New Optocoupler and Interposing Relay Modules

New 6-Channel Optocoupler and Interposing Relay Modules Monitor/Control High-Voltage Field Devices

Acromag releases relay interface modules to monitor or control high-energy actuators (on/off, high/low, open/close) using remote I/O, PLCs, or other distributed control systems with DC logic signaling.

New BusWorks XT Optocoupler and Interposing Relay ModulesAcromag’s new BusWorks® XT Series multi-channel optocoupler and interposing relay modules connect discrete field devices to measurement & control system I/O modules. The XTA-120V-6 optocoupler modules have six individually isolated 120V AC/DC digital (discrete) inputs to sense on/off levels and provide 5-32V DC logic outputs to a fieldbus input module or a controller. The XTA-MRNO-6 interposing relay module receives 4-32V DC logic-level signals from an output module or controller to switch six mechanical relay outputs. These two high-voltage relay interface modules offer a high-density, cost-effective solution to safely monitor or control inductive and other high-power loads (motors, valves, solenoids, etc.) with control system input/output modules that only support low- level DC signals. Pricing starts at $150 for the mechanical relay output module and $180 for the optocoupler input module.

“These multi-channel discrete contact sensor and relay output modules offer a safe, isolated interface between high-energy field devices and sensitive control system I/O modules,” explained Don Lupo, sales and marketing director of Acromag’s process products group. “By adding optocouplers and relays, you can use PLC, DCS, or remote I/O modules with 5-24V logic circuits to operate 120V AC/DC contactors.”

The XTA-120V-6 six-channel optocoupler is intended for use with control system digital input modules to monitor contact closures or mains power supply on/off voltage levels. Each channel senses the presence or absence of high-level voltage to determine the status of proximity switches, limit switches, toggle switches, push buttons, contacts, and other devices. Opto-isolators control a mosfet switch for a TTL-level output to safely interface the status of the monitored device.

The XTA-MRNO-6 six-channel mechanical relay is used with digital output modules to drive high energy loads. This unit serves as an interim digital interface to switch high voltage devices at high currents based on digital DC logic inputs. Each output has normally open Form A mechanical relay contacts (SPST-NO). LEDs on each channel indicate the output state for convenient troubleshooting.

Both modules can drive audible or visual alarms. Common uses involve operation of stack lights, bells, whistles, lights, and horns. While the XTA-MRNO-6 is intended for switching AC/DC inductive loads at high currents, the XTA-120V-6 is designed to drive low-current devices such as solid-state relays, LEDs, relay coils, solenoids, and incandescent lamps.

An innovative housing design is only 22.5mm wide and features removable front-facing terminal blocks for easier wiring. All units run off a 12- 32V DC power source at the terminals or through an integrated power connector bussed along the DIN rail that can provide primary or redundant power. Fail-safe operation is supported. Suitable for use in harsh environments, modules operate from -40 to 85°C with 1500V AC isolation and surge/transient protection. They can also withstand 25g shock and 4g vibration. CE and UL/cUL Class 1 Division 2 Zone 2 hazardous location approvals are pending.

Acromag has designed and manufactured measurement and control products for more than 55 years. With a headquarters near Detroit, Michigan and a global network of sales representatives and distributors, Acromag products are sold worldwide. They offer a complete line of industrial I/O products including process instruments, signal conditioning equipment, data acquisition boards, distributed I/O modules, and network communication devices. Industries served include manufacturing, water services, power generation, mining, defense, and transportation.

For more information about Acromag products, call the Inside Sales Department at (248) 295-0880 or Marketing Communications at (248) 295-0865. Send faxes to (248) 624-9234. You can also visit us online at www.acromag.com, e-mail sales@acromag.com, or write Acromag at P.O. Box 437, Wixom, MI 48393-7037 USA.

Contacts: Sales - Inside Sales Department (e-mail: sales @ acromag.com)
Editorial: Robert Greenfield, Mktg. Comm. Mgr. (rgreenfield @ acromag.com)

All trademarks are the property of their respective owners.