Outputs (Low-Side Switching)
• 12 input and/or 12 output channels
• 0 to 35V DC I/O range
• 10 to 36V DC, 24V AC power
• Modbus-RTU high-speed RS-485

These modules provide twelve discrete input and/or output channels. Isolation separates the I/O, power, and network circuits. Network communication adheres to the industry-standard RS-485 Modbus-RTU protocol.    

• Active-High Inputs, Sourcing Outputs (High-Side Switching)
• 12 input and/or 12 output channels
• 0 to 35V DC I/O range
• 10 to 36V DC, 24V AC power
• Modbus-RTU high-speed RS-485

These modules provide twelve discrete input and/or output channels. Isolation separates the I/O, power, and network circuits. Network communication adheres to the industry-standard RS-485 Modbus RTU protocol.  

• 4 input channels
• 0 to 20mA DC (0 to 20A AC with AC sensor) or ±10V DC input range
• 4 alarm channels, open drain MOSFETS (1A DC loads, 0 to 35V DC)
• 10 to 36V DC, 24V AC power
• Modbus RTU high-speed RS-485

This signal conditioner is a four-channel analog input module with four discrete outputs. It provides isolation between input, output, power, and network circuits.      

• 4 analog output channels
• 0 to 20mA or 0 to 10V DC output range
• 4 discrete output channels, open drain MOSFETS (1A DC loads, 0 to 35V DC)
• 10 to 36V DC, 24V AC power
• Modbus RTU high-speed RS-485

These modules drive four analog output channels and also feature four discrete outputs for on/off control. Isolation separates the output, power, and network circuits. Network communication adheres to the industry-standard RS-485 Modbus RTU protocol.          

• 4 input channels, thermocouple (types J, K, T, R, S, E, B, N) or millivolt (±100mV DC) input
• 4 alarm channels, open drain MOSFETS (1A DC loads, 0 to 35V DC)
• 10 to 36V DC, 24V AC power
• Modbus-RTU high-speed RS-485

This signal conditioner is a four-channel analog input module with four discrete outputs. It filters and linearizes thermocouple inputs while providing isolation between input, output, power, and network circuits. Cold junction compensation and upscale/downscale sensor break detection are standard.    

• 2 or 4 input channels, RTD (100 ohm Pt, 120 ohm Ni, 10 ohm Cu) or resistance (0 to 500 ohms) input
• Solid-state relays discrete output, Form A, SPST-NO
• 10 to 36V DC, 24V AC power
• Modbus-RTU high-speed RS-485

This signal conditioner is a dual or quad-channel analog input module with one discrete/relay output per input channel and a Modbus interface. It filters and linearizes RTD or resistance inputs while providing isolation between input, output, power, and network circuits.      

• 2 input channels, 0 to 50KHz in 3 selectable ranges: Amplitudes up to 140V AC peak, Amplitudes up to 200V peak, Pulse counter range of 0 to 65535
• Solid-state discrete output relays (1A DC loads), 0 to 48V DC
• 10 to 36V DC, 24V AC power
• Modbus-RTU high-speed RS-485

This signal conditioner is a two-channel analog input module with discrete outputs and Modbus communication. It conditions periodic or pulse waveform inputs and provides solid-state relays for limit alarms or ON/OFF control.